[hylafax-users] Problem with fax-receiving

[Orbán Attila <attila@xxxxxxxxxx>]

Hi,

i've a Hylafax server with gentoo linux OS and Zyxel OMNI 56k external
modem,
almost everything is OK, but sometimes this is the log:
(if somebody is sending a fax with an "older" - i don't know what type of -
fax machine)

Jul 02 05:55:06.40: [ 2091]: SESSION BEGIN 00000118 ###########
Jul 02 05:55:06.40: [ 2091]: HylaFAX (tm) Version 4.1.8
Jul 02 05:55:06.40: [ 2091]: <-- [4:ATA\r]
Jul 02 05:55:16.08: [ 2091]: --> [4:+FCO]
Jul 02 05:55:16.08: [ 2091]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Jul 02 05:55:16.08: [ 2091]: RECV FAX: begin
Jul 02 05:55:16.32: [ 2091]: --> [27:+FTI:"Fax                 "]
Jul 02 05:55:16.32: [ 2091]: REMOTE TSI "Fax"
Jul 02 05:55:16.32: [ 2091]: --> [20:+FCS:1,5,0,0,1,0,0,0]
Jul 02 05:55:16.32: [ 2091]: REMOTE wants 14400 bit/s
Jul 02 05:55:16.32: [ 2091]: REMOTE wants page width 1728 pixels in 215 mm
Jul 02 05:55:16.32: [ 2091]: REMOTE wants A4 page length (297 mm)
Jul 02 05:55:16.32: [ 2091]: REMOTE wants 7.7 line/mm
Jul 02 05:55:16.32: [ 2091]: REMOTE wants 2-D MR
Jul 02 05:55:16.32: [ 2091]: --> [2:OK]
Jul 02 05:55:16.32: [ 2091]: <-- [7:AT+FDR\r]
Jul 02 05:55:21.33: [ 2091]: --> [20:+FCS:1,5,0,0,1,0,0,0]
Jul 02 05:55:21.33: [ 2091]: REMOTE wants 14400 bit/s
Jul 02 05:55:21.33: [ 2091]: REMOTE wants page width 1728 pixels in 215 mm
Jul 02 05:55:21.33: [ 2091]: REMOTE wants A4 page length (297 mm)
Jul 02 05:55:21.33: [ 2091]: REMOTE wants 7.7 line/mm
Jul 02 05:55:21.33: [ 2091]: REMOTE wants 2-D MR
Jul 02 05:55:21.33: [ 2091]: --> [7:CONNECT]
Jul 02 05:55:21.33: [ 2091]: RECV: begin page
Jul 02 05:55:21.33: [ 2091]: RECV: send trigger 022
Jul 02 05:55:21.33: [ 2091]: <-- data [1]
Jul 02 05:55:39.56: [ 2091]: RECV: 32719 bytes of data, 849 total lines
Jul 02 05:55:57.70: [ 2091]: RECV: 32767 bytes of data, 2092 total lines
Jul 02 05:55:59.47: [ 2091]: RECV: 3023 bytes of data, 2399 total lines
(no more lines in the log, and hylafax is running with this job)

it seems the server is running, but it isn't any communication between
remote fax and my modem. If i call my fax-server number, the line is
engaged or it has an error, i think the modem's holding the line.

I tried to restart hylafax (/etc/init.d/hylafax restart or stop/start),
but nothing... the server was "receiving" fax...

I tried to reset the modem, but the 'faxstat' said,
that it's receiving the fax, but the phone line isn't engaged.

If I restarted Gentoo, the server closed the log file:

Jul 02 07:24:17.83: [ 2091]: CLOSE /dev/ttyS0
(at 07:24!!! Last log message was at 05:55!!!)

After restart, the hylafax is working well again. But the fax's lost.
It isn't a "big" problem. My big problem is: I don't receive/send another
fax, while the modem is holding the line... :(

What's the problem?

Attila

My Hylafax version: 4.1.8-r3

My modemconfig:

CountryCode:            **
AreaCode:               *
FAXNumber:              ************
LongDistancePrefix:     06
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0666
LogFileMode:            0644
DeviceMode:             0666
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "NothingSetup"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25

ModemType:              Class2.0        # use this to supply a hint
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0
Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D (direct)
Class2CQCmd:            ""              # commands to enable copy quality
proc.
Class2AbortCmd:         AT+FKS          # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality
capabilities
Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities
Class2TBCCmd:           AT+FPP=0        # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter
Class2BUGCmd:           AT+FBU=1        # enable HDLC frame tracing
Class2LIDCmd:           AT+FLI          # set local identifier command
Class2DCCCmd:           AT+FCC          # set modem capabilities command
Class2DISCmd:           AT+FIS          # set session parameters command
Class2DDISCmd:          ""              # disable pre-dial DIS command hack
Class2CIGCmd:           AT+FPI          # set polling identifier command
Class2NRCmd:            AT+FNR=1,1,1,1  # setup status reporting command
Class2PIECmd:           AT+FIE=0        # disable interrupt-enable command
Class2PTSCmd:           AT+FPS          # set post-page status command
Class2PTSQueryCmd:      AT+FPS?         # set post-page status query command
Class2SPLCmd:           AT+FSP          # set polling indicator command
Class2NFLOCmd:          AT+FLO=0        # set no flow control command
Class2SFLOCmd:          AT+FLO=1        # set software flow control command
Class2HFLOCmd:          AT+FLO=2        # set hardware flow control command






____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*