[hylafax-users] Problems with PPS and sending with Rocket

[Pedro Rocadas <procadas@xxxxxxxxx>]

Hi guys. After a fresh instalation here is some
problems that I'm getting into.
Red Hat 9.0 hylafax 4.2.0beta1 for RH8. I have some
considerations here: noisy lines (PBX), modem firmare,
bad port?

I was forced to put off-line the port of the
Rocketport(ISA) card that I was using for outbound
jobs. I tried sending fax to a Ricoh 1700 and a
Toshiba and the results are pretty the same, but the
ugglyest was to the Ricoh

Log:

Jun 17 10:40:23.71: [ 8261]: SESSION BEGIN 000000150
XXXXXXXXXXXX
Jun 17 10:40:23.71: [ 8261]: HylaFAX (tm) Version
4.2.0beta1
Jun 17 10:40:23.71: [ 8261]: SEND FAX: JOB 50 DEST
225512794 COMMID 000000150 DEVICE '/dev/ttyR0'
Jun 17 10:40:23.71: [ 8261]: <-- [12:AT+FCLASS=1\r]
Jun 17 10:40:23.82: [ 8261]: --> [2:OK]
Jun 17 10:40:23.83: [ 8261]: DIAL 0,XXXXXXXXX
Jun 17 10:40:23.83: [ 8261]: <--
[16:ATDT0,XXXXXXXXX\r]
Jun 17 10:40:42.31: [ 8261]: --> [7:CONNECT]
Jun 17 10:40:43.45: [ 8261]: --> [2:OK]
Jun 17 10:40:43.45: [ 8261]: REMOTE NSF "00 00 25 00
00 00 12 10 4D 02 00 50 00 2A B8 2C"
Jun 17 10:40:43.45: [ 8261]: NSF remote fax equipment:
Ricoh
Jun 17 10:40:43.45: [ 8261]: <-- [9:AT+FRH=3\r]
Jun 17 10:40:43.47: [ 8261]: --> [7:CONNECT]
Jun 17 10:40:43.80: [ 8261]: --> [2:OK]
Jun 17 10:40:43.80: [ 8261]: REMOTE NSF "00 00 25 01
4E 50 42"
Jun 17 10:40:43.80: [ 8261]: NSF remote fax equipment:
Ricoh
Jun 17 10:40:43.80: [ 8261]: <-- [9:AT+FRH=3\r]
Jun 17 10:40:43.82: [ 8261]: --> [7:CONNECT]
Jun 17 10:40:44.12: [ 8261]: --> [2:OK]
Jun 17 10:40:44.12: [ 8261]: HDLC frame with bad
control field 0x1
Jun 17 10:40:44.12: [ 8261]: DELAY 200 ms
Jun 17 10:40:44.32: [ 8261]: <-- [9:AT+FRH=3\r]
Jun 17 10:40:51.32: [ 8261]: --> [0:]
Jun 17 10:40:51.32: [ 8261]: MODEM <Empty line>
Jun 17 10:40:51.32: [ 8261]: <-- data [1]
Jun 17 10:40:51.52: [ 8261]: MODEM <Timeout>
Jun 17 10:40:51.52: [ 8261]: DELAY 200 ms
Jun 17 10:40:51.72: [ 8261]: <-- [9:AT+FRH=3\r]
Jun 17 10:40:58.72: [ 8261]: --> [0:]
Jun 17 10:40:58.72: [ 8261]: MODEM <Empty line>
Jun 17 10:40:58.72: [ 8261]: <-- data [1]
Jun 17 10:40:58.92: [ 8261]: MODEM <Timeout>
Jun 17 10:40:58.92: [ 8261]: DELAY 200 ms
Jun 17 10:40:59.12: [ 8261]: <-- [9:AT+FRH=3\r]
Jun 17 10:41:06.12: [ 8261]: --> [0:]
Jun 17 10:41:06.12: [ 8261]: MODEM <Empty line>
Jun 17 10:41:06.12: [ 8261]: <-- data [1]
Jun 17 10:41:06.32: [ 8261]: MODEM <Timeout>
Jun 17 10:41:06.32: [ 8261]: DELAY 200 ms
Jun 17 10:41:06.52: [ 8261]: <-- [9:AT+FRH=3\r]
Jun 17 10:41:13.52: [ 8261]: --> [0:]
Jun 17 10:41:13.52: [ 8261]: MODEM <Empty line>
Jun 17 10:41:13.52: [ 8261]: <-- data [1]
Jun 17 10:41:13.72: [ 8261]: MODEM <Timeout>
Jun 17 10:41:13.72: [ 8261]: DELAY 200 ms
Jun 17 10:41:13.92: [ 8261]: <-- [9:AT+FRH=3\r]
Jun 17 10:41:20.92: [ 8261]: --> [0:]
Jun 17 10:41:20.92: [ 8261]: MODEM <Empty line>
Jun 17 10:41:20.92: [ 8261]: <-- data [1]
Jun 17 10:41:21.12: [ 8261]: MODEM <Timeout>
Jun 17 10:41:21.12: [ 8261]: DELAY 200 ms
Jun 17 10:41:21.32: [ 8261]: <-- [9:AT+FRH=3\r]
Jun 17 10:41:28.32: [ 8261]: --> [0:]
Jun 17 10:41:28.32: [ 8261]: MODEM <Empty line>
Jun 17 10:41:28.32: [ 8261]: <-- data [1]
Jun 17 10:41:28.52: [ 8261]: MODEM <Timeout>
Jun 17 10:41:28.52: [ 8261]: DELAY 200 ms
Jun 17 10:41:28.72: [ 8261]: No answer (T.30 T1
timeout)
Jun 17 10:41:28.72: [ 8261]: SEND FAILED: JOB 50 DEST
XXXXXXXXX ERR No answer (T.30 T1 timeout)
Jun 17 10:41:28.72: [ 8261]: <-- [9:AT+FTH=3\r]
Jun 17 10:41:31.27: [ 8261]: --> [0:]
Jun 17 10:41:31.27: [ 8261]: <-- [5:ATH0\r]
Jun 17 10:41:36.27: [ 8261]: MODEM <Timeout>
Jun 17 10:42:06.30: [ 8261]: SESSION END 

The next log is from a Multitech modem and what is
strange is that I got a PPS error which, I guess,
shouldn't appears because ECM was used. 

Jun 17 11:08:44.60: [ 8838]: SESSION BEGIN 000000172
XXXXXXXXXXXX
Jun 17 11:08:44.60: [ 8838]: HylaFAX (tm) Version
4.2.0beta1
Jun 17 11:08:44.60: [ 8838]: SEND FAX: JOB 59 DEST
XXXXXXXXX COMMID 000000172 DEVICE '/dev/ttyS1'
Jun 17 11:08:44.60: [ 8838]: <-- [12:AT+FCLASS=1\r]
Jun 17 11:08:44.71: [ 8838]: --> [2:OK]
Jun 17 11:08:44.72: [ 8838]: DIAL 0,XXXXXXXXX
Jun 17 11:08:44.72: [ 8838]: <--
[16:ATDT0,XXXXXXXXX\r]
Jun 17 11:09:27.59: [ 8838]: --> [7:CONNECT]
Jun 17 11:09:28.68: [ 8838]: --> [2:OK]
Jun 17 11:09:28.68: [ 8838]: REMOTE NSF "AD 00 36 A0
00 00 00 00"
Jun 17 11:09:28.68: [ 8838]: NSF remote fax equipment:
HP
Jun 17 11:09:28.68: [ 8838]: <-- [9:AT+FRH=3\r]
Jun 17 11:09:28.70: [ 8838]: --> [7:CONNECT]
Jun 17 11:09:29.10: [ 8838]: --> [2:OK]
Jun 17 11:09:29.10: [ 8838]: REMOTE best rate 33600
bit/s
Jun 17 11:09:29.10: [ 8838]: REMOTE max A4 page width
(215 mm)
Jun 17 11:09:29.10: [ 8838]: REMOTE max unlimited page
length
Jun 17 11:09:29.10: [ 8838]: REMOTE best vres 7.7
line/mm
Jun 17 11:09:29.10: [ 8838]: REMOTE best format 2-D
MMR
Jun 17 11:09:29.10: [ 8838]: REMOTE supports T.30
Annex A, 256-byte ECM
Jun 17 11:09:29.10: [ 8838]: REMOTE best 0 ms/scanline
Jun 17 11:09:29.10: [ 8838]: USE 14400 bit/s
Jun 17 11:09:29.10: [ 8838]: USE error correction mode
Jun 17 11:09:29.10: [ 8838]: USE 0 ms/scanline
Jun 17 11:09:29.11: [ 8838]: SEND file
"docq/doc59.ps;01"
Jun 17 11:09:29.11: [ 8838]: USE A4 page width (215
mm)
Jun 17 11:09:29.11: [ 8838]: USE unlimited page length
Jun 17 11:09:29.11: [ 8838]: USE 7.7 line/mm
Jun 17 11:09:29.11: [ 8838]: USE 2-D MMR
Jun 17 11:09:29.11: [ 8838]: SEND training at v.17
14400 bit/s
Jun 17 11:09:29.11: [ 8838]: <-- [9:AT+FTH=3\r]
Jun 17 11:09:29.16: [ 8838]: --> [7:CONNECT]
Jun 17 11:09:29.16: [ 8838]: <-- data [23]
Jun 17 11:09:29.16: [ 8838]: <-- data [2]
Jun 17 11:09:30.94: [ 8838]: --> [7:CONNECT]
Jun 17 11:09:30.94: [ 8838]: <-- data [7]
Jun 17 11:09:30.94: [ 8838]: <-- data [2]
Jun 17 11:09:31.40: [ 8838]: --> [2:OK]
Jun 17 11:09:31.40: [ 8838]: <-- [9:AT+FTS=7\r]
Jun 17 11:09:31.49: [ 8838]: --> [2:OK]
Jun 17 11:09:31.49: [ 8838]: <-- [11:AT+FTM=145\r]
Jun 17 11:09:31.53: [ 8838]: --> [7:CONNECT]
Jun 17 11:09:31.53: [ 8838]: <-- data [1024]
Jun 17 11:09:31.53: [ 8838]: <-- data [1024]
Jun 17 11:09:31.53: [ 8838]: <-- data [652]
Jun 17 11:09:31.53: [ 8838]: <-- data [2]
Jun 17 11:09:34.64: [ 8838]: --> [2:OK]
Jun 17 11:09:34.64: [ 8838]: <-- [9:AT+FRH=3\r]
Jun 17 11:09:35.08: [ 8838]: --> [7:CONNECT]
Jun 17 11:09:36.05: [ 8838]: --> [2:OK]
Jun 17 11:09:36.05: [ 8838]: TRAINING succeeded
Jun 17 11:09:36.05: [ 8838]: SEND begin page
Jun 17 11:09:36.06: [ 8838]: Reading MH-compressed
image file
Jun 17 11:09:36.16: [ 8838]: SEND EOFB
Jun 17 11:09:36.16: [ 8838]: SEND send frame number 0
<sniped>
Jun 17 11:09:36.20: [ 8838]: DELAY 200 ms
Jun 17 11:09:36.39: [ 8838]: <-- [11:AT+FTM=146\r]
Jun 17 11:09:36.43: [ 8838]: --> [7:CONNECT]
Jun 17 11:09:36.43: [ 8838]: <-- data [1030]
Jun 17 11:09:36.43: [ 8838]: <-- data [1029]
Jun 17 11:09:36.43: [ 8838]: <-- data [1028]
Jun 17 11:09:36.43: [ 8838]: <-- data [1033]
Jun 17 11:09:38.43: [ 8838]: <-- data [1030]
Jun 17 11:09:38.43: [ 8838]: <-- data [1033]
Jun 17 11:09:38.43: [ 8838]: <-- data [1031]
Jun 17 11:09:38.43: [ 8838]: <-- data [1026]
Jun 17 11:09:40.43: [ 8838]: <-- data [1037]
Jun 17 11:09:40.43: [ 8838]: <-- data [1037]
Jun 17 11:09:40.43: [ 8838]: <-- data [1031]
Jun 17 11:09:40.43: [ 8838]: <-- data [1027]
Jun 17 11:09:42.39: [ 8838]: <-- data [1032]
Jun 17 11:09:42.39: [ 8838]: <-- data [1033]
Jun 17 11:09:42.39: [ 8838]: <-- data [1027]
Jun 17 11:09:44.39: [ 8838]: <-- data [1027]
Jun 17 11:09:44.39: [ 8838]: <-- data [1031]
Jun 17 11:09:44.39: [ 8838]: <-- data [1027]
Jun 17 11:09:44.39: [ 8838]: <-- data [1030]
Jun 17 11:09:46.26: [ 8838]: <-- data [1025]
Jun 17 11:09:46.26: [ 8838]: <-- data [1032]
Jun 17 11:09:46.26: [ 8838]: <-- data [1031]
Jun 17 11:09:48.26: [ 8838]: <-- data [1028]
Jun 17 11:09:48.26: [ 8838]: <-- data [1038]
Jun 17 11:09:48.26: [ 8838]: <-- data [1040]
Jun 17 11:09:48.26: [ 8838]: <-- data [1036]
Jun 17 11:09:50.33: [ 8838]: <-- data [1032]
Jun 17 11:09:50.33: [ 8838]: <-- data [1036]
Jun 17 11:09:50.33: [ 8838]: <-- data [1032]
Jun 17 11:09:52.33: [ 8838]: <-- data [1030]
Jun 17 11:09:52.33: [ 8838]: <-- data [1032]
Jun 17 11:09:52.33: [ 8838]: <-- data [493]
Jun 17 11:09:52.33: [ 8838]: <-- data [2]
Jun 17 11:09:54.70: [ 8838]: --> [2:OK]
Jun 17 11:09:54.70: [ 8838]: <-- [9:AT+FTS=9\r]
Jun 17 11:09:54.81: [ 8838]: --> [2:OK]
Jun 17 11:09:54.81: [ 8838]: <-- [9:AT+FTH=3\r]
Jun 17 11:09:54.86: [ 8838]: --> [7:CONNECT]
Jun 17 11:09:54.86: [ 8838]: <-- data [7]
Jun 17 11:09:54.86: [ 8838]: <-- data [2]
Jun 17 11:09:56.29: [ 8838]: --> [2:OK]
Jun 17 11:09:56.29: [ 8838]: SEND send PPS (partial
page signal)
Jun 17 11:09:56.29: [ 8838]: SEND send EOP (no more
pages or documents)
Jun 17 11:09:56.29: [ 8838]: <-- [9:AT+FRH=3\r]
Jun 17 11:09:59.39: [ 8838]: --> [0:]
Jun 17 11:09:59.39: [ 8838]: MODEM <Empty line>
Jun 17 11:09:59.39: [ 8838]: <-- data [1]
Jun 17 11:09:59.45: [ 8838]: --> [2:OK]
Jun 17 11:09:59.45: [ 8838]: <-- [9:AT+FTH=3\r]
Jun 17 11:09:59.50: [ 8838]: --> [7:CONNECT]
Jun 17 11:09:59.50: [ 8838]: <-- data [7]
Jun 17 11:09:59.50: [ 8838]: <-- data [2]
Jun 17 11:10:00.93: [ 8838]: --> [2:OK]
Jun 17 11:10:00.93: [ 8838]: SEND send PPS (partial
page signal)
Jun 17 11:10:00.93: [ 8838]: SEND send EOP (no more
pages or documents)
Jun 17 11:10:00.93: [ 8838]: <-- [9:AT+FRH=3\r]
Jun 17 11:10:04.03: [ 8838]: --> [0:]
Jun 17 11:10:04.03: [ 8838]: MODEM <Empty line>
Jun 17 11:10:04.03: [ 8838]: <-- data [1]
Jun 17 11:10:04.09: [ 8838]: --> [2:OK]
Jun 17 11:10:04.09: [ 8838]: <-- [9:AT+FTH=3\r]
Jun 17 11:10:04.14: [ 8838]: --> [7:CONNECT]
Jun 17 11:10:04.14: [ 8838]: <-- data [7]
Jun 17 11:10:04.14: [ 8838]: <-- data [2]
Jun 17 11:10:05.57: [ 8838]: --> [2:OK]
Jun 17 11:10:05.57: [ 8838]: SEND send PPS (partial
page signal)
Jun 17 11:10:05.57: [ 8838]: SEND send EOP (no more
pages or documents)
Jun 17 11:10:05.57: [ 8838]: <-- [9:AT+FRH=3\r]
Jun 17 11:10:08.67: [ 8838]: --> [0:]
Jun 17 11:10:08.67: [ 8838]: MODEM <Empty line>
Jun 17 11:10:08.67: [ 8838]: <-- data [1]
Jun 17 11:10:08.73: [ 8838]: --> [2:OK]
Jun 17 11:10:08.73: [ 8838]: No response to PPS
repeated 3 times.
Jun 17 11:10:08.73: [ 8838]: SEND end page
Jun 17 11:10:08.73: [ 8838]: <-- [9:AT+FTH=3\r]
Jun 17 11:10:08.78: [ 8838]: --> [7:CONNECT]
Jun 17 11:10:08.78: [ 8838]: <-- data [3]
Jun 17 11:10:08.78: [ 8838]: <-- data [2]
Jun 17 11:10:10.10: [ 8838]: --> [2:OK]
Jun 17 11:10:10.10: [ 8838]: SEND FAILED: JOB 59 DEST
XXXXXXXXX ERR No response to PPS repeated 3 ti
mes.; too many attempts to dial
Jun 17 11:10:10.10: [ 8838]: <-- [5:ATH0\r]
Jun 17 11:10:11.65: [ 8838]: --> [2:OK]
Jun 17 11:10:11.65: [ 8838]: SESSION END

Thanks for any help


		
__________________________________
Do you Yahoo!?
Yahoo! Mail is new and improved - Check it out!
http://promotions.yahoo.com/new_mail

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*