[hylafax-users] failed training modem

["peter" <peter@oa-systems.nl>]

hello, i red more about this topic but i couldnt find a good explanation for
my error.

i have newest hylafax  (4.1.5) on a redhat 8.0 box kernel 2.4.18-14

Modem that i have is

Communication controller: Rockwell International HCF 56k Data/Fax Modem (rev
01)
        Subsystem: GVC Corporation IBM F-1156IV+/R6 WW V.90 Modem
        Flags: bus master, medium devsel, latency 32, IRQ 5
        Memory at e8000000 (32-bit, non-prefetchable) [size=64K]
        I/O ports at e400 [size=8]
        Capabilities: [40] Power Management version 2


     when i do the faxaddmodem command i can add the modem without a problem

..

here is the log of hylafax when a fax is not sended

less c00000024
Apr 10 12:23:55.46: [ 2811]: SESSION BEGIN 00000024 31740527251199
Apr 10 12:23:55.46: [ 2811]: HylaFAX (tm) Version 4.1.5
Apr 10 12:23:55.46: [ 2811]: SEND FAX: JOB 14 DEST 0527251199 COMMID
00000024 DEVICE '/dev/modem'
Apr 10 12:23:55.46: [ 2811]: DELAY 75 ms
Apr 10 12:23:55.57: [ 2811]: DELAY 2600 ms
Apr 10 12:23:58.17: [ 2811]: DELAY 10 ms
Apr 10 12:23:58.18: [ 2811]: <-- [4:ATZ\r]
Apr 10 12:23:58.62: [ 2811]: --> [2:OK]
Apr 10 12:23:58.62: [ 2811]: DELAY 3000 ms
Apr 10 12:24:01.62: [ 2811]: <-- [5:ATE0\r]
Apr 10 12:24:01.66: [ 2811]: --> [4:ATE0]
Apr 10 12:24:01.66: [ 2811]: --> [2:OK]
Apr 10 12:24:01.66: [ 2811]: <-- [5:ATV1\r]
Apr 10 12:24:01.70: [ 2811]: --> [2:OK]
Apr 10 12:24:01.70: [ 2811]: <-- [5:ATQ0\r]
Apr 10 12:24:01.74: [ 2811]: --> [2:OK]
Apr 10 12:24:01.74: [ 2811]: <-- [7:ATS0=0\r]
Apr 10 12:24:01.78: [ 2811]: --> [2:OK]
Apr 10 12:24:01.78: [ 2811]: <-- [7:ATS8=2\r]
Apr 10 12:24:01.82: [ 2811]: --> [2:OK]
Apr 10 12:24:01.82: [ 2811]: <-- [8:ATS7=60\r]
Apr 10 12:24:01.86: [ 2811]: --> [2:OK]
Apr 10 12:24:01.86: [ 2811]: <-- [6:AT&K3\r]
Apr 10 12:24:01.90: [ 2811]: --> [2:OK]
Apr 10 12:24:01.90: [ 2811]: <-- [6:AT&D2\r]
Apr 10 12:24:01.94: [ 2811]: --> [2:OK]
Apr 10 12:23:55.46: [ 2811]: SESSION BEGIN 00000024 31740527251199
Apr 10 12:23:55.46: [ 2811]: HylaFAX (tm) Version 4.1.5
Apr 10 12:23:55.46: [ 2811]: SEND FAX: JOB 14 DEST 0527251199 COMMID
00000024 DEVICE '/dev/modem'
Apr 10 12:23:55.46: [ 2811]: DELAY 75 ms
Apr 10 12:23:55.57: [ 2811]: DELAY 2600 ms
Apr 10 12:23:58.17: [ 2811]: DELAY 10 ms
Apr 10 12:23:58.18: [ 2811]: <-- [4:ATZ\r]
Apr 10 12:23:58.62: [ 2811]: --> [2:OK]
Apr 10 12:23:58.62: [ 2811]: DELAY 3000 ms
Apr 10 12:24:01.62: [ 2811]: <-- [5:ATE0\r]
Apr 10 12:24:01.66: [ 2811]: --> [4:ATE0]
Apr 10 12:24:01.66: [ 2811]: --> [2:OK]
Apr 10 12:24:01.66: [ 2811]: <-- [5:ATV1\r]
Apr 10 12:24:01.70: [ 2811]: --> [2:OK]
Apr 10 12:24:01.70: [ 2811]: <-- [5:ATQ0\r]
Apr 10 12:24:01.74: [ 2811]: --> [2:OK]
Apr 10 12:24:01.74: [ 2811]: <-- [7:ATS0=0\r]
Apr 10 12:24:01.78: [ 2811]: --> [2:OK]
Apr 10 12:24:01.78: [ 2811]: <-- [7:ATS8=2\r]
Apr 10 12:24:01.82: [ 2811]: --> [2:OK]
Apr 10 12:24:01.82: [ 2811]: <-- [8:ATS7=60\r]
Apr 10 12:24:01.86: [ 2811]: --> [2:OK]
Apr 10 12:24:01.86: [ 2811]: <-- [6:AT&K3\r]
Apr 10 12:24:01.90: [ 2811]: --> [2:OK]
Apr 10 12:24:01.90: [ 2811]: <-- [6:AT&D2\r]
Apr 10 12:24:01.94: [ 2811]: --> [2:OK]
Apr 10 12:24:01.94: [ 2811]: <-- [6:AT&C1\r]
Apr 10 12:24:01.98: [ 2811]: --> [2:OK]
Apr 10 12:24:01.98: [ 2811]: <-- [12:AT+FCLASS=1\r]
Apr 10 12:24:02.01: [ 2811]: --> [2:OK]
Apr 10 12:24:02.01: [ 2811]: <-- [5:ATM0\r]
Apr 10 12:24:02.05: [ 2811]: --> [2:OK]
Apr 10 12:24:02.05: [ 2811]: <-- [12:AT+FCLASS=1\r]
Apr 10 12:24:02.19: [ 2811]: --> [2:OK]
Apr 10 12:24:02.19: [ 2811]: DIAL 0527251199
Apr 10 12:24:02.19: [ 2811]: <-- [15:ATDT0527251199\r]
Apr 10 12:24:31.52: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:32.24: [ 2811]: --> [2:OK]
Apr 10 12:24:32.24: [ 2811]: REMOTE NSF "86 00 A2 00 00 81 00 B1"
Apr 10 12:24:32.24: [ 2811]: NSF remote fax equipment: unknown
Apr 10 12:24:32.24: [ 2811]: <-- [9:AT+FRH=3\r]
Apr 10 12:24:32.30: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:32.96: [ 2811]: --> [2:OK]
Apr 10 12:24:32.96: [ 2811]: REMOTE CSI "+31527251199"
Apr 10 12:24:32.96: [ 2811]: <-- [9:AT+FRH=3\r]
Apr 10 12:24:33.02: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:33.30: [ 2811]: --> [2:OK]
Apr 10 12:24:33.30: [ 2811]: REMOTE best rate 9600 bit/s
Apr 10 12:24:33.30: [ 2811]: REMOTE max page width 1728 pixels in 215 mm
Apr 10 12:24:33.30: [ 2811]: REMOTE max unlimited page length
Apr 10 12:24:33.30: [ 2811]: REMOTE best vres 7.7 line/mm
Apr 10 12:24:33.30: [ 2811]: REMOTE best format 2-D MMR
Apr 10 12:24:33.30: [ 2811]: REMOTE supports T.30 Annex A, ECM
Apr 10 12:24:33.30: [ 2811]: REMOTE best 10 ms, 5 ms/scanline
Apr 10 12:24:33.30: [ 2811]: USE 9600 bit/s
Apr 10 12:24:33.30: [ 2811]: USE 10 ms, 5 ms/scanline
Apr 10 12:24:33.30: [ 2811]: SEND file "docq/doc17.ps;01"
Apr 10 12:24:33.30: [ 2811]: USE page width 1728 pixels in 215 mm
Apr 10 12:24:33.30: [ 2811]: USE unlimited page length
Apr 10 12:24:33.30: [ 2811]: USE 7.7 line/mm
Apr 10 12:24:33.30: [ 2811]: USE 1-D MR
Apr 10 12:24:33.30: [ 2811]: SEND training at v.29 9600 bit/s
Apr 10 12:24:33.30: [ 2811]: <-- [9:AT+FTH=3\r]
Apr 10 12:24:33.73: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:33.73: [ 2811]: <-- data [23]
Apr 10 12:24:33.73: [ 2811]: <-- data [2]
Apr 10 12:24:35.39: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:35.39: [ 2811]: <-- data [6]
Apr 10 12:24:35.39: [ 2811]: <-- data [2]
Apr 10 12:24:35.91: [ 2811]: --> [2:OK]
Apr 10 12:24:35.91: [ 2811]: <-- [9:AT+FTS=7\r]
Apr 10 12:24:36.09: [ 2811]: --> [2:OK]
Apr 10 12:24:36.09: [ 2811]: <-- [10:AT+FTM=96\r]
Apr 10 12:24:36.15: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:36.15: [ 2811]: <-- data [1024]
Apr 10 12:24:36.15: [ 2811]: <-- data [776]
Apr 10 12:24:36.15: [ 2811]: <-- data [2]
Apr 10 12:24:38.30: [ 2811]: --> [2:OK]
Apr 10 12:24:38.30: [ 2811]: <-- [9:AT+FRH=3\r]
Apr 10 12:24:38.57: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:39.63: [ 2811]: --> [2:OK]
Apr 10 12:24:39.63: [ 2811]: SEND training at v.29 7200 bit/s
Apr 10 12:24:39.63: [ 2811]: <-- [9:AT+FTH=3\r]
Apr 10 12:24:40.06: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:40.06: [ 2811]: <-- data [23]
Apr 10 12:24:40.06: [ 2811]: <-- data [2]
Apr 10 12:24:41.76: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:41.76: [ 2811]: <-- data [6]
Apr 10 12:24:41.76: [ 2811]: <-- data [2]
Apr 10 12:24:42.26: [ 2811]: --> [2:OK]
Apr 10 12:24:42.26: [ 2811]: <-- [9:AT+FTS=7\r]
Apr 10 12:24:42.44: [ 2811]: --> [2:OK]
Apr 10 12:24:42.44: [ 2811]: <-- [10:AT+FTM=72\r]
Apr 10 12:24:42.50: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:42.50: [ 2811]: <-- data [1024]
Apr 10 12:24:42.50: [ 2811]: <-- data [326]
Apr 10 12:24:42.50: [ 2811]: <-- data [2]
Apr 10 12:24:44.63: [ 2811]: --> [2:OK]
Apr 10 12:24:44.63: [ 2811]: <-- [9:AT+FRH=3\r]
Apr 10 12:24:44.92: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:45.96: [ 2811]: --> [2:OK]
Apr 10 12:24:45.96: [ 2811]: SEND training at v.27ter 4800 bit/s
Apr 10 12:24:45.96: [ 2811]: <-- [9:AT+FTH=3\r]
Apr 10 12:24:46.39: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:46.39: [ 2811]: <-- data [23]
Apr 10 12:24:46.39: [ 2811]: <-- data [2]
Apr 10 12:24:48.07: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:48.07: [ 2811]: <-- data [6]
Apr 10 12:24:48.07: [ 2811]: <-- data [2]
Apr 10 12:24:48.59: [ 2811]: --> [2:OK]
Apr 10 12:24:48.59: [ 2811]: <-- [9:AT+FTS=7\r]
Apr 10 12:24:48.77: [ 2811]: --> [2:OK]
Apr 10 12:24:48.77: [ 2811]: <-- [10:AT+FTM=48\r]
Apr 10 12:24:48.83: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:48.83: [ 2811]: <-- data [900]
Apr 10 12:24:48.83: [ 2811]: <-- data [2]
Apr 10 12:24:51.44: [ 2811]: --> [2:OK]
Apr 10 12:24:51.44: [ 2811]: <-- [9:AT+FRH=3\r]
Apr 10 12:24:51.73: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:52.79: [ 2811]: --> [2:OK]
Apr 10 12:24:52.79: [ 2811]: SEND training at v.27ter fallback mode 2400
bit/s
Apr 10 12:24:52.79: [ 2811]: <-- [9:AT+FTH=3\r]
Apr 10 12:24:53.18: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:53.18: [ 2811]: <-- data [23]
Apr 10 12:24:53.18: [ 2811]: <-- data [2]
Apr 10 12:24:54.86: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:54.86: [ 2811]: <-- data [6]
Apr 10 12:24:54.86: [ 2811]: <-- data [2]
Apr 10 12:24:55.38: [ 2811]: --> [2:OK]
Apr 10 12:24:55.38: [ 2811]: <-- [9:AT+FTS=7\r]
Apr 10 12:24:55.56: [ 2811]: --> [2:OK]
Apr 10 12:24:55.56: [ 2811]: <-- [10:AT+FTM=24\r]
Apr 10 12:24:55.63: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:55.63: [ 2811]: <-- data [450]
Apr 10 12:24:55.63: [ 2811]: <-- data [2]
Apr 10 12:24:58.50: [ 2811]: --> [2:OK]
Apr 10 12:24:58.50: [ 2811]: <-- [9:AT+FRH=3\r]
Apr 10 12:24:58.79: [ 2811]: --> [7:CONNECT]
Apr 10 12:24:59.83: [ 2811]: --> [2:OK]
Apr 10 12:24:59.83: [ 2811]: TRAINING failed
Apr 10 12:24:59.83: [ 2811]: <-- [9:AT+FTH=3\r]
Apr 10 12:25:00.26: [ 2811]: --> [7:CONNECT]
Apr 10 12:25:00.28: [ 2811]: <-- data [3]
Apr 10 12:25:00.28: [ 2811]: <-- data [2]
Apr 10 12:25:01.64: [ 2811]: --> [2:OK]
Apr 10 12:25:01.64: [ 2811]: <-- [5:ATH0\r]
Apr 10 12:25:02.86: [ 2811]: --> [2:OK]
Apr 10 12:25:02.86: [ 2811]: SESSION END
(END)



and here the one when it succeeds faxing.

ess c00000007
Apr 09 13:05:34.90: [  855]: SESSION BEGIN 00000007 31742506535
Apr 09 13:05:34.90: [  855]: HylaFAX (tm) Version 4.1.5
Apr 09 13:05:34.90: [  855]: SEND FAX: JOB 5 DEST 2506535 COMMID 00000007
DEVICE '/dev/modem'
Apr 09 13:05:34.90: [  855]: DELAY 75 ms
Apr 09 13:05:35.10: [  855]: DELAY 2600 ms
Apr 09 13:05:37.69: [  855]: DELAY 10 ms
Apr 09 13:05:37.70: [  855]: <-- [4:ATZ\r]
Apr 09 13:05:37.97: [  855]: --> [2:OK]
Apr 09 13:05:37.97: [  855]: DELAY 3000 ms
Apr 09 13:05:40.97: [  855]: <-- [5:ATE0\r]
Apr 09 13:05:41.01: [  855]: --> [4:ATE0]
Apr 09 13:05:41.01: [  855]: --> [2:OK]
Apr 09 13:05:41.01: [  855]: <-- [5:ATV1\r]
Apr 09 13:05:41.05: [  855]: --> [2:OK]
Apr 09 13:05:41.05: [  855]: <-- [5:ATQ0\r]
Apr 09 13:05:41.09: [  855]: --> [2:OK]
Apr 09 13:05:41.09: [  855]: <-- [7:ATS0=0\r]
Apr 09 13:05:41.13: [  855]: --> [2:OK]
Apr 09 13:05:41.13: [  855]: <-- [7:ATS8=2\r]
Apr 09 13:05:41.17: [  855]: --> [2:OK]
Apr 09 13:05:41.17: [  855]: <-- [8:ATS7=60\r]
Apr 09 13:05:41.21: [  855]: --> [2:OK]
Apr 09 13:05:41.21: [  855]: <-- [6:AT&K3\r]
Apr 09 13:05:41.25: [  855]: --> [2:OK]
Apr 09 13:05:41.25: [  855]: <-- [6:AT&D2\r]
Apr 09 13:05:41.29: [  855]: --> [2:OK]
Apr 09 13:05:41.29: [  855]: <-- [6:AT&C1\r]
Apr 09 13:05:41.33: [  855]: --> [2:OK]
Apr 09 13:05:41.33: [  855]: <-- [12:AT+FCLASS=1\r]
Apr 09 13:05:41.36: [  855]: --> [2:OK]
Apr 09 13:05:41.36: [  855]: <-- [5:ATM0\r]
Apr 09 13:05:41.40: [  855]: --> [2:OK]
Apr 09 13:05:41.40: [  855]: <-- [12:AT+FCLASS=1\r]
Apr 09 13:05:41.54: [  855]: --> [2:OK]
Apr 09 13:05:41.55: [  855]: DIAL 2506535
Apr 09 13:05:41.55: [  855]: <-- [12:ATDT2506535\r]
Apr 09 13:06:04.49: [  855]: --> [7:CONNECT]
Apr 09 13:06:05.23: [  855]: --> [2:OK]
Apr 09 13:06:05.23: [  855]: REMOTE NSF "AD 00 36 20 00 00 00 00 6D"
Apr 09 13:06:05.23: [  855]: NSF remote fax equipment: HP
Apr 09 13:06:05.23: [  855]: <-- [9:AT+FRH=3\r]
Apr 09 13:06:05.29: [  855]: --> [7:CONNECT]
Apr 09 13:06:05.95: [  855]: --> [2:OK]
Apr 09 13:06:05.95: [  855]: REMOTE CSI "074 2506535"
Apr 09 13:06:05.95: [  855]: <-- [9:AT+FRH=3\r]
Apr 09 13:06:06.01: [  855]: --> [7:CONNECT]
Apr 09 13:06:06.39: [  855]: --> [2:OK]
Apr 09 13:06:06.39: [  855]: REMOTE best rate 14400 bit/s
Apr 09 13:06:06.39: [  855]: REMOTE max page width 1728 pixels in 215 mm
Apr 09 13:06:06.39: [  855]: REMOTE max unlimited page length
Apr 09 13:06:06.39: [  855]: REMOTE best vres 7.7 line/mm
Apr 09 13:06:06.39: [  855]: REMOTE best format 2-D MMR
Apr 09 13:06:06.39: [  855]: REMOTE supports T.30 Annex A, ECM
Apr 09 13:06:06.39: [  855]: REMOTE best 0 ms/scanline
Apr 09 13:06:06.39: [  855]: USE 14400 bit/s
Apr 09 13:06:06.39: [  855]: USE 0 ms/scanline
Apr 09 13:06:06.39: [  855]: SEND file "docq/doc8.ps;01"
Apr 09 13:06:06.39: [  855]: USE page width 1728 pixels in 215 mm
Apr 09 13:06:06.39: [  855]: USE unlimited page length
Apr 09 13:06:06.39: [  855]: USE 7.7 line/mm
Apr 09 13:06:06.39: [  855]: USE 1-D MR
Apr 09 13:06:06.39: [  855]: SEND training at v.17 14400 bit/s
Apr 09 13:06:06.39: [  855]: <-- [9:AT+FTH=3\r]
Apr 09 13:06:06.76: [  855]: --> [7:CONNECT]
Apr 09 13:06:06.76: [  855]: <-- data [23]
Apr 09 13:06:06.76: [  855]: <-- data [2]
Apr 09 13:06:08.44: [  855]: --> [7:CONNECT]
Apr 09 13:06:08.44: [  855]: <-- data [6]
Apr 09 13:06:08.44: [  855]: <-- data [2]
Apr 09 13:06:08.96: [  855]: --> [2:OK]
Apr 09 13:06:08.96: [  855]: <-- [9:AT+FTS=7\r]
Apr 09 13:06:09.14: [  855]: --> [2:OK]
Apr 09 13:06:09.14: [  855]: <-- [11:AT+FTM=145\r]
Apr 09 13:06:09.19: [  855]: --> [7:CONNECT]
Apr 09 13:06:09.19: [  855]: <-- data [1024]
Apr 09 13:06:09.19: [  855]: <-- data [1024]
Apr 09 13:06:09.19: [  855]: <-- data [652]
Apr 09 13:06:09.19: [  855]: <-- data [2]
Apr 09 13:06:12.50: [  855]: --> [2:OK]
Apr 09 13:06:12.50: [  855]: <-- [9:AT+FRH=3\r]
Apr 09 13:06:12.77: [  855]: --> [7:CONNECT]
Apr 09 13:06:13.81: [  855]: --> [2:OK]
Apr 09 13:06:13.81: [  855]: TRAINING succeeded
Apr 09 13:06:13.81: [  855]: DELAY 75 ms
Apr 09 13:06:13.89: [  855]: <-- [11:AT+FTM=146\r]
Apr 09 13:06:14.24: [  855]: --> [7:CONNECT]
Apr 09 13:06:14.24: [  855]: SEND begin page
Apr 09 13:06:14.24: [  855]: <-- data [1030]
Apr 09 13:06:14.24: [  855]: <-- data [1026]
Apr 09 13:06:14.24: [  855]: <-- data [1029]
Apr 09 13:06:14.25: [  855]: <-- data [1028]
Apr 09 13:06:14.25: [  855]: <-- data [1030]
Apr 09 13:06:15.24: [  855]: <-- data [1026]
Apr 09 13:06:15.24: [  855]: <-- data [1026]
Apr 09 13:06:16.40: [  855]: <-- data [1027]
Apr 09 13:06:16.40: [  855]: <-- data [1030]
Apr 09 13:06:16.40: [  855]: <-- data [1028]
Apr 09 13:06:17.58: [  855]: <-- data [1026]
Apr 09 13:06:17.58: [  855]: <-- data [1029]
Apr 09 13:06:18.74: [  855]: <-- data [1025]
Apr 09 13:06:18.74: [  855]: <-- data [1031]
Apr 09 13:06:19.90: [  855]: <-- data [1029]
Apr 09 13:06:19.90: [  855]: <-- data [1026]
Apr 09 13:06:21.06: [  855]: <-- data [1031]
Apr 09 13:06:21.06: [  855]: <-- data [1031]
Apr 09 13:06:22.22: [  855]: <-- data [1025]
Apr 09 13:06:22.22: [  855]: <-- data [1026]
Apr 09 13:06:23.38: [  855]: <-- data [1029]
Apr 09 13:06:23.38: [  855]: <-- data [1031]
Apr 09 13:06:24.54: [  855]: <-- data [1031]
Apr 09 13:06:24.54: [  855]: <-- data [1026]
Apr 09 13:06:25.70: [  855]: <-- data [1026]
Apr 09 13:06:25.70: [  855]: <-- data [1030]
Apr 09 13:06:26.86: [  855]: <-- data [1027]
Apr 09 13:06:26.86: [  855]: <-- data [1026]
Apr 09 13:06:28.04: [  855]: <-- data [1028]
Apr 09 13:06:28.04: [  855]: <-- data [1032]
Apr 09 13:06:29.20: [  855]: <-- data [1029]
Apr 09 13:06:29.20: [  855]: <-- data [1029]
Apr 09 13:06:30.36: [  855]: <-- data [1026]
Apr 09 13:06:30.36: [  855]: <-- data [1032]
Apr 09 13:06:31.52: [  855]: <-- data [1029]
Apr 09 13:06:31.52: [  855]: <-- data [1028]
Apr 09 13:06:32.68: [  855]: <-- data [1027]
Apr 09 13:06:32.69: [  855]: <-- data [1027]
Apr 09 13:06:33.84: [  855]: <-- data [503]
Apr 09 13:06:33.84: [  855]: SENT 39415 bytes of data
Apr 09 13:06:33.84: [  855]: SEND 1D RTC
Apr 09 13:06:33.84: [  855]: <-- data [29]
Apr 09 13:06:33.84: [  855]: <-- data [2]
Apr 09 13:06:33.84: [  855]: SEND end page
Apr 09 13:06:36.69: [  855]: --> [2:OK]
Apr 09 13:06:36.69: [  855]: <-- [9:AT+FTS=9\r]
Apr 09 13:06:36.89: [  855]: --> [2:OK]
Apr 09 13:06:36.89: [  855]: SEND send EOP (no more pages or documents)
Apr 09 13:06:36.89: [  855]: <-- [9:AT+FTH=3\r]
Apr 09 13:06:36.96: [  855]: --> [7:CONNECT]
Apr 09 13:06:36.96: [  855]: <-- data [3]
Apr 09 13:06:36.96: [  855]: <-- data [2]
Apr 09 13:06:38.29: [  855]: --> [2:OK]
Apr 09 13:06:38.29: [  855]: <-- [9:AT+FRH=3\r]
Apr 09 13:06:38.56: [  855]: --> [7:CONNECT]
Apr 09 13:06:39.62: [  855]: --> [2:OK]
Apr 09 13:06:39.62: [  855]: SEND recv MCF (message confirmation)
Apr 09 13:06:39.62: [  855]: SEND FAX (00000007): FROM
root@localhost.localdomain TO 2506535 (page 1 of 1 sent in 0:33)
Apr 09 13:06:39.62: [  855]: SEND FAX (00000007): FROM
root@localhost.localdomain TO 2506535 (docq/doc8.ps;01 sent in 0:33)
Apr 09 13:06:39.62: [  855]: <-- [9:AT+FTH=3\r]
Apr 09 13:06:39.99: [  855]: --> [7:CONNECT]
Apr 09 13:06:39.99: [  855]: <-- data [3]
Apr 09 13:06:39.99: [  855]: <-- data [2]
Apr 09 13:06:41.37: [  855]: --> [2:OK]
Apr 09 13:06:41.37: [  855]: <-- [5:ATH0\r]
Apr 09 13:06:42.49: [  855]: --> [2:OK]
Apr 09 13:06:42.49: [  855]: SESSION END
(END)


.....


i think  i red last year about some fax machines where you send to are teh
problem..
..

someone who can tel ???


greets peter k




___________________________________________________________________________________________
This message has been scanned for all known viruses by O.A. Systems E-Mail Security daemon.
(koekiemonster) For further information visit: http://www.oa-systems.nl

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*