Re: [hylafax-users] strange behavior...

[KY Lui <kylui@pcgsys.com>]

Title: RE: [hylafax-users] strange behavior...

Dear all,

i tried to send a fax to a fax machine. the system log told me that the fax had been sent successfully.
however, i cant get the fax in the destination side. please attached the log below

please help... thanks
========= log ==========
Aug 14 09:23:58.81: [ 2673]: SESSION BEGIN 00000044 28812370
Aug 14 09:23:58.81: [ 2673]: HylaFAX (tm) Version 4.1.3
Aug 14 09:23:58.81: [ 2673]: SEND FAX: JOB 14 DEST 28812370 COMMID 00000044 DEVICE '/dev/ttyS0'
Aug 14 09:23:58.81: [ 2673]: MODEM set DTR OFF
Aug 14 09:23:58.81: [ 2673]: DELAY 75 ms
Aug 14 09:23:58.88: [ 2673]: MODEM set DTR ON
Aug 14 09:23:58.88: [ 2673]: DELAY 2600 ms
Aug 14 09:24:01.48: [ 2673]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
Aug 14 09:24:01.48: [ 2673]: MODEM flush i/o
Aug 14 09:24:01.48: [ 2673]: <-- [4:ATZ\r]
Aug 14 09:24:01.62: [ 2673]: --> [2:OK]
Aug 14 09:24:01.62: [ 2673]: DELAY 3000 ms
Aug 14 09:24:04.62: [ 2673]: <-- [5:ATE0\r]
Aug 14 09:24:04.76: [ 2673]: --> [4:ATE0]
Aug 14 09:24:04.76: [ 2673]: --> [2:OK]
Aug 14 09:24:04.76: [ 2673]: <-- [5:ATV1\r]
Aug 14 09:24:04.90: [ 2673]: --> [2:OK]
Aug 14 09:24:04.90: [ 2673]: <-- [7:ATQ0X4\r]
Aug 14 09:24:05.04: [ 2673]: --> [2:OK]
Aug 14 09:24:05.04: [ 2673]: <-- [7:ATS0=0\r]
Aug 14 09:24:05.18: [ 2673]: --> [2:OK]
Aug 14 09:24:05.18: [ 2673]: <-- [7:ATS8=2\r]
Aug 14 09:24:05.32: [ 2673]: --> [2:OK]
Aug 14 09:24:05.32: [ 2673]: <-- [8:ATS7=60\r]
Aug 14 09:24:05.46: [ 2673]: --> [2:OK]
Aug 14 09:24:05.46: [ 2673]: <-- [12:AT&H2&I2&R1\r]
Aug 14 09:24:05.60: [ 2673]: --> [2:OK]
Aug 14 09:24:05.60: [ 2673]: <-- [11:ATS13=1&D2\r]
Aug 14 09:24:05.74: [ 2673]: --> [2:OK]
Aug 14 09:24:05.74: [ 2673]: <-- [6:AT&C1\r]
Aug 14 09:24:05.88: [ 2673]: --> [2:OK]
Aug 14 09:24:05.88: [ 2673]: <-- [12:AT+FCLASS=1\r]
Aug 14 09:24:06.02: [ 2673]: --> [2:OK]
Aug 14 09:24:06.02: [ 2673]: <-- [12:AT+FCLASS=0\r]
Aug 14 09:24:06.16: [ 2673]: --> [2:OK]
Aug 14 09:24:06.16: [ 2673]: <-- [5:ATM0\r]
Aug 14 09:24:06.30: [ 2673]: --> [2:OK]
Aug 14 09:24:06.30: [ 2673]: STATE CHANGE: RUNNING -> SENDING
Aug 14 09:24:06.30: [ 2673]: MODEM input buffering enabled
Aug 14 09:24:06.30: [ 2673]: <-- [12:AT+FCLASS=1\r]
Aug 14 09:24:06.54: [ 2673]: --> [2:OK]
Aug 14 09:24:06.54: [ 2673]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Aug 14 09:24:06.57: [ 2673]: DIAL 28812370
Aug 14 09:24:06.57: [ 2673]: <-- [13:ATDT28812370\r]
Aug 14 09:24:20.47: [ 2673]: --> [7:CONNECT]
Aug 14 09:24:20.47: [ 2673]: MODEM input buffering disabled
Aug 14 09:24:22.10: [ 2673]: --> HDLC<28:FF C0 04 00 00 84 80 32 40 94 94 C0 F9 5C 87 80 F0 80 70 80 80 80 54 40 AE 10 B7 8D>

Aug 14 09:24:22.10: [ 2673]: --> [2:OK]
Aug 14 09:24:22.10: [ 2673]: REMOTE NSF "00 00 21 01 4C 02 29 29 03 9F 3A E1 01 0F 01 0E 01 01 01 2A 02 75 08 ED"
Aug 14 09:24:22.10: [ 2673]: NSF remote fax equipment: Lanier
Aug 14 09:24:22.10: [ 2673]: <-- [9:AT+FRH=3\r]
Aug 14 09:24:22.12: [ 2673]: --> [7:CONNECT]
Aug 14 09:24:22.79: [ 2673]: --> HDLC<25:FF C0 02 AC 0C 0C AC 9C 1C 1C 4C 04 04 04 04 04 04 04 04 04 04 04 04 A0 7B>
Aug 14 09:24:22.79: [ 2673]: --> [2:OK]
Aug 14 09:24:22.79: [ 2673]: REMOTE CSI "28895005"
Aug 14 09:24:22.79: [ 2673]: <-- [9:AT+FRH=3\r]
Aug 14 09:24:22.81: [ 2673]: --> [7:CONNECT]
Aug 14 09:24:23.09: [ 2673]: --> HDLC<9:FF C8 01 00 73 17 22 AD FF>
Aug 14 09:24:23.09: [ 2673]: --> [2:OK]
Aug 14 09:24:23.09: [ 2673]: REMOTE best rate 9600 bit/s
Aug 14 09:24:23.09: [ 2673]: REMOTE max page width 1728 pixels in 215 mm
Aug 14 09:24:23.09: [ 2673]: REMOTE max unlimited page length
Aug 14 09:24:23.09: [ 2673]: REMOTE best vres 7.7 line/mm
Aug 14 09:24:23.09: [ 2673]: REMOTE best format 2-D MMR
Aug 14 09:24:23.09: [ 2673]: REMOTE supports T.30 Annex A, ECM
Aug 14 09:24:23.09: [ 2673]: REMOTE best 10 ms, 5 ms/scanline
Aug 14 09:24:23.09: [ 2673]: USE 9600 bit/s
Aug 14 09:24:23.09: [ 2673]: USE 10 ms, 5 ms/scanline
Aug 14 09:24:23.09: [ 2673]: SEND file "docq/doc25.ps;30"
Aug 14 09:24:23.10: [ 2673]: USE page width 1728 pixels in 215 mm
Aug 14 09:24:23.10: [ 2673]: USE unlimited page length
Aug 14 09:24:23.10: [ 2673]: USE 3.85 line/mm
Aug 14 09:24:23.10: [ 2673]: USE 1-D MR
Aug 14 09:24:23.10: [ 2673]: SEND training at v.29 9600 bit/s
Aug 14 09:24:23.10: [ 2673]: <-- [9:AT+FTH=3\r]
Aug 14 09:24:23.29: [ 2673]: --> [7:CONNECT]
Aug 14 09:24:23.29: [ 2673]: <-- HDLC<23:FF C0 C2 1E 86 62 AE 2C CE 76 86 04 04 04 04 04 04 04 04 04 04 04 04>
Aug 14 09:24:23.29: [ 2673]: <-- data [23]
Aug 14 09:24:23.29: [ 2673]: <-- data [2]
Aug 14 09:24:23.32: [ 2673]: --> [7:CONNECT]
Aug 14 09:24:23.32: [ 2673]: <-- HDLC<6:FF C8 C1 00 60 14>
Aug 14 09:24:23.32: [ 2673]: <-- data [6]
Aug 14 09:24:23.32: [ 2673]: <-- data [2]
Aug 14 09:24:25.27: [ 2673]: --> [2:OK]
Aug 14 09:24:25.27: [ 2673]: <-- [9:AT+FTS=7\r]
Aug 14 09:24:25.36: [ 2673]: --> [2:OK]
Aug 14 09:24:25.36: [ 2673]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 14 09:24:25.36: [ 2673]: <-- [10:AT+FTM=96\r]
Aug 14 09:24:25.68: [ 2673]: --> [7:CONNECT]
Aug 14 09:24:25.68: [ 2673]: <-- data [1024]
Aug 14 09:24:25.68: [ 2673]: <-- data [776]
Aug 14 09:24:25.68: [ 2673]: <-- data [2]
Aug 14 09:24:27.22: [ 2673]: --> [2:OK]
Aug 14 09:24:27.22: [ 2673]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 14 09:24:27.22: [ 2673]: <-- [9:AT+FRH=3\r]
Aug 14 09:24:27.92: [ 2673]: --> [7:CONNECT]
Aug 14 09:24:28.89: [ 2673]: --> HDLC<5:FF C8 21 57 BE>
Aug 14 09:24:28.89: [ 2673]: --> [2:OK]
Aug 14 09:24:28.89: [ 2673]: TRAINING succeeded
Aug 14 09:24:28.89: [ 2673]: DELAY 75 ms
Aug 14 09:24:28.97: [ 2673]: <-- [10:AT+FTM=96\r]
Aug 14 09:24:29.32: [ 2673]: --> [7:CONNECT]
Aug 14 09:24:29.32: [ 2673]: SEND begin page
Aug 14 09:24:29.32: [ 2673]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 14 09:24:29.33: [ 2673]: <-- data [1030]
Aug 14 09:24:29.33: [ 2673]: <-- data [1024]
Aug 14 09:24:29.33: [ 2673]: <-- data [1025]
Aug 14 09:24:29.33: [ 2673]: <-- data [1024]
Aug 14 09:24:29.33: [ 2673]: <-- data [1028]
Aug 14 09:24:31.32: [ 2673]: <-- data [1031]
Aug 14 09:24:31.32: [ 2673]: <-- data [1028]
Aug 14 09:24:31.32: [ 2673]: <-- data [1031]
Aug 14 09:24:33.32: [ 2673]: <-- data [1026]
Aug 14 09:24:33.32: [ 2673]: <-- data [1024]
Aug 14 09:24:33.32: [ 2673]: <-- data [1033]
Aug 14 09:24:33.32: [ 2673]: <-- data [1027]
Aug 14 09:24:34.62: [ 2673]: <-- data [626]
Aug 14 09:24:36.62: [ 2673]: SENT 12911 bytes of data
Aug 14 09:24:36.62: [ 2673]: <-- data [1026]
Aug 14 09:24:36.63: [ 2673]: <-- data [1027]
Aug 14 09:24:36.63: [ 2673]: <-- data [1026]
Aug 14 09:24:38.62: [ 2673]: <-- data [1025]
Aug 14 09:24:38.62: [ 2673]: <-- data [1031]
Aug 14 09:24:40.62: [ 2673]: <-- data [1026]
Aug 14 09:24:40.62: [ 2673]: <-- data [1025]
Aug 14 09:24:42.62: [ 2673]: <-- data [1028]
Aug 14 09:24:42.62: [ 2673]: <-- data [1024]
Aug 14 09:24:42.62: [ 2673]: <-- data [1025]
Aug 14 09:24:44.62: [ 2673]: <-- data [1027]
Aug 14 09:24:44.62: [ 2673]: <-- data [493]
Aug 14 09:24:44.62: [ 2673]: SENT 11757 bytes of data
Aug 14 09:24:44.62: [ 2673]: SEND 1D RTC
Aug 14 09:24:44.62: [ 2673]: <-- data [29]
Aug 14 09:24:44.62: [ 2673]: <-- data [2]
Aug 14 09:24:44.62: [ 2673]: SEND end page
Aug 14 09:24:49.94: [ 2673]: --> [2:OK]
Aug 14 09:24:49.94: [ 2673]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 14 09:24:49.94: [ 2673]: <-- [9:AT+FTS=7\r]
Aug 14 09:24:50.03: [ 2673]: --> [2:OK]
Aug 14 09:24:50.03: [ 2673]: SEND send MPS (more pages, same document)
Aug 14 09:24:50.03: [ 2673]: <-- [9:AT+FTH=3\r]
Aug 14 09:24:50.19: [ 2673]: --> [7:CONNECT]
Aug 14 09:24:50.19: [ 2673]: <-- HDLC<3:FF C8 F2>
Aug 14 09:24:50.19: [ 2673]: <-- data [3]
Aug 14 09:24:50.20: [ 2673]: <-- data [2]
Aug 14 09:24:51.37: [ 2673]: --> [2:OK]
Aug 14 09:24:51.37: [ 2673]: <-- [9:AT+FRH=3\r]
Aug 14 09:24:51.92: [ 2673]: --> [7:CONNECT]
Aug 14 09:24:52.75: [ 2673]: --> HDLC<5:FF C8 31 45 8F>
Aug 14 09:24:52.75: [ 2673]: --> [2:OK]
Aug 14 09:24:52.75: [ 2673]: SEND recv MCF (message confirmation)
Aug 14 09:24:52.75: [ 2673]: SEND FAX (00000044): FROM root@hostname TO 28812370 (page 1 of 4 sent in 0:29)
Aug 14 09:24:52.76: [ 2673]: USE page width 1728 pixels in 215 mm
Aug 14 09:24:52.76: [ 2673]: USE unlimited page length
Aug 14 09:24:52.76: [ 2673]: USE 3.85 line/mm
Aug 14 09:24:52.76: [ 2673]: USE 1-D MR
Aug 14 09:24:52.76: [ 2673]: DELAY 75 ms
Aug 14 09:24:52.83: [ 2673]: <-- [10:AT+FTM=96\r]
Aug 14 09:24:53.18: [ 2673]: --> [7:CONNECT]
Aug 14 09:24:53.18: [ 2673]: SEND begin page
Aug 14 09:24:53.18: [ 2673]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 14 09:24:53.19: [ 2673]: <-- data [1028]
Aug 14 09:24:53.19: [ 2673]: <-- data [1024]
Aug 14 09:24:53.19: [ 2673]: <-- data [1029]
Aug 14 09:24:53.19: [ 2673]: <-- data [1025]
Aug 14 09:24:53.19: [ 2673]: <-- data [1026]
Aug 14 09:24:55.18: [ 2673]: <-- data [1026]
Aug 14 09:24:55.18: [ 2673]: <-- data [1026]
Aug 14 09:24:55.18: [ 2673]: <-- data [1029]
Aug 14 09:24:57.18: [ 2673]: <-- data [1024]
Aug 14 09:24:57.18: [ 2673]: <-- data [1027]
Aug 14 09:24:57.18: [ 2673]: <-- data [1025]
Aug 14 09:24:57.18: [ 2673]: <-- data [1026]
Aug 14 09:24:58.47: [ 2673]: <-- data [640]
Aug 14 09:25:00.47: [ 2673]: SENT 12925 bytes of data
Aug 14 09:25:00.47: [ 2673]: <-- data [1029]
Aug 14 09:25:00.47: [ 2673]: <-- data [1026]
Aug 14 09:25:00.47: [ 2673]: <-- data [1024]
Aug 14 09:25:02.47: [ 2673]: <-- data [1020]
Aug 14 09:25:02.47: [ 2673]: SENT 4090 bytes of data
Aug 14 09:25:02.47: [ 2673]: SEND 1D RTC
Aug 14 09:25:02.47: [ 2673]: <-- data [29]
Aug 14 09:25:02.47: [ 2673]: <-- data [2]
Aug 14 09:25:02.47: [ 2673]: SEND end page
Aug 14 09:25:07.42: [ 2673]: --> [2:OK]
Aug 14 09:25:07.42: [ 2673]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 14 09:25:07.42: [ 2673]: <-- [9:AT+FTS=7\r]
Aug 14 09:25:07.51: [ 2673]: --> [2:OK]
Aug 14 09:25:07.51: [ 2673]: SEND send MPS (more pages, same document)
Aug 14 09:25:07.51: [ 2673]: <-- [9:AT+FTH=3\r]
Aug 14 09:25:07.67: [ 2673]: --> [7:CONNECT]
Aug 14 09:25:07.67: [ 2673]: <-- HDLC<3:FF C8 F2>
Aug 14 09:25:07.67: [ 2673]: <-- data [3]
Aug 14 09:25:07.67: [ 2673]: <-- data [2]
Aug 14 09:25:08.85: [ 2673]: --> [2:OK]
Aug 14 09:25:08.85: [ 2673]: <-- [9:AT+FRH=3\r]
Aug 14 09:25:09.16: [ 2673]: --> [7:CONNECT]
Aug 14 09:25:10.24: [ 2673]: --> HDLC<5:FF C8 31 45 8F>
Aug 14 09:25:10.24: [ 2673]: --> [2:OK]
Aug 14 09:25:10.24: [ 2673]: SEND recv MCF (message confirmation)
Aug 14 09:25:10.24: [ 2673]: SEND FAX (00000044): FROM root@hostname TO 28812370 (page 2 of 4 sent in 0:18)
Aug 14 09:25:10.24: [ 2673]: USE page width 1728 pixels in 215 mm
Aug 14 09:25:10.25: [ 2673]: USE unlimited page length
Aug 14 09:25:10.25: [ 2673]: USE 3.85 line/mm
Aug 14 09:25:10.25: [ 2673]: USE 1-D MR
Aug 14 09:25:10.25: [ 2673]: DELAY 75 ms
Aug 14 09:25:10.32: [ 2673]: <-- [10:AT+FTM=96\r]
Aug 14 09:25:10.67: [ 2673]: --> [7:CONNECT]
Aug 14 09:25:10.67: [ 2673]: SEND begin page
Aug 14 09:25:10.67: [ 2673]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 14 09:25:10.68: [ 2673]: <-- data [1029]
Aug 14 09:25:10.68: [ 2673]: <-- data [1024]
Aug 14 09:25:10.68: [ 2673]: <-- data [1027]
Aug 14 09:25:10.68: [ 2673]: <-- data [1026]
Aug 14 09:25:10.68: [ 2673]: <-- data [1028]
Aug 14 09:25:12.67: [ 2673]: <-- data [1026]
Aug 14 09:25:12.67: [ 2673]: <-- data [1025]
Aug 14 09:25:12.67: [ 2673]: <-- data [1027]
Aug 14 09:25:14.67: [ 2673]: <-- data [1030]
Aug 14 09:25:14.67: [ 2673]: <-- data [1025]
Aug 14 09:25:14.67: [ 2673]: <-- data [1026]
Aug 14 09:25:14.67: [ 2673]: <-- data [1026]
Aug 14 09:25:15.96: [ 2673]: <-- data [647]
Aug 14 09:25:17.96: [ 2673]: SENT 12935 bytes of data
Aug 14 09:25:17.96: [ 2673]: <-- data [1028]
Aug 14 09:25:17.96: [ 2673]: <-- data [1027]
Aug 14 09:25:17.96: [ 2673]: <-- data [1026]
Aug 14 09:25:19.96: [ 2673]: <-- data [1028]
Aug 14 09:25:19.96: [ 2673]: <-- data [433]
Aug 14 09:25:19.96: [ 2673]: SENT 4529 bytes of data
Aug 14 09:25:19.96: [ 2673]: SEND 1D RTC
Aug 14 09:25:19.96: [ 2673]: <-- data [29]
Aug 14 09:25:19.96: [ 2673]: <-- data [2]
Aug 14 09:25:19.96: [ 2673]: SEND end page
Aug 14 09:25:25.28: [ 2673]: --> [2:OK]
Aug 14 09:25:25.28: [ 2673]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 14 09:25:25.28: [ 2673]: <-- [9:AT+FTS=7\r]
Aug 14 09:25:25.37: [ 2673]: --> [2:OK]
Aug 14 09:25:25.37: [ 2673]: SEND send MPS (more pages, same document)
Aug 14 09:25:25.37: [ 2673]: <-- [9:AT+FTH=3\r]
Aug 14 09:25:25.53: [ 2673]: --> [7:CONNECT]
Aug 14 09:25:25.53: [ 2673]: <-- HDLC<3:FF C8 F2>
Aug 14 09:25:25.53: [ 2673]: <-- data [3]
Aug 14 09:25:25.53: [ 2673]: <-- data [2]
Aug 14 09:25:26.71: [ 2673]: --> [2:OK]
Aug 14 09:25:26.71: [ 2673]: <-- [9:AT+FRH=3\r]
Aug 14 09:25:27.12: [ 2673]: --> [7:CONNECT]
Aug 14 09:25:28.09: [ 2673]: --> HDLC<5:FF C8 31 45 8F>
Aug 14 09:25:28.09: [ 2673]: --> [2:OK]
Aug 14 09:25:28.09: [ 2673]: SEND recv MCF (message confirmation)
Aug 14 09:25:28.09: [ 2673]: SEND FAX (00000044): FROM root@hostname TO 28812370 (page 3 of 4 sent in 0:18)
Aug 14 09:25:28.09: [ 2673]: USE page width 1728 pixels in 215 mm
Aug 14 09:25:28.09: [ 2673]: USE unlimited page length
Aug 14 09:25:28.10: [ 2673]: USE 3.85 line/mm
Aug 14 09:25:28.10: [ 2673]: USE 1-D MR
Aug 14 09:25:28.10: [ 2673]: DELAY 75 ms
Aug 14 09:25:28.17: [ 2673]: <-- [10:AT+FTM=96\r]
Aug 14 09:25:28.52: [ 2673]: --> [7:CONNECT]
Aug 14 09:25:28.52: [ 2673]: SEND begin page
Aug 14 09:25:28.52: [ 2673]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 14 09:25:28.53: [ 2673]: <-- data [1033]
Aug 14 09:25:28.53: [ 2673]: <-- data [1025]
Aug 14 09:25:28.53: [ 2673]: <-- data [1024]
Aug 14 09:25:28.53: [ 2673]: <-- data [1025]
Aug 14 09:25:28.53: [ 2673]: <-- data [1033]
Aug 14 09:25:30.52: [ 2673]: <-- data [890]
Aug 14 09:25:30.52: [ 2673]: SENT 6007 bytes of data
Aug 14 09:25:30.52: [ 2673]: SEND 1D RTC
Aug 14 09:25:30.52: [ 2673]: <-- data [29]
Aug 14 09:25:30.52: [ 2673]: <-- data [2]
Aug 14 09:25:30.52: [ 2673]: SEND end page
Aug 14 09:25:33.59: [ 2673]: --> [2:OK]
Aug 14 09:25:33.59: [ 2673]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 14 09:25:33.59: [ 2673]: <-- [9:AT+FTS=9\r]
Aug 14 09:25:33.70: [ 2673]: --> [2:OK]
Aug 14 09:25:33.70: [ 2673]: SEND send EOP (no more pages or documents)
Aug 14 09:25:33.70: [ 2673]: <-- [9:AT+FTH=3\r]
Aug 14 09:25:33.86: [ 2673]: --> [7:CONNECT]
Aug 14 09:25:33.86: [ 2673]: <-- HDLC<3:FF C8 F4>
Aug 14 09:25:33.86: [ 2673]: <-- data [3]
Aug 14 09:25:33.86: [ 2673]: <-- data [2]
Aug 14 09:25:35.04: [ 2673]: --> [2:OK]
Aug 14 09:25:35.04: [ 2673]: <-- [9:AT+FRH=3\r]
Aug 14 09:25:35.56: [ 2673]: --> [7:CONNECT]
Aug 14 09:25:36.43: [ 2673]: --> HDLC<5:FF C8 31 45 8F>
Aug 14 09:25:36.43: [ 2673]: --> [2:OK]
Aug 14 09:25:36.43: [ 2673]: SEND recv MCF (message confirmation)
Aug 14 09:25:36.43: [ 2673]: SEND FAX (00000044): FROM root@hostname TO 28812370 (page 4 of 4 sent in 0:08)
Aug 14 09:25:36.43: [ 2673]: SEND FAX (00000044): FROM root@hostname TO 28812370 (docq/doc25.ps;30 sent in 1:13)
Aug 14 09:25:36.44: [ 2673]: <-- [9:AT+FTH=3\r]
Aug 14 09:25:36.63: [ 2673]: --> [7:CONNECT]
Aug 14 09:25:36.63: [ 2673]: <-- HDLC<3:FF C8 DF>
Aug 14 09:25:36.63: [ 2673]: <-- data [3]
Aug 14 09:25:36.63: [ 2673]: <-- data [2]
Aug 14 09:25:37.81: [ 2673]: --> [2:OK]
Aug 14 09:25:37.81: [ 2673]: MODEM input buffering enabled
Aug 14 09:25:37.81: [ 2673]: <-- [5:ATH0\r]
Aug 14 09:25:38.05: [ 2673]: --> [2:OK]
Aug 14 09:25:38.05: [ 2673]: MODEM set DTR OFF
Aug 14 09:25:38.05: [ 2673]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Aug 14 09:25:38.05: [ 2673]: SESSION END

-----Original Message-----
From: KY Lui [mailto:kylui@pcgsys.com]
Sent: Wednesday, August 14, 2002 9:02 AM
To: 'Giulio Orsero'; hylafax-users@hylafax.org
Subject: Re: [hylafax-users] strange behavior...

what is the session tracing for? my existing value is 11
moreover what is the different between sendfax and faxsend?
it seems that i can use sendfax without problem but not faxsend.
Thanks
-----Original Message-----
From: Giulio Orsero [mailto:giulioo@pobox.com]
Sent: Tuesday, August 13, 2002 6:31 PM
To: hylafax-users@hylafax.org
Subject: Re: [hylafax-users] strange behavior...

On Tue, 13 Aug 2002 18:16:42 +0800, KY Lui <kylui@pcgsys.com> wrote:
>I try to send a fax (sendfax -n -d 123456 file)
>after a while, a confirmation mail is received and it told me that the fax
>is sent successfully.
>However, the fax cannot be received in the destination. (i am pretty sure
>that the fax machine is working properly in the destination side).
Add
SessionTracing:            0xFFF
to your config.<devid>, reproduce, send log you find in
/var/spool/hylafax/log/c*
--
giulioo@pobox.com
____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*