Re: [hylafax-users] Err No carrier detected.

["Roper, Brent" <Brent.Roper@xxxxxxxxxxxx>]

I forgot to add that the HylaFax version is 4.1.7

Also I add the modem config file below

 

I am open to any suggestions.

 

# Configuration for using the Class 1 command interface with

# a USR Courier or Sportster modem and XON/XOFF flow control.

#

#

CountryCode:            1

AreaCode:         713

FAXNumber:        +1 713 xxx-xxxx

LongDistancePrefix:     1    

InternationalPrefix:    11   

DialStringRules:  etc/dialrules    

ServerTracing:          1

SessionTracing:         0xffffffff

RecvFileMode:           644

LogFileMode:            644

DeviceMode:       666

RingsBeforeAnswer:      2    

SpeakerVolume:          off

GettyArgs:        -h %l dx_%s

LocalIdentifier:  APS-Houston-Pharmacy   

TagLineFont:            etc/lutRS18.pcf

TagLineFormat:          From %%l|%c|Page %%P of %%T        

MaxRecvPages:           25         

#                      

#                      

# Modem-related stuff: should reflect modem command interface                      

# and hardware connection/cabling (e.g. flow control).                       

#                      

ModemType:        Class1            # use class 1 interface

ModemRate:        19200       # rate for DCE-DTE communication

ModemFlowControl: xonxoff           # software flow control

#                      

ModemSetupDTRCmd: ATS13=1&D2  # setup so DTR drop resets modem         

ModemSetupDCDCmd: AT&C1       # setup so DCD reflects carrier (or not) 

ModemNoFlowCmd:         AT&H0&I0&R1 # setup modem for no flow control  

ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control        

ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control        

ModemResultCodesCmd:    ATQ0X4            # enable result codes  

#                      

ModemMfrQueryCmd: !USR             

ModemModelQueryCmd:     ATI3             

ModemRevQueryCmd: ATI7        # XXX returns a multi-line result  

#                      

# When AT+FCLASS=1 is issued the modem automatically switches                      

# to software flow control; these parameters let the fax software                  

# reset flow control as needed after entering Class 1.                       

#                      

Class1NFLOCmd:          AT&H0&I0&R1 # setup modem for no flow control  

Class1HFLOCmd:          AT&H1&I0&R2 # setup modem for hardware flow control  

Class1SFLOCmd:                      # modem does this automatically

#                      

"# This should resolve ""DIS/DTC received 3 times"" errors:"                       

#                      

Class1ResponseWaitCmd:  AT+FRS=1    # wait after sending TCF for response    

#                

# The remainder of this configuration is included so that the                

"# modem ""idles"" in Class 0 while not sending or receiving facsimile."                 

#                

ModemSetupAACmd:  AT+FCLASS=0 # leave modem idling in class 0    

ModemAnswerCmd:         AT+FCLASS=1A      # answer in Class 1

#                

# Disables the reporting of bad frames by the modem.  This             

# overcomes a firmware problem in the x2 and V90 Sportsters.                 

# It is not necessary for the Courier modem.               

#                

"Class2NRCmd:    AT+FNR=1,1,1,0"               

#                

#Caller Id Support                 

#                

ModemResetCmds:         AT#CID=1

CIDName:                “NAME =”

CIDNumber:              “NMBR =”

 

Thanks

---

From: hylafax-users-bounce@xxxxxxxxxxx [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Roper, Brent
Sent: Friday, July 16, 2004 2:05 PM
To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users]

 

All,

 

This is a box running SuSE 9.0 with 6 USR 56k fax/modems on it.  I have written a script so that each time a fax is received it pipes faxcover into sendfax to send a 1 page fax back to the original sender to confirm the receipt of the fax.  On this particular box the only port that can send out a fax is ttyS0 all the rest get No carrier detected.  I have tried with the @ and without neither work.  Here is an excerpt from the log file.

 

"Jul 16 08:22:19.58: [30109]: --> return result ""15129281825"""

Jul 16 08:22:19.58: [30109]: <-- [12:AT+FCLASS=1\r]

Jul 16 08:22:19.82: [30109]: --> [2:OK]

"Jul 16 08:22:19.82: [30109]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled"

Jul 16 08:22:19.92: [30109]: DIAL 15129281825

Jul 16 08:22:19.92: [30109]: <-- [16:ATDT15129281825\r]

Jul 16 08:23:17.84: [30109]: --> [10:NO CARRIER]

Jul 16 08:23:17.84: [30109]: SEND FAILED: JOB 60 DEST 5129281825 ERR No carrier detected

 

Thanks in advance for any help.

 

Brent