Re: [hylafax-users] Is there something special about "10 pages" in outgoing fax jobs?

[An Intrepid HylaFax User <hylafax@xxxxxxxxx>]

> (apologies, but if you decide to grace us with your name, I'll know how
> to address you in the future ';-) )

Rob.

> Please repeat your tests without RTFCC or V.34 enabled by changing your
> config file to read:

I don't think I'm connecting at anything other than 14.4 with these
endpoints, but I'll try out what you suggest.

My comm-log excerpt is as follows: (tracing mode 0x4f)

Oct 13 03:22:49.59: [30801]: <-- [14:AT+FCLASS=2.1\r]
Oct 13 03:22:49.70: [30801]: --> [2:OK]
Oct 13 03:22:49.70: [30801]: <-- [9:AT+FLO=1\r]
Oct 13 03:22:49.81: [30801]: --> [2:OK]
Oct 13 03:22:49.81: [30801]: <-- [9:AT+FPP=0\r]
Oct 13 03:22:49.92: [30801]: --> [2:OK]
Oct 13 03:22:49.92: [30801]: <-- [9:AT+FBO=0\r]
Oct 13 03:22:50.03: [30801]: --> [2:OK]
Oct 13 03:22:50.03: [30801]: <-- [10:AT+FCT=30\r]
Oct 13 03:22:50.14: [30801]: --> [2:OK]
Oct 13 03:22:50.14: [30801]: <-- [11:AT+FCQ=1,0\r]
Oct 13 03:22:50.25: [30801]: --> [2:OK]
Oct 13 03:22:50.25: [30801]: <-- [15:AT+FNR=1,1,1,1\r]
Oct 13 03:22:50.36: [30801]: --> [2:OK]
Oct 13 03:22:50.36: [30801]: <-- [13:AT+FAP=1,1,1\r]
Oct 13 03:22:50.47: [30801]: --> [2:OK]
Oct 13 03:22:50.47: [30801]: <-- [9:AT+FIE=0\r]
Oct 13 03:22:50.58: [30801]: --> [2:OK]
Oct 13 03:22:50.58: [30801]: <-- [9:AT+FBU=1\r]
Oct 13 03:22:50.69: [30801]: --> [2:OK]
Oct 13 03:22:50.69: [30801]: <-- [23:AT+FCC=1,D,2,2,3,1,0,0\r]
Oct 13 03:22:50.80: [30801]: --> [2:OK]
Oct 13 03:22:50.80: [30801]: <-- [20:AT+FLI="DebtDomain"\r]
Oct 13 03:22:50.91: [30801]: --> [2:OK]
Oct 13 03:22:50.91: [30801]: DIAL 01165xxxxxxxx
Oct 13 03:22:50.91: [30801]: <-- [33:AT+FCC=,,,,,,,,0;DT01165xxxxxxxx\r]
Oct 13 03:23:09.24: [30801]: --> [47:+FHR:FF 03 20 00 00 56 55 55 00 8C 90
80 61 01 ]
Oct 13 03:23:09.24: [30801]: --> [4:+FCO]
Oct 13 03:23:09.24: [30801]: --> [37:+FNF:00 00 56 55 55 00 8C 90 80 61 01]
Oct 13 03:23:09.24: [30801]: REMOTE NSF "00 00 56 55 55 00 8C 90 80 61 01"
Oct 13 03:23:09.24: [30801]: NSF remote fax equipment: Brother 
Oct 13 03:23:09.94: [30801]: --> [74:+FHR:FF 03 40 xx xx xx xx xx xx xx xx
20 35 36 20 20 20 20 20 20 20 20 20 ]
Oct 13 03:23:09.94: [30801]: --> [27:+FCI:"         65 xxxxxxxx"]
Oct 13 03:23:09.94: [30801]: REMOTE CSI "65 xxxxxxxx"
Oct 13 03:23:10.25: [30801]: --> [32:+FHR:FF 13 80 00 EE A8 C4 80 11 ]
Oct 13 03:23:10.25: [30801]: --> [22:+FIS:3,5,0,2,3,1,0,3,0]
Oct 13 03:23:10.25: [30801]: --> [2:OK]
Oct 13 03:23:10.25: [30801]: REMOTE best rate 14400 bit/s
Oct 13 03:23:10.25: [30801]: REMOTE max page width 1728 pixels in 215 mm
Oct 13 03:23:10.25: [30801]: REMOTE max unlimited page length
Oct 13 03:23:10.25: [30801]: REMOTE best vres 7.7 line/mm
Oct 13 03:23:10.25: [30801]: REMOTE best format 2-D MMR
Oct 13 03:23:10.25: [30801]: REMOTE supports T.30 Annex A, ECM
Oct 13 03:23:10.25: [30801]: REMOTE best 10 ms/scanline
Oct 13 03:23:10.25: [30801]: USE 14400 bit/s
Oct 13 03:23:10.25: [30801]: USE 10 ms/scanline
Oct 13 03:23:10.25: [30801]: USE error correction mode
Oct 13 03:23:10.25: [30801]: SEND file "docq/doc317.ps;c0"
Oct 13 03:23:10.25: [30801]: USE page width 1728 pixels in 215 mm
Oct 13 03:23:10.25: [30801]: USE unlimited page length
Oct 13 03:23:10.25: [30801]: USE 3.85 line/mm
Oct 13 03:23:10.25: [30801]: USE 2-D MMR
Oct 13 03:23:10.25: [30801]: <-- [23:AT+FIS=0,5,0,2,3,1,0,3\r]
Oct 13 03:23:10.36: [30801]: --> [2:OK]
Oct 13 03:23:10.36: [30801]: <-- [7:AT+FDT\r]
Oct 13 03:23:11.50: [30801]: --> [74:+FHT:FF 03 43 20 20 20 20 20 20 20 20
20 20 6E 69 61 6D 6F 44 74 62 65 44 ]
Oct 13 03:23:11.50: [30801]: --> [44:+FHT:FF 13 83 00 22 F8 C4 80 80 80 80
80 00 ]
Oct 13 03:23:17.82: [30801]: --> [14:+FHR:FF 13 84 ]
Oct 13 03:23:17.82: [30801]: --> [22:+FCS:0,5,0,2,3,1,0,0,0]
Oct 13 03:23:17.82: [30801]: --> [7:CONNECT]
Oct 13 03:23:17.82: [30801]: Enable Real-Time Fax Compression Conversion
Oct 13 03:23:17.82: [30801]: Reading MMR-compressed image file
Oct 13 03:23:17.82: [30801]: <-- data [2]
Oct 13 03:23:17.82: [30801]: SEND begin page

(this goes for 10 pages without incident or problem until...)

Oct 13 03:26:54.58: [30801]: SENT 23557 bytes of data
Oct 13 03:26:54.58: [30801]: SEND 2D RTC
Oct 13 03:26:54.58: [30801]: <-- data [10]
Oct 13 03:26:54.58: [30801]: MODEM set XON/XOFF/DRAIN: input interpreted,
output generated
Oct 13 03:26:55.24: [30801]: SEND end page
Oct 13 03:26:55.24: [30801]: SEND send MPS (more pages, same document)
Oct 13 03:26:55.24: [30801]: <-- data [2]
Oct 13 03:27:17.89: [30801]: --> [7:+FHS:52]
Oct 13 03:27:17.89: [30801]: REMOTE HANGUP: No response to MPS repeated 3
times (code 52)
Oct 13 03:27:17.89: [30801]: <-- [5:ATH0\r]
Oct 13 03:27:17.89: [30801]: --> [2:OK]
Oct 13 03:27:17.89: [30801]: MODEM set DTR OFF

> Class2RTFCC:            no   # my modem reports non-zero data to this
> but I'm too scared to use it

Cute. :)

What is RTFCC?

> and restarting faxgetty, and let us know how you fare.

OK, I'll need to get a copy of that PDF file which is being blasted out... 
And I can test it properly.

Is there a "concealed" MaxSENDPages setting in HylaFax I've stumbled across?
 I've included the following line into both my /var/spool/hylafax/etc/config
and config.modem files:

MaxSendPages:           99

Grepping through source code found some references to a setting that the
code retrieves, but I didn't find anything in either the FAQ or the official
documentation.

Wow, you're prowling these mailing lists late, Darren. :)

=R=



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*