[hylafax-users] No answer (T.30 T1 timeout)

["Plus" <plus@xxxxxxxxxxxx>]

Hello all,

 

I have a computer with HylaFAX 4.1.3 on Red Hat Linux.

I can send fax, but sometime I can't receive fax and get the error "No answer (T.30 T1 timeout)" .

I don't find a solution. Can anybody help me?

I have attached my file config.ttyS0 and the error.

 

Regards,

Felix

 

-----

#
# Configuration for a Rockwell RC288DPi-based Class 1 modem.
#    Hayes Optima 28800         firmware rev ???
#    Microcom DeskPorte 28.8S   firmware rev V1.100K-V34_DS
#    PPI PM288FXMT              firmware rev 1.57
#
# Note that the modem does not lock the line rate for fax
# receive (at least not the PM288FXMT); but not sure whether
# current flow control settings are maintained or if it
# switches to XON/XOFF (testing host was too fast to see).
#
#

CountryCode:            0034
AreaCode:
FAXNumber:              968554355
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "Servidor de FAX"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "De %%m|%c|Pagina %%P de %%T"
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use this to supply a hint
ModemRate:              19200           # rate for DCE-DTE communication
ModemFlowControl:       rtscts          # default
#
ModemNoFlowCmd:         AT&K0           # setup no flow control
ModemHardFlowCmd:       AT&K3           # setup hardware flow control
ModemSoftFlowCmd:       AT&K4           # setup software flow control
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
#
ModemMfrQueryCmd:       !Rockwell
ModemModelQueryCmd:     !RC288DPi
ModemRevQueryCmd:       ATI3            # product information
#
ModemDialCmd:           ATDT%s          # T for tone dialing

 

-----

 

oct 29 14:24:43.02: [  853]: SESSION BEGIN 00001172 0034968174072
oct 29 14:24:43.02: [  853]: HylaFAX (tm) Version 4.1.3
oct 29 14:24:43.02: [  853]: <-- [4:ATA\r]
oct 29 14:24:49.41: [  853]: --> [7:CONNECT]
oct 29 14:24:49.41: [  853]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
oct 29 14:24:49.41: [  853]: RECV FAX: begin
oct 29 14:24:49.41: [  853]: <-- data [23]
oct 29 14:24:49.41: [  853]: <-- data [2]
oct 29 14:24:51.10: [  853]: --> [7:CONNECT]
oct 29 14:24:51.10: [  853]: <-- data [10]
oct 29 14:24:51.10: [  853]: <-- data [2]
oct 29 14:24:51.64: [  853]: --> [2:OK]
oct 29 14:24:51.64: [  853]: <-- [9:AT+FRH=3\r]
oct 29 14:24:54.74: [  853]: --> [0:]
oct 29 14:24:54.74: [  853]: MODEM <Empty line>
oct 29 14:24:54.74: [  853]: <-- data [1]
oct 29 14:24:54.80: [  853]: --> [2:OK]
oct 29 14:24:54.80: [  853]: DELAY 1500 ms
oct 29 14:24:56.30: [  853]: <-- [9:AT+FTH=3\r]
oct 29 14:24:56.37: [  853]: --> [7:CONNECT]
oct 29 14:24:56.37: [  853]: <-- data [23]
oct 29 14:24:56.37: [  853]: <-- data [2]
oct 29 14:24:58.15: [  853]: --> [7:CONNECT]
oct 29 14:24:58.15: [  853]: <-- data [10]
oct 29 14:24:58.15: [  853]: <-- data [2]
oct 29 14:24:58.69: [  853]: --> [2:OK]
oct 29 14:24:58.69: [  853]: <-- [9:AT+FRH=3\r]
oct 29 14:25:01.79: [  853]: --> [0:]
oct 29 14:25:01.79: [  853]: MODEM <Empty line>
oct 29 14:25:01.79: [  853]: <-- data [1]
oct 29 14:25:01.85: [  853]: --> [2:OK]
oct 29 14:25:01.85: [  853]: DELAY 1500 ms
oct 29 14:25:03.35: [  853]: <-- [9:AT+FTH=3\r]
oct 29 14:25:03.41: [  853]: --> [7:CONNECT]
oct 29 14:25:03.41: [  853]: <-- data [23]
oct 29 14:25:03.41: [  853]: <-- data [2]
oct 29 14:25:05.19: [  853]: --> [7:CONNECT]
oct 29 14:25:05.19: [  853]: <-- data [10]
oct 29 14:25:05.19: [  853]: <-- data [2]
oct 29 14:25:05.74: [  853]: --> [2:OK]
oct 29 14:25:05.74: [  853]: <-- [9:AT+FRH=3\r]
oct 29 14:25:08.84: [  853]: --> [0:]
oct 29 14:25:08.84: [  853]: MODEM <Empty line>
oct 29 14:25:08.84: [  853]: <-- data [1]
oct 29 14:25:08.90: [  853]: --> [2:OK]
oct 29 14:25:08.90: [  853]: DELAY 1500 ms
oct 29 14:25:10.40: [  853]: <-- [9:AT+FTH=3\r]
oct 29 14:25:10.47: [  853]: --> [7:CONNECT]
oct 29 14:25:10.47: [  853]: <-- data [23]
oct 29 14:25:10.47: [  853]: <-- data [2]
oct 29 14:25:12.24: [  853]: --> [7:CONNECT]
oct 29 14:25:12.24: [  853]: <-- data [10]
oct 29 14:25:12.24: [  853]: <-- data [2]
oct 29 14:25:12.79: [  853]: --> [2:OK]
oct 29 14:25:12.79: [  853]: <-- [9:AT+FRH=3\r]
oct 29 14:25:15.89: [  853]: --> [0:]
oct 29 14:25:15.89: [  853]: MODEM <Empty line>
oct 29 14:25:15.89: [  853]: <-- data [1]
oct 29 14:25:15.95: [  853]: --> [2:OK]
oct 29 14:25:15.95: [  853]: DELAY 1500 ms
oct 29 14:25:17.45: [  853]: <-- [9:AT+FTH=3\r]
oct 29 14:25:17.51: [  853]: --> [7:CONNECT]
oct 29 14:25:17.51: [  853]: <-- data [23]
oct 29 14:25:17.51: [  853]: <-- data [2]
oct 29 14:25:19.29: [  853]: --> [7:CONNECT]
oct 29 14:25:19.29: [  853]: <-- data [10]
oct 29 14:25:19.29: [  853]: <-- data [2]
oct 29 14:25:19.84: [  853]: --> [2:OK]
oct 29 14:25:19.84: [  853]: <-- [9:AT+FRH=3\r]
oct 29 14:25:22.94: [  853]: --> [0:]
oct 29 14:25:22.94: [  853]: MODEM <Empty line>
oct 29 14:25:22.94: [  853]: <-- data [1]
oct 29 14:25:22.99: [  853]: --> [2:OK]
oct 29 14:25:22.99: [  853]: DELAY 1500 ms
oct 29 14:25:24.49: [  853]: <-- [9:AT+FTH=3\r]
oct 29 14:25:24.55: [  853]: --> [7:CONNECT]
oct 29 14:25:24.55: [  853]: <-- data [23]
oct 29 14:25:24.55: [  853]: <-- data [2]
oct 29 14:25:26.33: [  853]: --> [7:CONNECT]
oct 29 14:25:26.33: [  853]: <-- data [10]
oct 29 14:25:26.33: [  853]: <-- data [2]
oct 29 14:25:26.88: [  853]: --> [2:OK]
oct 29 14:25:26.88: [  853]: <-- [9:AT+FRH=3\r]
oct 29 14:25:29.98: [  853]: --> [0:]
oct 29 14:25:29.98: [  853]: MODEM <Empty line>
oct 29 14:25:29.98: [  853]: <-- data [1]
oct 29 14:25:30.04: [  853]: --> [2:OK]
oct 29 14:25:30.04: [  853]: RECV FAX: No answer (T.30 T1 timeout)
oct 29 14:25:30.04: [  853]: RECV FAX: end
oct 29 14:25:30.04: [  853]: SESSION END