Re: [hylafax-users] No response to MPS repeated 3 times

[Matt Yeager <Matt@xxxxxxxxxxxxxxxxxx>]

Here is one example log. This is on one of the modems I have configured for
Fax Class 1.
I've removed the bulk of the pages sending, leaving the beginning and ending
pages.

Jun 08 10:55:10.22: [20442]: SESSION BEGIN 00011840 1877XXXXXXX
Jun 08 10:55:10.22: [20442]: HylaFAX (tm) Version 4.1.7
Jun 08 10:55:10.22: [20442]: SEND FAX: JOB 2615 DEST 1877XXXXXXX COMMID
00011840 DEVICE '/dev/ttyR5'
Jun 08 10:55:10.22: [20442]: DELAY 75 ms
Jun 08 10:55:10.30: [20442]: DELAY 2600 ms
Jun 08 10:55:13.91: [20442]: DELAY 10 ms
Jun 08 10:55:13.92: [20442]: <-- [4:ATZ\r]
Jun 08 10:55:13.96: [20442]: --> [2:OK]
Jun 08 10:55:13.96: [20442]: DELAY 3000 ms
Jun 08 10:55:16.96: [20442]: <-- [5:ATE0\r]
Jun 08 10:55:16.97: [20442]: --> [4:ATE0]
Jun 08 10:55:16.97: [20442]: --> [2:OK]
Jun 08 10:55:16.97: [20442]: <-- [5:ATV1\r]
Jun 08 10:55:16.98: [20442]: --> [2:OK]
Jun 08 10:55:16.98: [20442]: <-- [5:ATQ0\r]
Jun 08 10:55:16.99: [20442]: --> [2:OK]
Jun 08 10:55:16.99: [20442]: <-- [7:ATS0=0\r]
Jun 08 10:55:17.00: [20442]: --> [2:OK]
Jun 08 10:55:17.00: [20442]: <-- [7:ATS8=2\r]
Jun 08 10:55:17.01: [20442]: --> [2:OK]
Jun 08 10:55:17.01: [20442]: <-- [8:ATS7=60\r]
Jun 08 10:55:17.02: [20442]: --> [2:OK]
Jun 08 10:55:17.02: [20442]: <-- [6:AT&K3\r]
Jun 08 10:55:17.03: [20442]: --> [2:OK]
Jun 08 10:55:17.03: [20442]: <-- [6:AT&D2\r]
Jun 08 10:55:17.04: [20442]: --> [2:OK]
Jun 08 10:55:17.04: [20442]: <-- [6:AT&C1\r]
Jun 08 10:55:17.05: [20442]: --> [2:OK]
Jun 08 10:55:17.05: [20442]: <-- [12:AT+FCLASS=1\r]
Jun 08 10:55:17.06: [20442]: --> [2:OK]
Jun 08 10:55:17.06: [20442]: <-- [5:ATM0\r]
Jun 08 10:55:17.07: [20442]: --> [2:OK]
Jun 08 10:55:17.07: [20442]: <-- [12:AT+FCLASS=1\r]
Jun 08 10:55:17.19: [20442]: --> [2:OK]
Jun 08 10:55:17.19: [20442]: DIAL 1877XXXXXXX
Jun 08 10:55:17.19: [20442]: <-- [16:ATDT1877XXXXXXX\r]
Jun 08 10:55:28.78: [20442]: --> [7:CONNECT]
Jun 08 10:55:30.13: [20442]: --> [2:OK]
Jun 08 10:55:30.13: [20442]: REMOTE CSI ""
Jun 08 10:55:30.13: [20442]: <-- [9:AT+FRH=3\r]
Jun 08 10:55:30.15: [20442]: --> [7:CONNECT]
Jun 08 10:55:30.48: [20442]: --> [2:OK]
Jun 08 10:55:30.48: [20442]: REMOTE best rate 14400 bit/s
Jun 08 10:55:30.48: [20442]: REMOTE max page width 1728 pixels in 215 mm
Jun 08 10:55:30.48: [20442]: REMOTE max unlimited page length
Jun 08 10:55:30.48: [20442]: REMOTE best vres 7.7 line/mm
Jun 08 10:55:30.48: [20442]: REMOTE best format 2-D MMR
Jun 08 10:55:30.48: [20442]: REMOTE supports T.30 Annex A, ECM
Jun 08 10:55:30.48: [20442]: REMOTE best 0 ms/scanline
Jun 08 10:55:30.48: [20442]: USE 14400 bit/s
Jun 08 10:55:30.48: [20442]: USE 0 ms/scanline
Jun 08 10:55:30.48: [20442]: SEND file "docq/doc2618.ps;31"
Jun 08 10:55:30.48: [20442]: USE page width 1728 pixels in 215 mm
Jun 08 10:55:30.48: [20442]: USE unlimited page length
Jun 08 10:55:30.48: [20442]: USE 7.7 line/mm
Jun 08 10:55:30.48: [20442]: USE 1-D MR
Jun 08 10:55:30.48: [20442]: SEND training at v.17 14400 bit/s
Jun 08 10:55:30.48: [20442]: <-- [9:AT+FTH=3\r]
Jun 08 10:55:30.53: [20442]: --> [7:CONNECT]
Jun 08 10:55:30.53: [20442]: <-- data [23]
Jun 08 10:55:30.53: [20442]: <-- data [2]
Jun 08 10:55:32.32: [20442]: --> [7:CONNECT]
Jun 08 10:55:32.32: [20442]: <-- data [6]
Jun 08 10:55:32.32: [20442]: <-- data [2]
Jun 08 10:55:32.75: [20442]: --> [2:OK]
Jun 08 10:55:32.75: [20442]: <-- [9:AT+FTS=7\r]
Jun 08 10:55:32.84: [20442]: --> [2:OK]
Jun 08 10:55:32.84: [20442]: <-- [11:AT+FTM=145\r]
Jun 08 10:55:32.88: [20442]: --> [7:CONNECT]
Jun 08 10:55:32.88: [20442]: <-- data [1024]
Jun 08 10:55:32.88: [20442]: <-- data [1024]
Jun 08 10:55:32.88: [20442]: <-- data [652]
Jun 08 10:55:32.88: [20442]: <-- data [2]
Jun 08 10:55:35.99: [20442]: --> [2:OK]
Jun 08 10:55:35.99: [20442]: <-- [9:AT+FRH=3\r]
Jun 08 10:55:36.68: [20442]: --> [7:CONNECT]
Jun 08 10:55:37.63: [20442]: --> [2:OK]
Jun 08 10:55:37.63: [20442]: SEND training at v.17 12000 bit/s
Jun 08 10:55:37.63: [20442]: <-- [9:AT+FTH=3\r]
Jun 08 10:55:37.68: [20442]: --> [7:CONNECT]
Jun 08 10:55:37.68: [20442]: <-- data [23]
Jun 08 10:55:37.68: [20442]: <-- data [2]
Jun 08 10:55:39.47: [20442]: --> [7:CONNECT]
Jun 08 10:55:39.47: [20442]: <-- data [6]
Jun 08 10:55:39.47: [20442]: <-- data [2]
Jun 08 10:55:39.90: [20442]: --> [2:OK]
Jun 08 10:55:39.90: [20442]: <-- [9:AT+FTS=7\r]
Jun 08 10:55:39.99: [20442]: --> [2:OK]
Jun 08 10:55:39.99: [20442]: <-- [11:AT+FTM=121\r]
Jun 08 10:55:40.02: [20442]: --> [7:CONNECT]
Jun 08 10:55:40.02: [20442]: <-- data [1024]
Jun 08 10:55:40.02: [20442]: <-- data [1024]
Jun 08 10:55:40.02: [20442]: <-- data [202]
Jun 08 10:55:40.02: [20442]: <-- data [2]
Jun 08 10:55:43.13: [20442]: --> [2:OK]
Jun 08 10:55:43.13: [20442]: <-- [9:AT+FRH=3\r]
Jun 08 10:55:43.81: [20442]: --> [7:CONNECT]
Jun 08 10:55:44.79: [20442]: --> [2:OK]
Jun 08 10:55:44.79: [20442]: TRAINING succeeded
Jun 08 10:55:44.79: [20442]: DELAY 75 ms
Jun 08 10:55:44.87: [20442]: <-- [11:AT+FTM=122\r]
Jun 08 10:55:44.91: [20442]: --> [7:CONNECT]
Jun 08 10:55:44.91: [20442]: SEND begin page
Jun 08 10:55:44.91: [20442]: <-- data [1026]
...snip...
Jun 08 10:56:17.92: [20442]: <-- data [777]
Jun 08 10:56:17.92: [20442]: SENT 51976 bytes of data
Jun 08 10:56:17.92: [20442]: SEND 1D RTC
Jun 08 10:56:17.92: [20442]: <-- data [29]
Jun 08 10:56:17.92: [20442]: <-- data [2]
Jun 08 10:56:17.92: [20442]: SEND end page
Jun 08 10:56:19.93: [20442]: --> [2:OK]
Jun 08 10:56:19.93: [20442]: <-- [9:AT+FTS=7\r]
Jun 08 10:56:20.02: [20442]: --> [2:OK]
Jun 08 10:56:20.02: [20442]: SEND send MPS (more pages, same document)
Jun 08 10:56:20.02: [20442]: <-- [9:AT+FTH=3\r]
Jun 08 10:56:20.07: [20442]: --> [7:CONNECT]
Jun 08 10:56:20.07: [20442]: <-- data [3]
Jun 08 10:56:20.07: [20442]: <-- data [2]
Jun 08 10:56:21.38: [20442]: --> [2:OK]
Jun 08 10:56:21.38: [20442]: <-- [9:AT+FRH=3\r]
Jun 08 10:56:21.77: [20442]: --> [7:CONNECT]
Jun 08 10:56:22.71: [20442]: --> [2:OK]
Jun 08 10:56:22.71: [20442]: SEND recv MCF (message confirmation)
Jun 08 10:56:22.71: [20442]: SEND FAX (00011840): FROM XXXX@xxxxxxxxxxxx TO
1877XXXXXXX (page 1 of 27 sent in 0:52)
Jun 08 10:56:22.71: [20442]: USE page width 1728 pixels in 215 mm
Jun 08 10:56:22.71: [20442]: USE unlimited page length
Jun 08 10:56:22.71: [20442]: USE 7.7 line/mm
Jun 08 10:56:22.71: [20442]: USE 1-D MR
Jun 08 10:56:22.71: [20442]: DELAY 75 ms
Jun 08 10:56:22.79: [20442]: <-- [11:AT+FTM=122\r]
Jun 08 10:56:22.82: [20442]: --> [7:CONNECT]
Jun 08 10:56:22.82: [20442]: SEND begin page
Jun 08 10:56:22.82: [20442]: <-- data [1025]
...snip...
...snip...
Jun 08 11:13:37.24: [20442]: <-- data [1029]
Jun 08 11:13:37.24: [20442]: <-- data [1024]
Jun 08 11:13:39.78: [20442]: <-- data [517]
Jun 08 11:13:39.78: [20442]: SENT 62981 bytes of data
Jun 08 11:13:39.78: [20442]: SEND 1D RTC
Jun 08 11:13:39.78: [20442]: <-- data [29]
Jun 08 11:13:39.78: [20442]: <-- data [2]
Jun 08 11:13:39.78: [20442]: SEND end page
Jun 08 11:13:41.50: [20442]: --> [2:OK]
Jun 08 11:13:41.50: [20442]: <-- [9:AT+FTS=7\r]
Jun 08 11:13:41.59: [20442]: --> [2:OK]
Jun 08 11:13:41.59: [20442]: SEND send MPS (more pages, same document)
Jun 08 11:13:41.59: [20442]: <-- [9:AT+FTH=3\r]
Jun 08 11:13:41.64: [20442]: --> [7:CONNECT]
Jun 08 11:13:41.64: [20442]: <-- data [3]
Jun 08 11:13:41.64: [20442]: <-- data [2]
Jun 08 11:13:42.95: [20442]: --> [2:OK]
Jun 08 11:13:42.95: [20442]: <-- [9:AT+FRH=3\r]
Jun 08 11:13:43.37: [20442]: --> [7:CONNECT]
Jun 08 11:13:44.28: [20442]: --> [2:OK]
Jun 08 11:13:44.28: [20442]: SEND recv MCF (message confirmation)
Jun 08 11:13:44.28: [20442]: SEND FAX (00011840): FROM XXXX@xxxxxxxxxxxx TO
1877XXXXXXX (page 19 of 27 sent in 0:45)
Jun 08 11:13:44.28: [20442]: USE page width 1728 pixels in 215 mm
Jun 08 11:13:44.28: [20442]: USE unlimited page length
Jun 08 11:13:44.28: [20442]: USE 7.7 line/mm
Jun 08 11:13:44.28: [20442]: USE 1-D MR
Jun 08 11:13:44.28: [20442]: DELAY 75 ms
Jun 08 11:13:44.36: [20442]: <-- [11:AT+FTM=122\r]
Jun 08 11:13:44.39: [20442]: --> [7:CONNECT]
Jun 08 11:13:44.39: [20442]: SEND begin page
Jun 08 11:13:44.39: [20442]: <-- data [1026]
Jun 08 11:13:44.39: [20442]: <-- data [1024]
...snip...
Jun 08 11:14:22.49: [20442]: <-- data [1024]
Jun 08 11:14:25.03: [20442]: <-- data [1025]
Jun 08 11:14:25.03: [20442]: <-- data [1010]
Jun 08 11:14:25.03: [20442]: SENT 64497 bytes of data
Jun 08 11:14:25.03: [20442]: SEND 1D RTC
Jun 08 11:14:25.03: [20442]: <-- data [29]
Jun 08 11:14:25.03: [20442]: <-- data [2]
Jun 08 11:14:25.03: [20442]: SEND end page
Jun 08 11:14:27.78: [20442]: --> [2:OK]
Jun 08 11:14:27.78: [20442]: <-- [9:AT+FTS=7\r]
Jun 08 11:14:27.86: [20442]: --> [2:OK]
Jun 08 11:14:27.86: [20442]: SEND send MPS (more pages, same document)
Jun 08 11:14:27.86: [20442]: <-- [9:AT+FTH=3\r]
Jun 08 11:14:27.91: [20442]: --> [7:CONNECT]
Jun 08 11:14:27.91: [20442]: <-- data [3]
Jun 08 11:14:27.91: [20442]: <-- data [2]
Jun 08 11:14:29.22: [20442]: --> [2:OK]
Jun 08 11:14:29.22: [20442]: <-- [9:AT+FRH=3\r]
Jun 08 11:14:32.32: [20442]: --> [0:]
Jun 08 11:14:32.32: [20442]: MODEM <Empty line>
Jun 08 11:14:32.32: [20442]: <-- data [1]
Jun 08 11:14:32.38: [20442]: --> [2:OK]
Jun 08 11:14:32.38: [20442]: SEND send MPS (more pages, same document)
Jun 08 11:14:32.38: [20442]: <-- [9:AT+FTH=3\r]
Jun 08 11:14:32.43: [20442]: --> [7:CONNECT]
Jun 08 11:14:32.43: [20442]: <-- data [3]
Jun 08 11:14:32.43: [20442]: <-- data [2]
Jun 08 11:14:33.74: [20442]: --> [2:OK]
Jun 08 11:14:33.74: [20442]: <-- [9:AT+FRH=3\r]
Jun 08 11:14:36.84: [20442]: --> [0:]
Jun 08 11:14:36.84: [20442]: MODEM <Empty line>
Jun 08 11:14:36.84: [20442]: <-- data [1]
Jun 08 11:14:36.90: [20442]: --> [2:OK]
Jun 08 11:14:36.90: [20442]: SEND send MPS (more pages, same document)
Jun 08 11:14:36.90: [20442]: <-- [9:AT+FTH=3\r]
Jun 08 11:14:36.95: [20442]: --> [7:CONNECT]
Jun 08 11:14:36.95: [20442]: <-- data [3]
Jun 08 11:14:36.95: [20442]: <-- data [2]
Jun 08 11:14:38.26: [20442]: --> [2:OK]
Jun 08 11:14:38.26: [20442]: <-- [9:AT+FRH=3\r]
Jun 08 11:14:41.36: [20442]: --> [0:]
Jun 08 11:14:41.36: [20442]: MODEM <Empty line>
Jun 08 11:14:41.36: [20442]: <-- data [1]
Jun 08 11:14:41.42: [20442]: --> [2:OK]
Jun 08 11:14:41.42: [20442]: No response to MPS or EOP repeated 3 tries
Jun 08 11:14:41.42: [20442]: <-- [9:AT+FTH=3\r]
Jun 08 11:14:41.47: [20442]: --> [7:CONNECT]
Jun 08 11:14:41.47: [20442]: <-- data [3]
Jun 08 11:14:41.47: [20442]: <-- data [2]
Jun 08 11:14:42.78: [20442]: --> [2:OK]
Jun 08 11:14:42.78: [20442]: <-- [5:ATH0\r]
Jun 08 11:14:43.96: [20442]: --> [2:OK]
Jun 08 11:14:43.96: [20442]: SESSION END


Thanks for the help.

	-Matt Yeager






-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx]On Behalf Of Lee Howard
Sent: Tuesday, June 08, 2004 1:48 PM
To: Matt Yeager
Cc: 'hylafax-users@xxxxxxxxxxx'
Subject: Re: [hylafax-users] No response to MPS repeated 3 times


On 2004.06.08 10:50 Matt Yeager wrote:

> I can supply logs if that helps at all.

Class 1 logs would help us help you.  We can't help you, really, in 
Class 2 (you'd have to turn to Comtrol).

Lee.

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*