[hylafax-users] Another Communication failure during Phase B/C

["Jessie Hui" <jeshui@siliconcreation.com>]

Hi,

 

I have another problems about the communication failure during Phase B/C, I am new to Hylafax, and so I cannot solve it out, if you have any idea on that, please help me~ thx~~~~~

 

My system is

HylaFAX v4.1 under Linux version 2.4.4-64GB-SMP <SUSE> ; Robotics Sportster Voice 33.6 Fax modem

 

Here attach the session log.

 

Oct 11 16:57:51.98: [16325]: SESSION BEGIN 00000350 85241527804800
Oct 11 16:57:51.98: [16325]: SEND FAX: JOB 176 DEST 27804800 COMMID 00000350
Oct 11 16:57:51.98: [16325]: MODEM set DTR OFF
Oct 11 16:57:51.98: [16325]: DELAY 2600 ms
Oct 11 16:57:54.58: [16325]: MODEM set DTR ON
Oct 11 16:57:54.58: [16325]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS
Oct 11 16:57:54.58: [16325]: MODEM flush i/o
Oct 11 16:57:54.58: [16325]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Oct 11 16:57:54.72: [16325]: --> [2:OK]
Oct 11 16:57:54.72: [16325]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
Oct 11 16:57:54.86: [16325]: --> [2:OK]
Oct 11 16:57:54.86: [16325]: <-- [14:AT+FCLASS=2.0\r]
Oct 11 16:57:55.00: [16325]: --> [2:OK]
Oct 11 16:57:55.00: [16325]: <-- [9:AT+FLO=2\r]
Oct 11 16:57:55.14: [16325]: --> [2:OK]
Oct 11 16:57:55.14: [16325]: <-- [9:AT+FPP=0\r]
Oct 11 16:57:55.28: [16325]: --> [2:OK]
Oct 11 16:57:55.28: [16325]: <-- [9:AT+FBO=0\r]
Oct 11 16:57:55.42: [16325]: --> [2:OK]
Oct 11 16:57:55.42: [16325]: <-- [10:AT+FCT=30\r]
Oct 11 16:57:55.56: [16325]: --> [2:OK]
Oct 11 16:57:55.56: [16325]: <-- [15:AT+FNR=1,1,1,0\r]
Oct 11 16:57:55.70: [16325]: --> [2:OK]
Oct 11 16:57:55.70: [16325]: <-- [9:AT+FIE=0\r]
Oct 11 16:57:55.84: [16325]: --> [2:OK]
Oct 11 16:57:55.84: [16325]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Oct 11 16:57:55.98: [16325]: --> [2:OK]
Oct 11 16:57:55.98: [16325]: <-- [5:ATM0\r]
Oct 11 16:57:56.11: [16325]: --> [2:OK]
Oct 11 16:57:56.11: [16325]: MODEM input buffering enabled
Oct 11 16:57:56.11: [16325]: <-- [14:AT+FCLASS=2.0\r]
Oct 11 16:57:56.35: [16325]: --> [2:OK]
Oct 11 16:57:56.35: [16325]: <-- [9:AT+FLO=2\r]
Oct 11 16:57:56.59: [16325]: --> [2:OK]
Oct 11 16:57:56.59: [16325]: <-- [9:AT+FPP=0\r]
Oct 11 16:57:56.83: [16325]: --> [2:OK]
Oct 11 16:57:56.83: [16325]: <-- [9:AT+FBO=0\r]
Oct 11 16:57:57.07: [16325]: --> [2:OK]
Oct 11 16:57:57.07: [16325]: <-- [10:AT+FCT=30\r]
Oct 11 16:57:57.31: [16325]: --> [2:OK]
Oct 11 16:57:57.31: [16325]: <-- [15:AT+FNR=1,1,1,0\r]
Oct 11 16:57:57.55: [16325]: --> [2:OK]
Oct 11 16:57:57.55: [16325]: <-- [9:AT+FIE=0\r]
Oct 11 16:57:57.79: [16325]: --> [2:OK]
Oct 11 16:57:57.79: [16325]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Oct 11 16:57:58.03: [16325]: --> [2:OK]
Oct 11 16:57:58.03: [16325]: <-- [22:AT+FLI="www.mango.cc"\r]
Oct 11 16:57:58.27: [16325]: --> [2:OK]
Oct 11 16:57:58.27: [16325]: DIAL 27804800
Oct 11 16:57:58.27: [16325]: <-- [13:ATDT27804800\r]
Oct 11 16:58:22.26: [16325]: --> [4:+FCO]
Oct 11 16:58:25.09: [16325]: --> [27:+FCI:"                    "]
Oct 11 16:58:25.09: [16325]: REMOTE CSI ""
Oct 11 16:58:25.09: [16325]: --> [20:+FIS:1,3,0,2,1,0,0,4]
Oct 11 16:58:25.09: [16325]: --> [2:OK]
Oct 11 16:58:25.09: [16325]: REMOTE best rate 9600 bit/s
Oct 11 16:58:25.09: [16325]: REMOTE max page width 1728 pixels in 215 mm
Oct 11 16:58:25.09: [16325]: REMOTE max unlimited page length
Oct 11 16:58:25.09: [16325]: REMOTE best vres 7.7 line/mm
Oct 11 16:58:25.09: [16325]: REMOTE best format 2-D MR
Oct 11 16:58:25.09: [16325]: REMOTE best 20 ms, 10 ms/scanline
Oct 11 16:58:25.09: [16325]: USE 9600 bit/s
Oct 11 16:58:25.09: [16325]: USE 20 ms, 10 ms/scanline
Oct 11 16:58:25.09: [16325]: SEND file "docq/doc176.ps;30"
Oct 11 16:58:25.09: [16325]: USE page width 1728 pixels in 215 mm
Oct 11 16:58:25.09: [16325]: USE unlimited page length
Oct 11 16:58:25.09: [16325]: USE 3.85 line/mm
Oct 11 16:58:25.09: [16325]: USE 1-D MR
Oct 11 16:58:25.09: [16325]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r]
Oct 11 16:58:25.33: [16325]: --> [2:OK]
Oct 11 16:58:25.33: [16325]: <-- [7:AT+FDT\r]
Oct 11 16:58:25.60: [16325]: --> [20:+FCS:0,3,0,2,0,0,0,4]
Oct 11 16:58:32.03: [16325]: --> [7:CONNECT]
Oct 11 16:58:32.03: [16325]: SEND begin page
Oct 11 16:58:32.03: [16325]: <-- data [1034]
Oct 11 16:58:32.03: [16325]: <-- data [1026]
Oct 11 16:58:32.03: [16325]: <-- data [1025]
Oct 11 16:58:32.03: [16325]: <-- data [1027]
Oct 11 16:58:33.02: [16325]: <-- data [1028]
Oct 11 16:58:33.02: [16325]: <-- data [425]
Oct 11 16:58:33.02: [16325]: SENT 5544 bytes of data
Oct 11 16:58:33.02: [16325]: SEND 1D RTC
Oct 11 16:58:33.02: [16325]: <-- data [9]
Oct 11 16:58:33.02: [16325]: SEND end page
Oct 11 16:58:33.02: [16325]: SEND send EOP (no more pages or documents)
Oct 11 16:58:33.02: [16325]: <-- data [2]
Oct 11 16:58:44.03: [16325]: --> [5:ERROR]
Oct 11 16:58:44.03: [16325]: SEND recv RTN (retrain negative)
Oct 11 16:58:44.03: [16325]: <-- [23:AT+FIS=0,2,0,2,0,0,0,4\r]
Oct 11 16:58:44.27: [16325]: --> [2:OK]
Oct 11 16:58:44.27: [16325]: <-- [7:AT+FDT\r]
Oct 11 17:01:44.27: [16325]: MODEM TIMEOUT: reading line from modem
Oct 11 17:01:44.27: [16325]: MODEM <Timeout>
Oct 11 17:01:44.27: [16325]: <-- [7:AT+FKS\r]
Oct 11 17:02:14.27: [16325]: MODEM TIMEOUT: reading line from modem
Oct 11 17:02:14.27: [16325]: MODEM <Timeout>
Oct 11 17:02:14.27: [16325]: SEND FAILED: Communication failure during Phase B/C; too many attempts to send
Oct 11 17:02:14.27: [16325]: <-- [5:ATH0\r]
Oct 11 17:02:19.27: [16325]: MODEM TIMEOUT: reading line from modem
Oct 11 17:02:19.27: [16325]: MODEM <Timeout>
Oct 11 17:02:19.27: [16325]: MODEM set DTR OFF
Oct 11 17:02:19.27: [16325]: SESSION END

 

Best regards,

Jessie