[hylafax-users] Troubles with Multitech ISI5634PCI-8

[Andrea Nicolini <andrea@xxxxxxxxx>]

Hi,

Unfortunately I'm still having troubles with ISI5634PCI-8 on Hylafax.
This is quite strange since the configuration I'm using is in Class1,
the firmware is updated and the Hylafax config file explicitly report my board model.

Is there anybody out there using this board succesfully???

I'm using 2 boards and I noticed that they're sharing the same irq (5), 
can this cause troubles? 

Here is the config file:
...
...
ModemType:              Class1          # use this to supply a hint
Class1TCFRecvHack:      yes             # avoid +FCERROR before TCF
ModemRate:              19200           
ModemFlowControl:       rtscts
# Class1MsgRecvHackCmd: AT+FRS=1        # avoid +FCERROR before image

# If your line supports Caller-ID, you may want to uncomment this...
# QualifyCID:           etc/cid         # you must create this file
# ModemResetCmds:       AT+VCID=1       
# CIDNumber:            "NMBR="
# CIDName:              "NAME="

# Or with the MT5634ZBA-DID you'll probably need something like...
# QualifyCID:           etc/cid         # you must create this file
# ModemResetCmds:       AT*DS1*DD0*DF1  # enable DTMF-DID 
# CIDNumber:            "DTMF"          # format of AT*DF1
# CIDNumberAnswerLength:        4       # four DTMF-DID digits then ATA
#

I also tried to configure the modem in class 1.0,2,2.0,2.1 but with no
satisfactory results.
In class 1 the most frequent error is a corruption of the received faxes
and a "T.30 T2 timeout, expected page not received" error.


Sep 26 15:19:53.19: [29287]: SESSION BEGIN 00006788 3xxxxxxxx
Sep 26 15:19:53.19: [29287]: HylaFAX (tm) Version 4.1.7
Sep 26 15:19:53.19: [29287]: <-- [4:ATA\r]
Sep 26 15:20:04.65: [29287]: --> [7:CONNECT]
Sep 26 15:20:04.65: [29287]: ANSWER: FAX CONNECTION  DEVICE
'/dev/ttyM1e'
Sep 26 15:20:04.65: [29287]: RECV FAX: begin
Sep 26 15:20:04.66: [29287]: <-- data [23]
Sep 26 15:20:04.66: [29287]: <-- data [2]
Sep 26 15:20:04.71: [29287]: --> [7:CONNECT]
Sep 26 15:20:04.71: [29287]: <-- data [10]
Sep 26 15:20:04.71: [29287]: <-- data [2]
Sep 26 15:20:05.96: [29287]: --> [2:OK]
Sep 26 15:20:05.96: [29287]: <-- [9:AT+FRH=3\r]
Sep 26 15:20:06.82: [29287]: --> [7:CONNECT]
Sep 26 15:20:08.07: [29287]: --> [2:OK]
Sep 26 15:20:08.07: [29287]: REMOTE wants 9600 bit/s
Sep 26 15:20:08.07: [29287]: REMOTE wants page width 1728 pixels in 215
mm
Sep 26 15:20:08.07: [29287]: REMOTE wants unlimited page length
Sep 26 15:20:08.07: [29287]: REMOTE wants 3.85
line/mm                          Sep 26 15:20:08.07: [29287]: REMOTE
wants 2-D MR
Sep 26 15:20:08.07: [29287]: <-- [9:AT+FRH=3\r]
Sep 26 15:20:08.13: [29287]: --> [7:CONNECT]Sep 26 15:20:08.13: [29287]:
--> [10:NO CARRIER]
Sep 26 15:20:08.13: [29287]: RECV training at v.29 9600 bit/s
Sep 26 15:20:08.13: [29287]: <-- [10:AT+FRM=96\r]
Sep 26 15:20:08.42: [29287]: --> [7:CONNECT]
Sep 26 15:20:09.96: [29287]: RECV: TCF 1824 bytes, 0% non-zero, 1823
zero-run
Sep 26 15:20:09.96: [29287]: --> [10:NO CARRIER]
Sep 26 15:20:09.96: [29287]: DELAY 75 ms
Sep 26 15:20:10.04: [29287]: TRAINING succeeded
Sep 26 15:20:10.05: [29287]: <-- [9:AT+FTH=3\r]
Sep 26 15:20:11.06: [29287]: --> [7:CONNECT]
Sep 26 15:20:11.06: [29287]: <-- data [3]
Sep 26 15:20:11.06: [29287]: <-- data [2]
Sep 26 15:20:11.50: [29287]: --> [2:OK]
Sep 26 15:20:11.50: [29287]: <-- [10:AT+FRM=96\r]
Sep 26 15:20:11.96: [29287]: --> [7:CONNECT]
Sep 26 15:20:11.96: [29287]: RECV: begin page
Sep 26 15:20:11.96: [29287]: RECV: 0 total lines, 0 bad lines, 0
consecutive bad lines
Sep 26 15:20:11.96: [29287]: RECV: end page
Sep 26 15:20:11.96: [29287]: --> [10:NO CARRIER]
Sep 26 15:20:11.96: [29287]: <-- [9:AT+FRH=3\r]
Sep 26 15:20:12.48: [29287]: --> [7:CONNECT]
Sep 26 15:20:17.48: [29287]: <-- data [1]

Sep 26 15:20:08.13: [29287]: --> [2:^P^C]

Sep 26 15:20:17.54: [29287]: --> [2:OK]
Sep 26 15:20:17.54: [29287]: RECV keeping unconfirmed page
Sep 26 15:20:17.54: [29287]: RECV FAX (00006788): from <UNSPECIFIED>,
page 1 in 0:07, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Sep 26 15:20:17.54: [29287]: RECV FAX (00006788): recvq/fax03626.tif
from <UNSPECIFIED>, route to <unspecified>, 1 pages in 0:13
Sep 26 15:20:17.55: [29287]: RECV FAX: T.30 T2 timeout, expected page
not received
Sep 26 15:20:17.55: [29287]: <-- [9:AT+FTH=3\r]
Sep 26 15:20:18.56: [29287]: --> [7:CONNECT]
Sep 26 15:20:18.56: [29287]: <-- data [3]
Sep 26 15:20:18.56: [29287]: <-- data [2]
Sep 26 15:20:19.00: [29287]: --> [2:OK]
Sep 26 15:20:19.00: [29287]: RECV FAX (00006788): session with
<UNSPECIFIED> terminated abnormally: T.30 T2 timeout, expected page not
received
Sep 26 15:20:19.00: [29287]: RECV FAX: bin/faxrcvd "recvq/fax03626.tif"
"ttyM1e" "00006788" "T.30 T2 timeout, expected page not received" "" ""
Sep 26 15:20:21.87: [29287]: RECV FAX: end
Sep 26 15:20:21.87: [29287]: SESSION END

Thank you in advance.
Bye.

-- 

Andrea Nicolini
andrea@xxxxxxxxx
http://www.teamsw.it
Team Software S.r.l.
Via Campagna 30
Cognento MO
Tel 059.343790
Fax 059.341576
Personal Homepage:
http://digilander.iol.it/aser76


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*