HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: [hylafax-users] using hylafax with nokia 6210



I guess that hylafax it's not the software that you
need. Maybe gnokii?

--- Kurt Weiss <input.maillists@kwnet.at> wrote:
> hello all
> 
> i've problems using hylafax width nokia 6210 mobile
> phone.
> does somebody work successfully width it?
> 
> the problem:
> after a half page, the fax sends garbage, then the
> transmittion stops,
> the log message is:
> no response to MPS or EOP repeated 3 times
> 
> i had the same problem with an US-Robotics
> Sportster, but there i
> changed successfully to class 1...
> 
> i've tested class 1, class 2 class 2.0
> additionally i've tested modem rate from 38400 -
> 9600
> this only changes the position where hylafax
> terminates (between nothing
> and a half page)
> 
> here's my (last) config.ttyS0: - sending a half page
> - then garbage...
> 
> > CountryCode:        43
> > AreaCode:        699
> > FAXNumber:        +43.699.4272.9926
> > LongDistancePrefix:    0
> > InternationalPrefix:    00
> > DialStringRules:    etc/dialrules
> > ServerTracing:        1
> > SessionTracing:        11
> > RecvFileMode:        0600
> > LogFileMode:        0600
> > DeviceMode:        0600
> > RingsBeforeAnswer:    1
> > SpeakerVolume:        low
> > GettyArgs:        "-h %l dx_%s"
> > LocalIdentifier:    www.kwnet.at
> > TagLineFont:        etc/lutRS18.pcf
> > TagLineFormat:        "From %%l|%c|Page %%P of
> %%T"
> > MaxRecvPages:        25
> > 
> > ModemType:        Class1        # use this to
> supply a hint
> > ModemRate:        14400        # rate for DCE-DTE
> communication
> > 
> > ################i've testet this / without success
> > #ModemFlowControl:    xonxoff        # XON/XOFF
> flow control assumed
> > #
> > ModemSetupDTRCmd:    AT&D2        # setup so DTR
> drop resets modem
> > ModemSetupDCDCmd:    AT&C1        # setup so DCD
> follows carrier
> > #GettyArgs:        "-h %l dx_%s"    # modem must
> auto-detect fax/data
> > 
> > #ModemDialCmd:        ATDT%s        # T for tone
> dialing
> > 
> > ################i've testet this / without success
> > #ModemHardFlowCmd:    AT&K3        # hardware flow
> control cmd
> > 
> > #
> > Class1Cmd:        AT+FCLASS=1    # command to
> enter class 1
> > Class1PPMWaitCmd:    AT+FTS=7    # command to stop
> and wait 
> > Class1TCFWaitCmd:    AT+FTS=7    # command to stop
> and wait 
> > Class1EOPWaitCmd:    AT+FTS=9    # command to stop
> and wait 
> > Class1MsgRecvHackCmd:    ""    # command to avoid
> +FCERROR before image
> > Class1TCFResponseDelay:    75        # 75ms delay
> between recv TCF & 
> > Class1SendMsgDelay:    75        # 75ms delay
> after training
> > Class1SwitchingCmd:    AT+FRS=7    # silence
> between HDLC recv and 
> > Class1TrainingRecovery:    1500        # 1.5sec
> delay after training 
> > Class1RecvAbortOK:    200
> > Class1FrameOverhead:    4        # 4 byte overhead
> in recvd HDLC 
> > Class1RecvIdentTimer:    40000        # 35+5secs
> waiting for ident 
> > Class1TCFMaxNonZero:    10        # max 10% of
> data may be 
> > Class1TCFMinRun: 1000        # min run is 2/3rds
> of TCF
> 
> thx in adv
> kurt
> 
> 
> 
> 
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
>   To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe
> hylafax-users-request@hylafax.org < /dev/null
>   *To learn about commercial HylaFAX(tm) support,
> mail sales@hylafax.org.*
> 


__________________________________________________
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now.
http://mailplus.yahoo.com

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*




Project hosted by iFAX Solutions