Re: [hylafax-users] Problem receiving fax: possibly timeout issue?

[Ali.Naddaf@trilogy.com]

Lee,
Thanks for your suggestion. I followed your advice and added that to my 
config.ttyS4 but still I am seeing the same problem. Here is my new log 
file:

Jul 19 01:36:11.19: [ 9048]: SESSION BEGIN 00000031 15125551212
Jul 19 01:36:11.19: [ 9048]: HylaFAX (tm) Version 4.1.5
Jul 19 01:36:11.19: [ 9048]: MODEM set XON/XOFF/FLUSH: input ignored, 
output disabled
Jul 19 01:36:11.19: [ 9048]: <-- [4:ATA\r]
Jul 19 01:36:17.32: [ 9048]: --> [7:CONNECT]
Jul 19 01:36:17.32: [ 9048]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS4'
Jul 19 01:36:17.32: [ 9048]: STATE CHANGE: ANSWERING -> RECEIVING
Jul 19 01:36:17.32: [ 9048]: MODEM input buffering enabled
Jul 19 01:36:17.32: [ 9048]: RECV FAX: begin
Jul 19 01:36:17.32: [ 9048]: RECV FAX: CDPN 
Jul 19 01:36:17.32: [ 9048]: MODEM input buffering disabled
Jul 19 01:36:17.32: [ 9048]: <-- HDLC<23:FF C0 02 0E AE 2E A6 CA E6 76 96 
16 2E F6 72 04 04 04 04 04 04 04 04>
Jul 19 01:36:17.32: [ 9048]: <-- data [23]
Jul 19 01:36:17.32: [ 9048]: <-- data [2]
Jul 19 01:36:17.33: [ 9048]: --> [7:CONNECT]
Jul 19 01:36:17.33: [ 9048]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Jul 19 01:36:17.33: [ 9048]: <-- data [10]
Jul 19 01:36:17.33: [ 9048]: <-- data [2]
Jul 19 01:36:18.54: [ 9048]: --> [2:OK]
Jul 19 01:36:18.54: [ 9048]: <-- [9:AT+FRH=3\r]
Jul 19 01:36:18.80: [ 9048]: --> [7:CONNECT]
Jul 19 01:36:20.53: [ 9048]: --> HDLC<25:FF C0 C2 CE CE A6 4E 0A F6 66 76 
92 04 04 04 04 04 04 04 04 04 04 04 D7 3A>
Jul 19 01:36:20.53: [ 9048]: --> [2:OK]
Jul 19 01:36:20.53: [ 9048]: REMOTE TSI "InfoPress"
Jul 19 01:36:20.53: [ 9048]: <-- [9:AT+FRH=3\r]
Jul 19 01:36:20.54: [ 9048]: --> [7:CONNECT]
Jul 19 01:36:20.80: [ 9048]: --> HDLC<8:FF C8 C1 00 47 1E 36 71>
Jul 19 01:36:20.80: [ 9048]: --> [2:OK]
Jul 19 01:36:20.80: [ 9048]: REMOTE wants 14400 bit/s
Jul 19 01:36:20.80: [ 9048]: REMOTE wants page width 1728 pixels in 215 mm
Jul 19 01:36:20.80: [ 9048]: REMOTE wants unlimited page length 
Jul 19 01:36:20.80: [ 9048]: REMOTE wants 7.7 line/mm
Jul 19 01:36:20.80: [ 9048]: REMOTE wants 2-D MR
Jul 19 01:36:20.80: [ 9048]: <-- [9:AT+FRH=3\r]
Jul 19 01:36:20.81: [ 9048]: --> [7:CONNECT]
Jul 19 01:36:20.89: [ 9048]: --> [2:OK]
Jul 19 01:36:50.89: [ 9048]: MODEM TIMEOUT: reading line from modem
Jul 19 01:36:50.89: [ 9048]: MODEM <Timeout>
Jul 19 01:36:50.89: [ 9048]: RECV training at v.17 14400 bit/s
Jul 19 01:36:50.89: [ 9048]: MODEM set XON/XOFF/DRAIN: input ignored, 
output generated
Jul 19 01:36:50.89: [ 9048]: <-- [11:AT+FRM=145\r]
Jul 19 01:36:55.39: [ 9048]: --> [0:]
Jul 19 01:36:55.39: [ 9048]: MODEM <Empty line>
Jul 19 01:36:55.39: [ 9048]: MODEM TIMEOUT: receiving TCF
Jul 19 01:36:55.39: [ 9048]: <-- data [1]
Jul 19 01:36:55.40: [ 9048]: --> [2:]
Jul 19 01:36:55.40: [ 9048]: --> [2:OK]
Jul 19 01:36:55.40: [ 9048]: MODEM set XON/XOFF/DRAIN: input ignored, 
output disabled
Jul 19 01:36:55.40: [ 9048]: DELAY 75 ms
Jul 19 01:36:55.48: [ 9048]: <-- [9:AT+FTH=3\r]
Jul 19 01:36:56.34: [ 9048]: --> [7:CONNECT]
Jul 19 01:36:56.34: [ 9048]: <-- HDLC<3:FF C8 22>
Jul 19 01:36:56.34: [ 9048]: <-- data [3]
Jul 19 01:36:56.34: [ 9048]: <-- data [2]
Jul 19 01:36:56.66: [ 9048]: --> [2:OK]
Jul 19 01:36:56.66: [ 9048]: TRAINING failed
Jul 19 01:36:56.66: [ 9048]: <-- [9:AT+FRH=3\r]
Jul 19 01:37:03.65: [ 9048]: --> [0:]
Jul 19 01:37:03.65: [ 9048]: MODEM <Empty line>
Jul 19 01:37:03.65: [ 9048]: MODEM TIMEOUT: waiting for v.21 carrier
Jul 19 01:37:03.65: [ 9048]: <-- data [1]
Jul 19 01:37:03.66: [ 9048]: --> [2:]
Jul 19 01:37:03.66: [ 9048]: --> [2:OK]
Jul 19 01:37:03.66: [ 9048]: RECV FAX: Failure to train modems
Jul 19 01:37:03.66: [ 9048]: RECV FAX: end
Jul 19 01:37:03.66: [ 9048]: SESSION END

Thanks,
Ali.





Lee Howard <faxguy@howardsilvan.com>
07/19/2003 01:15 AM

 
        To:     Ali.Naddaf@trilogy.com
        cc:     hylafax-users@hylafax.org
        Subject:        Re: [hylafax-users] Problem receiving fax: possibly timeout issue?


On 2003.07.18 22:54 Ali.Naddaf@trilogy.com wrote:
> Hello everyone.
> 
> I just installed HylaFax 4.1.5 on my SuSE 8.2. I have a Zoom/FaxModem
> 56K
> V.90 PCI modem (model 2920).

....

> Jul 19 00:15:35.88: [ 9048]: REMOTE wants 2-D MR
> Jul 19 00:15:35.88: [ 9048]: <-- [9:AT+FRH=3\r]
> Jul 19 00:15:35.89: [ 9048]: --> [7:CONNECT]
> Jul 19 00:15:35.97: [ 9048]: --> [2:OK]
> Jul 19 00:16:05.96: [ 9048]: MODEM TIMEOUT: reading line from modem

Turn Class1TCFRecvHack to "no" in your config file.  It was a "bad" 
default option in 4.1.5.

Lee.




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*