[hylafax-users] Zyxel 2864i + DID

["Giorgio Biondi" <gbiondi@tech2.it>]

Hi,


I have a little problem on fax inbound routing. My telco has enable this
information on my isdn line.
The inboud and outbound fax work fine.
I want to route inbound fax from called number...and here start my problem.

I have tested my $CIDNUMBER, my $5 variable, but nothing, this 'var' is
always empty.
I have read a post message, but your faxgetty send to faxrecv a corret
parameter.
My faxgetty send to faxrecv empty parameter, you can see this on last line
on follow log...
Can be a wrong modem configuration? I have set some value on config.ttyS1 in
bad manner?

Somebody have modem and configuration like this for help to solve this
quest?




***MESSAGES LOG***
Oct 14 13:23:15 fax FaxGetty[20122]: MODEM ZYXEL E2864/V 3.00a
Oct 14 13:24:01 fax FaxGetty[20122]: ANSWER: FAX CONNECTION  DEVICE
'/dev/ttyS1'
Oct 14 13:24:20 fax FaxGetty[20122]: RECV FAX (00000170): from 390102708238,
page 1 in 0:15, INF, 3.85 line/mm, 2-D MR, 14400 bit/s
Oct 14 13:24:20 fax FaxGetty[20122]: RECV FAX (00000170): recvq/fax00051.tif
from 390102708238, route to <unspecified>, 1 pages in 0:19
Oct 14 13:24:23 fax FaxGetty[20122]: RECV FAX: bin/faxrcvd
"recvq/fax00051.tif" "ttyS1" "00000170" "" "" ""

----------------------------------------------------------------------------
------------------------^^^^^^^
EMPTY
PARAMETER







***HYLAFAX LOG***
[root@fax root]# cat /var/spool/hylafax/log/c00000170
Oct 14 13:23:42.63: [20122]: SESSION BEGIN 00000170 39010366
Oct 14 13:23:42.63: [20122]: HylaFAX (tm) Version 4.1.3
Oct 14 13:23:42.63: [20122]: <-- [4:ATA\r]
Oct 14 13:23:42.63: [20122]: --> [13:FM:238 TO:366]
Oct 14 13:23:42.84: [20122]: --> [16:SERVIZI GENERALI]
Oct 14 13:24:01.86: [20122]: --> [4:+FCO]
Oct 14 13:24:01.86: [20122]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS1'
Oct 14 13:24:01.86: [20122]: RECV FAX: begin
[bla bla bla...]









***config.ttyS1***
#
#
CountryCode:            39
AreaCode:               010
FAXNumber:              366
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      "1 "
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "-----------------"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
QualifyCID:             etc/cid
NoCarrierRetrys:        3
MaxRecvPages:           99
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              19200
ModemFlowControl:       rtscts          # default
#
ModemNoFlowCmd:         AT&H0           # disable flow control
ModemHardFlowCmd:       AT&H3           # hardware flow control
ModemSoftFlowCmd:       AT&H4           # software flow control
ModemSetupDTRCmd:       AT&D2           # DTR off causes modem to hang up
ModemSetupDCDCmd:       AT&C1           # DCD tracks carrier
#
ModemSetupAACmd:        AT+FAA=1        # enable in current class
#
# Additional reset commands:
#
# &B1     DTE-DCE rate is fixed at DTE setting
# &N0     Auto-negotiate highest possible DCE-DCE link rate
# &S0     DSR always on
# *F0     Deny remote configuration
#         (actually *F0 doesn't work in the firmware -- sigh)
# S18=4   Receive at 38400 (removed from default)
# S38.3=1 DCD on/off sequence follows UNIX standard; also
#         fix receiving baud rate at S18 value
#
ModemResetCmds:         AT&B1&N0&S0S38.3=1&l1
#
ModemDialCmd:           ATDT%s          # no '@' 'cuz then busy not
recognized
NoCarrierRetrys:        3               # retry 3 times on no carrier
#
ModemSetVolumeCmd:      "ATM0 ATM1L1 ATM1L3 ATM1L5 ATM1L7"
#
# Caller ID configuration setup.
#
QualifyCID:             etc/cid         # CID access control list file
CIDNumber:              "FM:" # pattern string for phone number info
#CIDName:                "FM:"  # pattern string for identity info
#
PagerSetupCmds:         AT&K0&N15       # use V.22 at 1200 bps (PageNet)









____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*