HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] can't send or receive fax using Hylafax



I am using Redhat 8.0 and Conexant linmodem. I have installed latest
linmodem drivers and using latest HylaFax software. I am not able to
send fax. tried many times and no success. Seems like something wrong
with AT+FTM=145 command. Any help is appreciated.

Log of sending a fax:
Jan 02 14:13:32.13: [13009]: SESSION BEGIN 00000011 1**********
Jan 02 14:13:32.14: [13009]: HylaFAX (tm) Version 4.1.5
Jan 02 14:13:32.14: [13009]: SEND FAX: JOB 9 DEST 1-********** COMMID
00000011 DEVICE '/dev/modem'
Jan 02 14:13:32.14: [13009]: DELAY 75 ms
Jan 02 14:13:32.22: [13009]: DELAY 2600 ms
Jan 02 14:13:34.82: [13009]: DELAY 10 ms
Jan 02 14:13:34.84: [13009]: <-- [4:ATZ\r]
Jan 02 14:13:34.89: [13009]: --> [2:OK]
Jan 02 14:13:34.89: [13009]: DELAY 3000 ms
Jan 02 14:13:37.89: [13009]: <-- [5:ATX3\r]
Jan 02 14:13:37.91: [13009]: --> [4:ATX3]
Jan 02 14:13:37.91: [13009]: --> [2:OK]
Jan 02 14:13:37.91: [13009]: <-- [5:ATE0\r]
Jan 02 14:13:37.93: [13009]: --> [4:ATE0]
Jan 02 14:13:37.93: [13009]: --> [2:OK]
Jan 02 14:13:37.93: [13009]: <-- [5:ATV1\r]
Jan 02 14:13:37.94: [13009]: --> [2:OK]
Jan 02 14:13:37.94: [13009]: <-- [5:ATQ0\r]
Jan 02 14:13:37.96: [13009]: --> [2:OK]
Jan 02 14:13:37.96: [13009]: <-- [7:ATS0=0\r]
Jan 02 14:13:37.98: [13009]: --> [2:OK]
Jan 02 14:13:37.98: [13009]: <-- [7:ATS8=2\r]
Jan 02 14:13:38.00: [13009]: --> [2:OK]
Jan 02 14:13:38.00: [13009]: <-- [8:ATS7=60\r]
Jan 02 14:13:38.01: [13009]: --> [2:OK]
Jan 02 14:13:38.01: [13009]: <-- [6:AT&K3\r]
Jan 02 14:13:38.03: [13009]: --> [2:OK]
Jan 02 14:13:38.03: [13009]: <-- [6:AT&D2\r]
Jan 02 14:13:38.05: [13009]: --> [2:OK]
Jan 02 14:13:38.05: [13009]: <-- [6:AT&C1\r]
Jan 02 14:13:38.07: [13009]: --> [2:OK]
Jan 02 14:13:38.07: [13009]: <-- [12:AT+FCLASS=1\r]
Jan 02 14:13:38.08: [13009]: --> [2:OK]
Jan 02 14:13:38.08: [13009]: <-- [7:ATL1M1\r]
Jan 02 14:13:38.10: [13009]: --> [2:OK]
Jan 02 14:13:38.10: [13009]: <-- [12:AT+FCLASS=1\r]
Jan 02 14:13:38.21: [13009]: --> [2:OK]
Jan 02 14:13:38.21: [13009]: DIAL 16176937180
Jan 02 14:13:38.21: [13009]: <-- [16:ATDT**********\r]
Jan 02 14:13:54.56: [13009]: --> [7:CONNECT]
Jan 02 14:13:55.24: [13009]: --> [2:OK]
Jan 02 14:13:55.24: [13009]: REMOTE NSF "AD 00 00 79 20 A1 C8 0A 29"
Jan 02 14:13:55.24: [13009]: NSF remote fax equipment: Pitney Bowes 
Jan 02 14:13:55.24: [13009]: <-- [9:AT+FRH=3\r]
Jan 02 14:13:55.37: [13009]: --> [7:CONNECT]
Jan 02 14:13:56.19: [13009]: --> [2:OK]
Jan 02 14:13:56.19: [13009]: REMOTE NSF "00 00 09 00 60 00 98 48 B8 F0
A8 F0 48 A4 C4 98 78 A8 C4 C4 F0 F0 F0 F0 F0 F0 F0 00 00 3A"
Jan 02 14:13:56.19: [13009]: NSF remote fax equipment: Xerox/Toshiba 
Jan 02 14:13:56.19: [13009]: <-- [9:AT+FRH=3\r]
Jan 02 14:13:56.31: [13009]: --> [7:CONNECT]
Jan 02 14:13:56.88: [13009]: --> [2:OK]
Jan 02 14:13:56.88: [13009]: REMOTE CSI "**********"
Jan 02 14:13:56.88: [13009]: <-- [9:AT+FRH=3\r]
Jan 02 14:13:57.01: [13009]: --> [7:CONNECT]
Jan 02 14:13:57.21: [13009]: --> [2:OK]
Jan 02 14:13:57.21: [13009]: REMOTE best rate 33600 bit/s
Jan 02 14:13:57.21: [13009]: REMOTE max page width 1728 pixels in 215 mm
Jan 02 14:13:57.21: [13009]: REMOTE max unlimited page length 
Jan 02 14:13:57.21: [13009]: REMOTE best vres 7.7 line/mm
Jan 02 14:13:57.21: [13009]: REMOTE best format 2-D MMR
Jan 02 14:13:57.21: [13009]: REMOTE supports T.30 Annex A, ECM
Jan 02 14:13:57.21: [13009]: REMOTE best 0 ms/scanline
Jan 02 14:13:57.21: [13009]: USE 14400 bit/s
Jan 02 14:13:57.21: [13009]: USE 0 ms/scanline
Jan 02 14:13:57.21: [13009]: SEND file "docq/doc9.ps;01"
Jan 02 14:13:57.21: [13009]: USE page width 1728 pixels in 215 mm
Jan 02 14:13:57.21: [13009]: USE unlimited page length 
Jan 02 14:13:57.21: [13009]: USE 7.7 line/mm
Jan 02 14:13:57.21: [13009]: USE 1-D MR
Jan 02 14:13:57.21: [13009]: SEND training at v.17 14400 bit/s
Jan 02 14:13:57.21: [13009]: <-- [9:AT+FTH=3\r]
Jan 02 14:13:57.66: [13009]: --> [7:CONNECT]
Jan 02 14:13:57.66: [13009]: <-- data [23]
Jan 02 14:13:57.66: [13009]: <-- data [2]
Jan 02 14:13:59.37: [13009]: --> [7:CONNECT]
Jan 02 14:13:59.37: [13009]: <-- data [6]
Jan 02 14:13:59.37: [13009]: <-- data [2]
Jan 02 14:13:59.99: [13009]: --> [2:OK]
Jan 02 14:13:59.99: [13009]: <-- [9:AT+FTS=7\r]
Jan 02 14:14:00.28: [13009]: --> [2:OK]
Jan 02 14:14:00.28: [13009]: <-- [11:AT+FTM=145\r]
Jan 02 14:14:00.37: [13009]: --> [7:CONNECT]
Jan 02 14:14:00.37: [13009]: <-- data [1024]
Jan 02 14:14:00.37: [13009]: <-- data [1024]
Jan 02 14:14:00.37: [13009]: <-- data [652]
Jan 02 14:14:00.37: [13009]: <-- data [2]
Jan 02 14:14:30.37: [13009]: MODEM <Timeout>
Jan 02 14:14:30.37: [13009]: Problem sending TCF data
Jan 02 14:14:30.37: [13009]: <-- [9:AT+FRH=3\r]
Jan 02 14:14:33.47: [13009]: --> [0:]
Jan 02 14:14:33.47: [13009]: MODEM <Empty line>
Jan 02 14:14:33.47: [13009]: <-- data [1]
Jan 02 14:14:33.67: [13009]: MODEM <Timeout>
Jan 02 14:14:33.67: [13009]: DELAY 1500 ms
Jan 02 14:14:35.18: [13009]: SEND training at v.17 12000 bit/s
Jan 02 14:14:35.18: [13009]: <-- [9:AT+FTH=3\r]
Jan 02 14:14:37.73: [13009]: Error sending T.30 prologue frames
Jan 02 14:14:37.73: [13009]: SEND training at v.17 9600 bit/s
Jan 02 14:14:37.73: [13009]: <-- [9:AT+FTH=3\r]
Jan 02 14:14:40.28: [13009]: Error sending T.30 prologue frames
Jan 02 14:14:40.28: [13009]: SEND training at v.17 7200 bit/s
Jan 02 14:14:40.28: [13009]: <-- [9:AT+FTH=3\r]
Jan 02 14:14:42.83: [13009]: Error sending T.30 prologue frames
Jan 02 14:14:42.83: [13009]: SEND training at v.27ter 4800 bit/s
Jan 02 14:14:42.83: [13009]: <-- [9:AT+FTH=3\r]
Jan 02 14:14:45.38: [13009]: Error sending T.30 prologue frames
Jan 02 14:14:45.38: [13009]: SEND training at v.27ter fallback mode 2400
bit/s
Jan 02 14:14:45.38: [13009]: <-- [9:AT+FTH=3\r]
Jan 02 14:14:47.93: [13009]: Error sending T.30 prologue frames
Jan 02 14:14:47.93: [13009]: TRAINING failed
Jan 02 14:14:47.93: [13009]: <-- [9:AT+FTH=3\r]
Jan 02 14:14:50.48: [13009]: --> [0:]
Jan 02 14:14:50.48: [13009]: <-- [5:ATH0\r]
Jan 02 14:14:55.48: [13009]: MODEM <Timeout>
Jan 02 14:14:55.65: [13009]: SESSION END



**********
Modem related stuff from config.modem file:

#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use this to supply a hint
ModemRate:		19200		# rate for DCE-DTE communication
ModemFlowControl:	rtscts		# default
#
ModemNoFlowCmd:		AT&K0		# setup no flow control
ModemHardFlowCmd:	AT&K3		# setup hardware flow control
ModemSoftFlowCmd:	AT&K4		# setup software flow control
ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#
ModemMfrQueryCmd:	!Rockwell
ModemModelQueryCmd:	!RC288DPi
ModemRevQueryCmd:	ATI3		# product information
#
ModemDialCmd:		ATDT%s		# T for tone dialing
#
Class1Cmd:              AT+FCLASS=1     # command to enter class 1
Class1TCFResponseDelay: 75              # 75ms delay between recv TCF &
response
Class1SendMsgDelay:     75              # 75ms delay after training
Class1TrainingRecovery: 1500            # 1.5sec delay after training
failure
Class1RecvAbortOK:      200             # wait 200ms for abort response


**********

Output from probemodem:
-----------------------
Probing for best speed to talk to modem: 38400 OK.
 
This looks like a Class 1 and 1.0 modem.
 
ATI0    RESULT = "OK"   RESPONSE = "56000"
ATI1    RESULT = "OK"   RESPONSE = "255"
ATI2    RESULT = "OK"   RESPONSE = "OK"
ATI3    RESULT = "OK"   RESPONSE = "hcfpcimodem-0.99mbsibeta02123100"
ATI4    RESULT = "OK"   RESPONSE = "Conexant Octopus HCF V.90 PCI Modem"
ATI5    RESULT = "OK"   RESPONSE = "B5"
ATI6    RESULT = "OK"   RESPONSE = "DP Part 74"
ATI7    RESULT = "ERROR"        RESPONSE = "ERROR"
ATI8    RESULT = "OK"   RESPONSE = "Dec 31 2002 ; 14:43:10"
ATI9    RESULT = "OK"   RESPONSE = "USA"
 
Class 1 stuff...
 
AT+FCLASS=?     RESULT = "OK"   RESPONSE = "0,1,1.0"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "0"
AT+FCLASS=0     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=1     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "0"
AT+FJUNK=?      RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FJUNK?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FAA=?        RESULT = "OK"   RESPONSE = "0,1"
AT+FAA? RESULT = "OK"   RESPONSE = "0"
AT+FAE=?        RESULT = "OK"   RESPONSE = "0,1"
AT+FAE? RESULT = "OK"   RESPONSE = "0"
AT+FTH=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FRH=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FTM=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FRM=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FTS=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FRS=?        RESULT = "ERROR"        RESPONSE = "ERROR"
 
Class 1.0 stuff...
 
AT+FCLASS=?     RESULT = "OK"   RESPONSE = "0,1,1.0"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "0"
AT+FCLASS=0     RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS=1.0   RESULT = "OK"   RESPONSE = "OK"
AT+FCLASS?      RESULT = "OK"   RESPONSE = "0"
AT+FJUNK=?      RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FJUNK?       RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FAA=?        RESULT = "OK"   RESPONSE = "0,1"
AT+FAA? RESULT = "OK"   RESPONSE = "0"
AT+FAE=?        RESULT = "OK"   RESPONSE = "0,1"
AT+FAE? RESULT = "OK"   RESPONSE = "0"
AT+FTH=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FRH=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FTM=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FRM=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FTS=?        RESULT = "ERROR"        RESPONSE = "ERROR"
AT+FRS=?        RESULT = "ERROR"        RESPONSE = "ERROR"


Thanks

This is a digitally signed message part




Project hosted by iFAX Solutions