[hylafax-users] problem to receive data to set class 2.0 modem on hylafax

["Danielh" <danielh@figment.net>]

Hello!

Anyone know how to configure class 2.0 modem on hylafax to receive fax and
data? I can receive fax, but I can use modem to connect the fax server.
Thanks!

Daniel


My configuration file is following:

# Generic Class 2.0 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		1
AreaCode:		416
FAXNumber:		+1.999.555.1212
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0660
LogFileMode:		0660
DeviceMode:		0660
RingsBeforeAnswer:	1
SpeakerVolume:		quiet
GettyArgs:		"-h %l F%s"
LocalIdentifier:	"NothingSetup"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2.0	# use this to supply a hint
#ModemRate:		19200		# max rate for DCE-DTE communication
#ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed
#ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
#ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:		""		# stuff to do when modem is reset
#ModemAnswerCmd:		ATA		# use this to answer phone
#ModemNoFlowCmd:		AT&K		# disable flow control cmd
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
#ModemSoftFlowCmd:	AT&K4		# software flow control cmd
#ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:	ATE0		# disable command echo
#ModemVerboseResultsCmd:	ATV1		# enable verbose command results
#ModemResultCodesCmd:	ATQ0		# enable result codes
#ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
#ModemSoftResetCmd:	ATZ		# do soft reset of modem
#ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds
#ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
#ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:			AT+FCLASS=2.0	# command to enter class 2.0
Class2BORCmd:		AT+FBO=0	# bit order for phase B/C/D (direct)
Class2CQCmd:		""		# commands to enable copy quality proc.
Class2AbortCmd:		AT+FKS		# abort session command
Class2CQQueryCmd:		AT+FCQ=?	# query for copy quality capabilities
Class2DCCQueryCmd:	AT+FCC=?	# query for modem capabilities
Class2TBCCmd:		AT+FPP=0	# setup stream mode
Class2CRCmd:		AT+FCR=1	# enable capability to receive
Class2PHCTOCmd:		AT+FCT=30	# set phase C timeout parameter
Class2BUGCmd:		AT+FBU=1	# enable HDLC frame tracing
Class2LIDCmd:		AT+FLI		# set local identifier command
Class2DCCCmd:		AT+FCC		# set modem capabilities command
Class2DISCmd:		AT+FIS		# set session parameters command
Class2DDISCmd:		""		# disable pre-dial DIS command hack
Class2CIGCmd:		AT+FPI		# set polling identifier command
Class2NRCmd:		AT+FNR=1,1,1,1	# setup status reporting command
Class2PIECmd:		AT+FIE=1	# disable interrupt-enable command
Class2PTSCmd:		AT+FPS		# set post-page status command
Class2SPLCmd:		AT+FSP		# set polling indicator command
Class2NFLOCmd:		AT+FLO=0	# set no flow control command
Class2SFLOCmd:		AT+FLO=1	# set software flow control command
Class2HFLOCmd:		AT+FLO=2	# set hardware flow control command


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*