Re: [hylafax-users] No answer (T.30 T1 timeout)

[Y BAESA <ybaesa@xxxxxxxxxx>]

Good evening, 
You can use the files of config being under../hylafax/config usr-rts or
usr-xon 
I use usr-rts in etc/config.ttySx with identical modems on my server of
fax release (4.1.8) and that functions

Yves

Le mar 06/04/2004 à 13:11, Pignedoli Luca a écrit :
> Hi all,
> I have install Hylafax from the cvs server (i think is version 4.2.0)
> and i have configure modem with faxaddmodem. The modem is a U.S.
> Robotics 56K Faxmodem ext. and this is a config file:
> 
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType:              Class1          # use class 1 interface
> ModemRate:              19200           # rate for DCE-DTE communication
> ModemFlowControl:       xonxoff         # software flow control
> #
> ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
> ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
> (or not)
> ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
> ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
> control
> ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
> control
> ModemResultCodesCmd:    ATQ0X4          # enable result codes
> #
> ModemMfrQueryCmd:       !USR
> ModemModelQueryCmd:     ATI3
> ModemRevQueryCmd:       ATI7            # XXX returns a multi-line result
> #
> # When AT+FCLASS=1 is issued the modem automatically switches
> # to software flow control; these parameters let the fax software
> # reset flow control as needed after entering Class 1.
> #
> Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow control
> Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow
> control
> Class1SFLOCmd:          ""              # modem does this automatically
> #
> # This should resolve "DIS/DTC received 3 times" errors:
> #
> Class1ResponseWaitCmd:  AT+FRS=1        # wait after sending TCF for
> response
> #
> # The remainder of this configuration is included so that the
> # modem "idles" in Class 0 while not sending or receiving facsimile.
> #
> ModemSetupAACmd:        AT+FCLASS=0     # leave modem idling in class 0
> ModemAnswerCmd:         AT+FCLASS=1A    # answer in Class 1
> #
> # Disables the reporting of bad frames by the modem.  This
> # overcomes a firmware problem in the x2 and V90 Sportsters.
> # It is not necessary for the Courier modem.
> #
> Class2NRCmd:    AT+FNR=1,1,1,0
> 
> Every a lot i don't recived a fax whith error No answer (T.30 T1 timeout).
> 
> This is the log of Hylafax that I obtain:
> 
> Apr 06 11:15:28.45: [ 6197]: SESSION BEGIN 000004281 390522xxxxxx
> Apr 06 11:15:28.45: [ 6197]: HylaFAX (tm) Version 4.2.0
> Apr 06 11:15:28.45: [ 6197]: <-- [13:AT+FCLASS=1A\r]
> Apr 06 11:15:33.74: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:33.74: [ 6197]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
> Apr 06 11:15:33.74: [ 6197]: RECV FAX: begin
> Apr 06 11:15:33.74: [ 6197]: <-- data [32]
> Apr 06 11:15:33.74: [ 6197]: <-- data [2]
> Apr 06 11:15:33.81: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:33.81: [ 6197]: <-- data [23]
> Apr 06 11:15:33.81: [ 6197]: <-- data [2]
> Apr 06 11:15:34.53: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:34.53: [ 6197]: <-- data [10]
> Apr 06 11:15:34.53: [ 6197]: <-- data [2]
> Apr 06 11:15:36.71: [ 6197]: --> [2:OK]
> Apr 06 11:15:36.71: [ 6197]: <-- [9:AT+FRH=3\r]
> Apr 06 11:15:37.09: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:37.23: [ 6197]: --> [5:ERROR]
> Apr 06 11:15:37.23: [ 6197]: MODEM Command error
> Apr 06 11:15:37.23: [ 6197]: FCS error
> Apr 06 11:15:37.23: [ 6197]: DELAY 1500 ms
> Apr 06 11:15:38.73: [ 6197]: <-- [9:AT+FTH=3\r]
> Apr 06 11:15:38.93: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:38.93: [ 6197]: <-- data [32]
> Apr 06 11:15:38.93: [ 6197]: <-- data [2]
> Apr 06 11:15:39.09: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:39.09: [ 6197]: <-- data [23]
> Apr 06 11:15:39.09: [ 6197]: <-- data [2]
> Apr 06 11:15:39.81: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:39.81: [ 6197]: <-- data [10]
> Apr 06 11:15:39.81: [ 6197]: <-- data [2]
> Apr 06 11:15:42.00: [ 6197]: --> [2:OK]
> Apr 06 11:15:42.00: [ 6197]: <-- [9:AT+FRH=3\r]
> Apr 06 11:15:45.10: [ 6197]: --> [0:]
> Apr 06 11:15:45.10: [ 6197]: MODEM <Empty line>
> Apr 06 11:15:45.10: [ 6197]: <-- data [1]
> Apr 06 11:15:45.11: [ 6197]: --> [2:OK]
> Apr 06 11:15:45.11: [ 6197]: DELAY 1500 ms
> Apr 06 11:15:46.61: [ 6197]: <-- [9:AT+FTH=3\r]
> Apr 06 11:15:46.65: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:46.65: [ 6197]: <-- data [32]
> Apr 06 11:15:46.65: [ 6197]: <-- data [2]
> Apr 06 11:15:46.82: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:46.82: [ 6197]: <-- data [23]
> Apr 06 11:15:46.82: [ 6197]: <-- data [2]
> Apr 06 11:15:47.54: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:47.54: [ 6197]: <-- data [10]
> Apr 06 11:15:47.54: [ 6197]: <-- data [2]
> Apr 06 11:15:49.72: [ 6197]: --> [2:OK]
> Apr 06 11:15:49.72: [ 6197]: <-- [9:AT+FRH=3\r]
> Apr 06 11:15:52.82: [ 6197]: --> [0:]
> Apr 06 11:15:52.82: [ 6197]: MODEM <Empty line>
> Apr 06 11:15:52.82: [ 6197]: <-- data [1]
> Apr 06 11:15:52.83: [ 6197]: --> [2:OK]
> Apr 06 11:15:52.83: [ 6197]: DELAY 1500 ms
> Apr 06 11:15:54.33: [ 6197]: <-- [9:AT+FTH=3\r]
> Apr 06 11:15:54.37: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:54.37: [ 6197]: <-- data [32]
> Apr 06 11:15:54.37: [ 6197]: <-- data [2]
> Apr 06 11:15:54.53: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:54.53: [ 6197]: <-- data [23]
> Apr 06 11:15:54.53: [ 6197]: <-- data [2]
> Apr 06 11:15:55.25: [ 6197]: --> [7:CONNECT]
> Apr 06 11:15:55.25: [ 6197]: <-- data [10]
> Apr 06 11:15:55.25: [ 6197]: <-- data [2]
> Apr 06 11:15:57.44: [ 6197]: --> [2:OK]
> Apr 06 11:15:57.44: [ 6197]: <-- [9:AT+FRH=3\r]
> Apr 06 11:16:00.54: [ 6197]: --> [0:]
> Apr 06 11:16:00.54: [ 6197]: MODEM <Empty line>
> Apr 06 11:16:00.54: [ 6197]: <-- data [1]
> Apr 06 11:16:00.55: [ 6197]: --> [2:OK]
> Apr 06 11:16:00.55: [ 6197]: DELAY 1500 ms
> Apr 06 11:16:02.05: [ 6197]: <-- [9:AT+FTH=3\r]
> Apr 06 11:16:02.09: [ 6197]: --> [7:CONNECT]
> Apr 06 11:16:02.09: [ 6197]: <-- data [32]
> Apr 06 11:16:02.09: [ 6197]: <-- data [2]
> Apr 06 11:16:02.25: [ 6197]: --> [7:CONNECT]
> Apr 06 11:16:02.25: [ 6197]: <-- data [23]
> Apr 06 11:16:02.25: [ 6197]: <-- data [2]
> Apr 06 11:16:02.97: [ 6197]: --> [7:CONNECT]
> Apr 06 11:16:02.97: [ 6197]: <-- data [10]
> Apr 06 11:16:02.97: [ 6197]: <-- data [2]
> Apr 06 11:16:05.16: [ 6197]: --> [2:OK]
> Apr 06 11:16:05.16: [ 6197]: <-- [9:AT+FRH=3\r]
> Apr 06 11:16:08.26: [ 6197]: --> [0:]
> Apr 06 11:16:08.26: [ 6197]: MODEM <Empty line>
> Apr 06 11:16:08.26: [ 6197]: <-- data [1]
> Apr 06 11:16:08.27: [ 6197]: --> [2:OK]
> Apr 06 11:16:08.27: [ 6197]: DELAY 1500 ms
> Apr 06 11:16:09.77: [ 6197]: <-- [9:AT+FTH=3\r]
> Apr 06 11:16:09.81: [ 6197]: --> [7:CONNECT]
> Apr 06 11:16:09.81: [ 6197]: <-- data [32]
> Apr 06 11:16:09.81: [ 6197]: <-- data [2]
> Apr 06 11:16:09.98: [ 6197]: --> [7:CONNECT]
> Apr 06 11:16:09.98: [ 6197]: <-- data [23]
> Apr 06 11:16:09.98: [ 6197]: <-- data [2]
> Apr 06 11:16:10.70: [ 6197]: --> [7:CONNECT]
> Apr 06 11:16:10.70: [ 6197]: <-- data [10]
> Apr 06 11:16:10.70: [ 6197]: <-- data [2]
> Apr 06 11:16:12.88: [ 6197]: --> [2:OK]
> Apr 06 11:16:12.88: [ 6197]: <-- [9:AT+FRH=3\r]
> Apr 06 11:16:15.98: [ 6197]: --> [0:]
> Apr 06 11:16:15.98: [ 6197]: MODEM <Empty line>
> Apr 06 11:16:15.98: [ 6197]: <-- data [1]
> Apr 06 11:16:15.99: [ 6197]: --> [2:OK]
> Apr 06 11:16:15.99: [ 6197]: RECV FAX: No answer (T.30 T1 timeout)
> Apr 06 11:16:15.99: [ 6197]: RECV FAX: end
> Apr 06 11:16:15.99: [ 6197]: SESSION END
> 
> 
> Help me!
> 
> Thanks and sorry for my bad english :(.
> 
> 
> 
> 
> 
> ____________________ HylaFAX(tm) Users Mailing List _______________________
>   To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
>   *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
> 
> 


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*