[hylafax-users] Faxes not received properly; no error messages

[Toralf Lund <toralf@procaptura.com>]

My hylafax installation - version 4.1.2 on SGI IRIX - has suddenly stopped 
receiving faxes properly. It will answer incoming calls as expected, and 
also create the output file, but before actual data is written, the 
sending fax will exit with "communication error" and hang up - or maybe 
hylafax disconnects first, it's a bit hard to tell. In any case, I'm left 
with a 8-byte TIFF file and a log file that doesn't really tell me 
anything; an example is attached. This appears to happen for faxes from 
several different senders. The setup has been running without any major 
problems since I last upgraded the software, which I did about a year ago, 
and I haven't touched the config since then (not consciously, anyway...)

Ideas, anyone?
--
- Toralf
May 28 10:10:13.07: [8288003]: SESSION BEGIN 00000506 4766855101
May 28 10:10:13.07: [8288003]: HylaFAX (tm) Version 4.1.2
May 28 10:10:13.07: [8288003]: <-- [18:AT+FCLASS=2.0;ATA\r]
May 28 10:10:22.85: [8288003]: --> [4:+FCO]
May 28 10:10:22.85: [8288003]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyd2'
May 28 10:10:22.85: [8288003]: RECV FAX: begin
May 28 10:10:24.51: [8288003]: --> [27:+FTI:"          4766855101"]
May 28 10:10:24.51: [8288003]: REMOTE TSI "4766855101"
May 28 10:10:24.84: [8288003]: --> [20:+FCS:0,3,0,2,0,0,0,0]
May 28 10:10:24.85: [8288003]: REMOTE wants 9600 bit/s
May 28 10:10:24.85: [8288003]: REMOTE wants page width 1728 pixels in 215 mm
May 28 10:10:24.85: [8288003]: REMOTE wants unlimited page length 
May 28 10:10:24.85: [8288003]: REMOTE wants 3.85 line/mm
May 28 10:10:24.85: [8288003]: REMOTE wants 1-D MR
May 28 10:10:24.95: [8288003]: --> [2:OK]
May 28 10:10:24.96: [8288003]: <-- [7:AT+FDR\r]
May 28 10:10:27.05: [8288003]: --> [20:+FCS:0,3,0,2,0,0,0,0]
May 28 10:10:27.05: [8288003]: REMOTE wants 9600 bit/s
May 28 10:10:27.05: [8288003]: REMOTE wants page width 1728 pixels in 215 mm
May 28 10:10:27.05: [8288003]: REMOTE wants unlimited page length 
May 28 10:10:27.05: [8288003]: REMOTE wants 3.85 line/mm
May 28 10:10:27.05: [8288003]: REMOTE wants 1-D MR
May 28 10:10:28.87: [8288003]: --> [7:CONNECT]
May 28 10:10:28.87: [8288003]: RECV: begin page
May 28 10:10:28.87: [8288003]: RECV: send trigger 022
May 28 10:10:28.87: [8288003]: <-- data [1]