Re: [hylafax-users] missing part of the line using U.S.Robotic modem

["Judy Yam" <judy_yam@hotmail.com>]

Hi all Hylafax-users,

A special thanks to Sedat Yilmazer and also to Rob Sherman for helping me 
with their suggestions.  I'd tried many changes in the flow control but in 
my case, it didn't seem to work.  So I want to know if anyone had a WORKING 
configuration for U.S. Robotics 56K Faxmodem V.92?

Thanks to all of you.
Judy.


>From: "Sedat Yilmazer" <sedat@kibele.com>
>To: "'Judy Yam'" <judy_yam@hotmail.com>
>Subject: RE: [hylafax-users] missing part of the line using U.S.Robotic 
>modem
>Date: Thu, 5 Sep 2002 09:46:38 +0300
>
>
>  Check out the flow control. Also check the ModemHardFlowCmd
>ModemSoftFlowCmd parameters. I had a similar problem once and as I can
>remember these two AT commands were different in the modem manual
>
>  Sedat Yilmazer
>
>-----Original Message-----
>From: hylafax-users-bounce@hylafax.org
>[mailto:hylafax-users-bounce@hylafax.org] On Behalf Of Judy Yam
>Sent: Wednesday, September 04, 2002 11:44 PM
>To: hylafax-users@hylafax.org
>Subject: [hylafax-users] missing part of the line using U.S.Robotic
>modem
>
>Hi all Hylafax-Users,
>
>I have a problem that really embarrassing me.  I am using
>hylafax-4.1.2-1rh7
>with Linux 7.2 and a modem U.S.Robotic 56k FAX EXT v5.4.30.  Each time
>that
>I send a fax, the output came out with some strange lines, I mean it
>print
>part of the line(mising top or middle or bottom of a line [not of a
>page]).
>Did anybody has experienced that kind of problem?  Here's my modem
>configuration:
>
>CountryCode:            1
>AreaCode:               514
>FAXNumber:              +1.514.333.3333
>LongDistancePrefix:     1
>InternationalPrefix:    011
>DialStringRules:        etc/dialrules
>ServerTracing:          1
>SessionTracing:         11
>RecvFileMode:           0600
>LogFileMode:            0600
>DeviceMode:             0600
>RingsBeforeAnswer:      0
>SpeakerVolume:          off
>GettyArgs:              "-h %l dx_%s"
>LocalIdentifier:        "NothingSetup"
>TagLineFont:            etc/lutRS18.pcf
>TagLineFormat:          ""
>MaxRecvPages:           25
>#
>#
># Modem-related stuff: should reflect modem command interface
># and hardware connection/cabling (e.g. flow control).
>#
>ModemType:              Class1          # use class 1 interface
>ModemRate:              19200           # rate for DCE-DTE communication
>ModemFlowControl:       xonxoff         # hardware flow control
>#
>ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
>ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
>(or
>not)
>ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow
>control
>ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
>control
>ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
>control
>ModemResultCodesCmd:    ATQ0X4          # enable result codes
>#
>ModemMfrQueryCmd:       !USR
>ModemModelQueryCmd:     ATI3
>ModemRevQueryCmd:       ATI7            # XXX returns a multi-line
>result
>#
># When AT+FCLASS=1 is issued the modem automatically switches
># to software flow control; these parameters let the fax software
># reset flow control as needed after entering Class 1.
>#
>Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow
>control
>Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow
>control
>Class1SFLOCmd:          ""              # modem does this automatically
>#
># The remainder of this configuration is included so that the
># modem "idles" in Class 0 while not sending or receiving facsimile.
>#
>ModemSetupAACmd:        AT+FCLASS=0     # leave modem idling in class 0
>ModemAnswerCmd:         AT+FCLASS=1A    # answer in Class 1
>#
># Disables the reporting of bad frames by the modem.  This
># overcomes a firmware problem in the x2 and V90 Sportsters.
># It is not necessary for the Courier modem.
>#
>Class2NRCmd:    AT+FNR=1,1,1,0
>
>Thanks in advance dear friends.
>Judy.
>
>
>
>
>_________________________________________________________________
>MSN Photos is the easiest way to share and print your photos:
>http://photos.msn.com/support/worldwide.aspx
>
>
>____________________ HylaFAX(tm) Users Mailing List
>_______________________
>   To subscribe/unsubscribe, click
>http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org <
>/dev/null
>   *To learn about commercial HylaFAX(tm) support, mail
>sales@hylafax.org.*






_________________________________________________________________
Join the world’s largest e-mail service with MSN Hotmail. 
http://www.hotmail.com


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*