[hylafax-users] fsc error sending to remote panasonic

[Borut Kurnik <borut@xxxxxxxxxx>]

Hi!

I have problem sending to remote Panasonic fax device.
I can only send one page, then this happens.

Hylafax 4.1.8
RedHat 9
Modem is 3com U.S. Robotics Faxserver

<fax>/etc/config ->
----------------------------8<-------------------------------
LogFacility:     daemon
CountryCode:          386
AreaCode:          01
LongDistancePrefix:    00
InternationalPrefix:       00
DialStringRules:     etc/dialrules
ServerTracing:       0x097FF
SessionTracing:      0x097FF
PageChop:            none
RingsBeforeAnswer:   1
ModemClass:          "any: modem[01]"
----------------------------8<-------------------------------

<fax>/etc/config.ttyS0 ->
----------------------------8<-------------------------------
CountryCode:		386
AreaCode:		01
FAXNumber:		4790060
LongDistancePrefix:	00
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		0x097FF
SessionTracing:		0x097FF
RecvFileMode:		0644
LogFileMode:		0644
DeviceMode:		0644
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l %s"
# LocalIdentifier:	""
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%s|%c|Page %%p of %%t"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).

# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and RTS/CTS flow control. 
#
# CONFIG:CLASS1:1444:.*:RTSCTS: Manufacturer=USRobotics
Model=Courier/Sportster
# CONFIG:CLASS1:1445:.*:RTSCTS: Manufacturer=USRobotics
Model=Courier/Sportster
# CONFIG:CLASS1:2886:.*:RTSCTS: Manufacturer=USRobotics
Model=Courier/Sportster
# CONFIG:CLASS1:3366:.*:RTSCTS: Manufacturer=USRobotics Model=Courier
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use class 1 interface
ModemRate:		 19200		# max rate for DCE-DTE communication
ModemFlowControl:	rtscts		# hardware flow control
#
ModemSetupDTRCmd:	ATS13=1&D2	# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
ModemNoFlowCmd:		AT&H0&I0&R1	# setup modem for no flow control
ModemHardFlowCmd:	AT&H1&I0&R2	# setup modem for hardware flow control
ModemSoftFlowCmd:	AT&H2&I2&R1	# setup modem for software flow control
ModemResultCodesCmd:	ATQ0X4		# enable result codes
#
ModemMfrQueryCmd:	!USR
ModemModelQueryCmd:	ATI3
ModemRevQueryCmd:	ATI7		# XXX, returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:		AT&H0&I0&R1	# setup modem for no flow control
Class1HFLOCmd:		AT&H1&I0&R2	# setup modem for hardware flow control
Class1SFLOCmd:		""		# modem does this automatically
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:	AT+FCLASS=0&H1&I0&R2	# leave modem in class 0
ModemAnswerCmd:		AT+FCLASS=1&H1&I0&R2A	# force RTS/CTS after change
#
Class2NRCmd: AT+FNR=1,1,1,0 #setup status reporting command 
#
ModemDialCmd:      ATX3DT%s
PageChop:          none 
RingsBeforeAnswer: 1
----------------------------8<-------------------------------


And the log:

   ---- Transcript of session follows ----

Jul 13 14:11:41.27: [14344]: SESSION BEGIN 000000140 070954205740
Jul 13 14:11:41.27: [14344]: HylaFAX (tm) Version 4.1.8
Jul 13 14:11:41.27: [14344]: SEND FAX: JOB 100 DEST 00070954205740
COMMID 000000140 DEVICE '/dev/modem0'
Jul 13 14:11:41.27: [14344]: MODEM set DTR OFF
Jul 13 14:11:41.27: [14344]: DELAY 75 ms
Jul 13 14:11:41.34: [14344]: MODEM set DTR ON
Jul 13 14:11:41.34: [14344]: DELAY 2600 ms
Jul 13 14:11:48.02: [14344]: MODEM set baud rate: 19200 baud, input flow
RTS/CTS, output flow RTS/CTS
Jul 13 14:11:48.02: [14344]: DELAY 10 ms
Jul 13 14:11:48.03: [14344]: MODEM flush i/o
Jul 13 14:11:48.03: [14344]: <-- [4:ATZ\r]
Jul 13 14:11:48.17: [14344]: --> [2:OK]
Jul 13 14:11:48.17: [14344]: DELAY 3000 ms
Jul 13 14:11:51.17: [14344]: <-- [5:ATE0\r]
Jul 13 14:11:51.31: [14344]: --> [4:ATE0]
Jul 13 14:11:51.31: [14344]: --> [2:OK]
Jul 13 14:11:51.31: [14344]: <-- [5:ATV1\r]
Jul 13 14:11:51.45: [14344]: --> [2:OK]
Jul 13 14:11:51.45: [14344]: <-- [7:ATQ0X4\r]
Jul 13 14:11:51.59: [14344]: --> [2:OK]
Jul 13 14:11:51.59: [14344]: <-- [7:ATS0=0\r]
Jul 13 14:11:51.73: [14344]: --> [2:OK]
Jul 13 14:11:51.73: [14344]: <-- [7:ATS8=2\r]
Jul 13 14:11:51.87: [14344]: --> [2:OK]
Jul 13 14:11:51.87: [14344]: <-- [8:ATS7=60\r]
Jul 13 14:11:52.01: [14344]: --> [2:OK]
Jul 13 14:11:52.01: [14344]: <-- [12:AT&H1&I0&R2\r]
Jul 13 14:11:52.17: [14344]: --> [2:OK]
Jul 13 14:11:52.17: [14344]: <-- [11:ATS13=1&D2\r]
Jul 13 14:11:52.31: [14344]: --> [2:OK]
Jul 13 14:11:52.31: [14344]: <-- [6:AT&C1\r]
Jul 13 14:11:52.45: [14344]: --> [2:OK]
Jul 13 14:11:52.45: [14344]: <-- [12:AT+FCLASS=1\r]
Jul 13 14:11:52.59: [14344]: --> [2:OK]
Jul 13 14:11:52.59: [14344]: <-- [12:AT&H1&I0&R2\r]
Jul 13 14:11:52.73: [14344]: --> [2:OK]
Jul 13 14:11:52.73: [14344]: <-- [21:AT+FCLASS=0&H1&I0&R2\r]
Jul 13 14:11:52.88: [14344]: --> [2:OK]
Jul 13 14:11:52.88: [14344]: <-- [5:ATM0\r]
Jul 13 14:11:53.02: [14344]: --> [2:OK]
Jul 13 14:11:53.02: [14344]: STATE CHANGE: RUNNING -> SENDING
Jul 13 14:11:53.02: [14344]: MODEM input buffering enabled
Jul 13 14:11:53.02: [14344]: <-- [12:AT+FCLASS=1\r]
Jul 13 14:11:53.26: [14344]: --> [2:OK]
Jul 13 14:11:53.26: [14344]: <-- [12:AT&H1&I0&R2\r]
Jul 13 14:11:53.50: [14344]: --> [2:OK]
Jul 13 14:11:53.51: [14344]: DIAL 00070954205740
Jul 13 14:11:53.51: [14344]: <-- [21:ATX3DT00070954205740\r]
Jul 13 14:12:23.61: [14344]: --> [7:CONNECT]
Jul 13 14:12:23.61: [14344]: MODEM input buffering disabled
Jul 13 14:12:25.33: [14344]: --> HDLC<45:FF C0 04 00 00 9E 00 00 00 41
F0 90 48 00 08 A0 40 A9 13 11 01 01 80 80 92 40 92 B2 0A 04 D2 32 92 B2
82 2A 04 B2 F2 CA C2 F2 C0 1F 98>
Jul 13 14:12:25.33: [14344]: --> [2:OK]
Jul 13 14:12:25.33: [14344]: REMOTE NSF "00 00 79 00 00 00 82 0F 09 12
00 10 05 02 95 C8 88 80 80 01 01 49 02 49 4D 50 20 4B 4C 49 4D 41 54 20
4D 4F 53 43 4F 03 F8"
Jul 13 14:12:25.33: [14344]: NSF remote fax equipment: Panasonic 
Jul 13 14:12:25.33: [14344]: NSF remote station ID: "IMP KLIMAT MOSCO"
Jul 13 14:12:25.33: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:12:25.35: [14344]: --> [7:CONNECT]
Jul 13 14:12:26.03: [14344]: --> HDLC<25:FF C0 02 0C 2C EC AC 0C 4C 2C
04 04 04 04 04 04 04 04 04 04 04 04 04 D0 89>
Jul 13 14:12:26.03: [14344]: --> [2:OK]
Jul 13 14:12:26.03: [14344]: REMOTE CSI "4205740"
Jul 13 14:12:26.03: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:12:26.05: [14344]: --> [7:CONNECT]
Jul 13 14:12:26.38: [14344]: --> HDLC<11:FF C8 01 00 72 1D 01 01 88 A9
FC>
Jul 13 14:12:26.38: [14344]: --> [5:ERROR]
Jul 13 14:12:26.38: [14344]: MODEM Command error
Jul 13 14:12:26.38: [14344]: FCS error
Jul 13 14:12:26.38: [14344]: DELAY 200 ms
Jul 13 14:12:26.58: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:12:26.60: [14344]: --> [7:CONNECT]
Jul 13 14:12:26.60: [14344]: --> [2:10 03]
Jul 13 14:12:26.60: [14344]: --> [5:ERROR]
Jul 13 14:12:26.60: [14344]: MODEM Command error
Jul 13 14:12:26.60: [14344]: FCS error
Jul 13 14:12:26.60: [14344]: DELAY 200 ms
Jul 13 14:12:26.80: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:12:26.82: [14344]: --> [7:CONNECT]
Jul 13 14:12:26.83: [14344]: --> [16:03 00 6C 56 00 A0 6C 56 00 A0 6C 56
00 A0 6C 56]
Jul 13 14:12:26.83: [14344]: --> [5:ERROR]
Jul 13 14:12:26.83: [14344]: MODEM Command error
Jul 13 14:12:26.83: [14344]: FCS error
Jul 13 14:12:26.83: [14344]: DELAY 200 ms
Jul 13 14:12:27.03: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:12:34.03: [14344]: --> [0:]
Jul 13 14:12:34.03: [14344]: MODEM <Empty line>
Jul 13 14:12:34.03: [14344]: MODEM TIMEOUT: waiting for v.21 carrier
Jul 13 14:12:34.04: [14344]: --> [2:OK]
Jul 13 14:12:34.04: [14344]: DELAY 200 ms
Jul 13 14:12:34.24: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:12:36.31: [14344]: --> [7:CONNECT]
Jul 13 14:12:38.14: [14344]: --> HDLC<45:FF C0 04 00 00 9E 00 00 00 41
F0 90 48 00 08 A0 40 A9 13 11 01 01 80 80 92 40 92 B2 0A 04 D2 32 92 B2
82 2A 04 B2 F2 CA C2 F2 C0 1F 98>
Jul 13 14:12:38.14: [14344]: --> [2:OK]
Jul 13 14:12:38.14: [14344]: REMOTE NSF "00 00 79 00 00 00 82 0F 09 12
00 10 05 02 95 C8 88 80 80 01 01 49 02 49 4D 50 20 4B 4C 49 4D 41 54 20
4D 4F 53 43 4F 03 F8"
Jul 13 14:12:38.14: [14344]: NSF remote fax equipment: Panasonic 
Jul 13 14:12:38.14: [14344]: NSF remote station ID: "IMP KLIMAT MOSCO"
Jul 13 14:12:38.14: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:12:38.16: [14344]: --> [7:CONNECT]
Jul 13 14:12:38.84: [14344]: --> HDLC<25:FF C0 02 0C 2C EC AC 0C 4C 2C
04 04 04 04 04 04 04 04 04 04 04 04 04 D0 89>
Jul 13 14:12:38.84: [14344]: --> [2:OK]
Jul 13 14:12:38.84: [14344]: REMOTE CSI "4205740"
Jul 13 14:12:38.84: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:12:38.86: [14344]: --> [7:CONNECT]
Jul 13 14:12:39.18: [14344]: --> HDLC<11:FF C8 01 00 72 1D 01 01 88 A9
FF>
Jul 13 14:12:39.18: [14344]: --> [2:OK]
Jul 13 14:12:39.18: [14344]: REMOTE best rate 9600 bit/s
Jul 13 14:12:39.18: [14344]: REMOTE max page width 1728 pixels in 215 mm
Jul 13 14:12:39.18: [14344]: REMOTE max unlimited page length
Jul 13 14:12:39.18: [14344]: REMOTE best vres 7.7 line/mm
Jul 13 14:12:39.18: [14344]: REMOTE best format 1-D MR
Jul 13 14:12:39.18: [14344]: REMOTE best 20 ms, 10 ms/scanline
Jul 13 14:12:39.18: [14344]: USE 9600 bit/s
Jul 13 14:12:39.18: [14344]: USE 20 ms, 10 ms/scanline
Jul 13 14:12:39.18: [14344]: SEND file "docq/doc113.ps;00"
Jul 13 14:12:39.19: [14344]: USE page width 1728 pixels in 215 mm
Jul 13 14:12:39.19: [14344]: USE unlimited page length
Jul 13 14:12:39.19: [14344]: USE 3.85 line/mm
Jul 13 14:12:39.19: [14344]: USE 1-D MR
Jul 13 14:12:39.19: [14344]: SEND training at v.29 9600 bit/s
Jul 13 14:12:39.19: [14344]: <-- [9:AT+FTH=3\r]
Jul 13 14:12:39.38: [14344]: --> [7:CONNECT]
Jul 13 14:12:39.38: [14344]: <-- HDLC<23:FF C0 C2 4C CC 4C AC 0C 0C CC
8C 0C 6C 1C CC D4 04 04 04 04 04 04 04>
Jul 13 14:12:39.41: [14344]: --> [7:CONNECT]
Jul 13 14:12:39.41: [14344]: <-- HDLC<6:FF C8 C1 00 60 10>
Jul 13 14:12:41.35: [14344]: --> [2:OK]
Jul 13 14:12:41.35: [14344]: <-- [9:AT+FTS=7\r]
Jul 13 14:12:41.44: [14344]: --> [2:OK]
Jul 13 14:12:41.44: [14344]: <-- [10:AT+FTM=96\r]
Jul 13 14:12:41.76: [14344]: --> [7:CONNECT]
Jul 13 14:12:43.29: [14344]: --> [2:OK]
Jul 13 14:12:43.29: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:12:44.31: [14344]: --> [7:CONNECT]
Jul 13 14:12:45.22: [14344]: --> HDLC<5:FF C8 22 67 DD>
Jul 13 14:12:45.22: [14344]: --> [2:OK]
Jul 13 14:12:45.22: [14344]: SEND training at v.29 7200 bit/s
Jul 13 14:12:45.22: [14344]: <-- [9:AT+FTH=3\r]
Jul 13 14:12:45.42: [14344]: --> [7:CONNECT]
Jul 13 14:12:45.42: [14344]: <-- HDLC<23:FF C0 C2 4C CC 4C AC 0C 0C CC
8C 0C 6C 1C CC D4 04 04 04 04 04 04 04>
Jul 13 14:12:45.45: [14344]: --> [7:CONNECT]
Jul 13 14:12:45.45: [14344]: <-- HDLC<6:FF C8 C1 00 70 10>
Jul 13 14:12:47.39: [14344]: --> [2:OK]
Jul 13 14:12:47.39: [14344]: <-- [9:AT+FTS=7\r]
Jul 13 14:12:47.48: [14344]: --> [2:OK]
Jul 13 14:12:47.48: [14344]: <-- [10:AT+FTM=72\r]
Jul 13 14:12:47.80: [14344]: --> [7:CONNECT]
Jul 13 14:12:49.34: [14344]: --> [2:OK]
Jul 13 14:12:49.34: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:12:50.26: [14344]: --> [7:CONNECT]
Jul 13 14:12:51.26: [14344]: --> HDLC<5:FF C8 22 67 DD>
Jul 13 14:12:51.26: [14344]: --> [2:OK]
Jul 13 14:12:51.26: [14344]: SEND training at v.27ter 4800 bit/s
Jul 13 14:12:51.26: [14344]: <-- [9:AT+FTH=3\r]
Jul 13 14:12:51.46: [14344]: --> [7:CONNECT]
Jul 13 14:12:51.46: [14344]: <-- HDLC<23:FF C0 C2 4C CC 4C AC 0C 0C CC
8C 0C 6C 1C CC D4 04 04 04 04 04 04 04>
Jul 13 14:12:51.49: [14344]: --> [7:CONNECT]
Jul 13 14:12:51.49: [14344]: <-- HDLC<6:FF C8 C1 00 50 10>
Jul 13 14:12:53.43: [14344]: --> [2:OK]
Jul 13 14:12:53.43: [14344]: <-- [9:AT+FTS=7\r]
Jul 13 14:12:53.52: [14344]: --> [2:OK]
Jul 13 14:12:53.52: [14344]: <-- [10:AT+FTM=48\r]
Jul 13 14:12:54.54: [14344]: --> [7:CONNECT]
Jul 13 14:12:56.08: [14344]: --> [2:OK]
Jul 13 14:12:56.08: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:12:56.66: [14344]: --> [7:CONNECT]
Jul 13 14:12:57.72: [14344]: --> HDLC<5:FF C8 21 57 BE>
Jul 13 14:12:57.72: [14344]: --> [2:OK]
Jul 13 14:12:57.72: [14344]: TRAINING succeeded
Jul 13 14:12:57.72: [14344]: DELAY 75 ms
Jul 13 14:12:57.79: [14344]: <-- [10:AT+FTM=48\r]
Jul 13 14:12:58.84: [14344]: --> [7:CONNECT]
Jul 13 14:12:58.84: [14344]: SEND begin page
Jul 13 14:13:11.39: [14344]: SENT 13750 bytes of data
Jul 13 14:13:13.59: [14344]: SENT 624 bytes of data
Jul 13 14:13:13.59: [14344]: SEND 1D RTC
Jul 13 14:13:13.59: [14344]: SEND end page
Jul 13 14:13:22.89: [14344]: --> [2:OK]
Jul 13 14:13:22.89: [14344]: <-- [9:AT+FTS=9\r]
Jul 13 14:13:23.00: [14344]: --> [2:OK]
Jul 13 14:13:23.00: [14344]: SEND send EOP (no more pages or documents)
Jul 13 14:13:23.00: [14344]: <-- [9:AT+FTH=3\r]
Jul 13 14:13:23.16: [14344]: --> [7:CONNECT]
Jul 13 14:13:23.16: [14344]: <-- HDLC<3:FF C8 F4>
Jul 13 14:13:24.33: [14344]: --> [2:OK]
Jul 13 14:13:24.33: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:13:24.46: [14344]: --> [7:CONNECT]
Jul 13 14:13:24.46: [14344]: --> [2:10 03]
Jul 13 14:13:24.46: [14344]: --> [5:ERROR]
Jul 13 14:13:24.46: [14344]: MODEM Command error
Jul 13 14:13:24.46: [14344]: FCS error
Jul 13 14:13:24.46: [14344]: SEND send EOP (no more pages or documents)
Jul 13 14:13:24.46: [14344]: <-- [9:AT+FTH=3\r]
Jul 13 14:13:24.66: [14344]: --> [7:CONNECT]
Jul 13 14:13:24.66: [14344]: <-- HDLC<3:FF C8 F4>
Jul 13 14:13:25.83: [14344]: --> [2:OK]
Jul 13 14:13:25.83: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:13:26.26: [14344]: --> [10:NO CARRIER]
Jul 13 14:13:26.26: [14344]: MODEM No carrier
Jul 13 14:13:26.26: [14344]: SEND send EOP (no more pages or documents)
Jul 13 14:13:26.26: [14344]: <-- [9:AT+FTH=3\r]
Jul 13 14:13:26.46: [14344]: --> [7:CONNECT]
Jul 13 14:13:26.46: [14344]: <-- HDLC<3:FF C8 F4>
Jul 13 14:13:27.63: [14344]: --> [2:OK]
Jul 13 14:13:27.63: [14344]: <-- [9:AT+FRH=3\r]
Jul 13 14:13:27.76: [14344]: --> [7:CONNECT]
Jul 13 14:13:27.76: [14344]: --> [2:10 03]
Jul 13 14:13:27.76: [14344]: --> [5:ERROR]
Jul 13 14:13:27.76: [14344]: MODEM Command error
Jul 13 14:13:27.76: [14344]: FCS error
Jul 13 14:13:27.76: [14344]: No response to MPS or EOP repeated 3 tries
Jul 13 14:13:27.76: [14344]: <-- [9:AT+FTH=3\r]
Jul 13 14:13:27.96: [14344]: --> [7:CONNECT]
Jul 13 14:13:27.96: [14344]: <-- HDLC<3:FF C8 DF>
Jul 13 14:13:29.13: [14344]: --> [2:OK]
Jul 13 14:13:29.13: [14344]: MODEM input buffering enabled
Jul 13 14:13:29.13: [14344]: SEND FAILED: JOB 100 DEST 00070954205740
ERR No response to MPS or EOP repeated 3 tries; too many attempts to
send
Jul 13 14:13:29.13: [14344]: <-- [5:ATH0\r]
Jul 13 14:13:29.37: [14344]: --> [2:OK]
Jul 13 14:13:29.37: [14344]: MODEM set DTR OFF
Jul 13 14:13:29.37: [14344]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
Jul 13 14:13:29.37: [14344]: SESSION END

    ---- Unsent job status ----

   Destination: 00070954205740
         JobID: 100
       GroupID: 100
        Sender: Samo Hrvatin
      Mailaddr: samo.hrvatin@xxxxxxxxxxxxx
        CommID: 000000140
Submitted From: 10.0.254.199
    Page Width: 194 (mm)
   Page Length: 281 (mm)
    Resolution: 98 (lpi)
        Status: No response to MPS or EOP repeated 3 tries; too many
attempts to send
       Dialogs: 1 (exchanges with remote device)
         Dials: 0 (consecutive failed calls to destination)
         Calls: 1 (total phone calls placed)
         Pages: 0 (pages transmitted)
      TotPages: 1 (total pages to transmit)
      Attempts: 1 (attempts to send current page)
        Dirnum: 0 (directory of next page to send)

    ---- Documents submitted for transmission ----

The following documents were submitted for transmission and are
available on the server for reuse until they are automatically
purged when this job is removed.  Documents may also be manually
removed using the faxrm command; consult faxrm(1) for information.

Filename                 Size Type
docq/doc113.ps          22652 PostScript

Thanks,

Borut

-- 
Borut Kurnik <borut@xxxxxxxxxx>


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*