HylaFAX The world's most advanced open source fax server
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] one more log....

The previous log was of a transmission locked at 2400 baud because i was
trying to debug.. i figured i'd force to send slower and that might use a
differnet protocol or something (yes, grasping at straws).  Here is
another log, that wasn't constrained...

They all have the same chopped up, only get about 40% total of the fax...


Jul 07 01:11:20.85: [  932]: SESSION BEGIN 00000011 17029394116
Jul 07 01:11:20.85: [  932]: HylaFAX (tm) Version 4.1
Jul 07 01:11:20.85: [  932]: SEND FAX: JOB 9 DEST 9394116 COMMID 00000011
Jul 07 01:11:20.85: [  932]: DEVICE '/dev/cuaa0'
Jul 07 01:11:20.85: [  932]: MODEM set DTR OFF
Jul 07 01:11:20.85: [  932]: DELAY 75 ms
Jul 07 01:11:20.94: [  932]: MODEM set DTR ON
Jul 07 01:11:20.94: [  932]: DELAY 2600 ms
Jul 07 01:11:23.55: [  932]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
Jul 07 01:11:23.55: [  932]: MODEM flush i/o
Jul 07 01:11:23.55: [  932]: <-- [4:ATZ\r]
Jul 07 01:11:23.59: [  932]: --> [3:ATZ]
Jul 07 01:11:23.59: [  932]: --> [2:OK]
Jul 07 01:11:23.59: [  932]: <-- [5:ATE0\r]
Jul 07 01:11:23.60: [  932]: --> [4:ATE0]
Jul 07 01:11:23.60: [  932]: --> [2:OK]
Jul 07 01:11:23.60: [  932]: <-- [5:ATV1\r]
Jul 07 01:11:23.61: [  932]: --> [2:OK]
Jul 07 01:11:23.61: [  932]: <-- [5:ATQ0\r]
Jul 07 01:11:23.62: [  932]: --> [2:OK]
Jul 07 01:11:23.62: [  932]: <-- [7:ATS0=0\r]
Jul 07 01:11:23.63: [  932]: --> [2:OK]
Jul 07 01:11:23.63: [  932]: <-- [7:ATS8=2\r]
Jul 07 01:11:23.64: [  932]: --> [2:OK]
Jul 07 01:11:23.64: [  932]: <-- [8:ATS7=60\r]
Jul 07 01:11:23.65: [  932]: --> [2:OK]
Jul 07 01:11:23.65: [  932]: <-- [12:AT+FCLASS=1\r]
Jul 07 01:11:23.67: [  932]: --> [2:OK]
Jul 07 01:11:23.67: [  932]: <-- [5:ATM0\r]
Jul 07 01:11:23.68: [  932]: --> [2:OK]
Jul 07 01:11:23.68: [  932]: STATE CHANGE: RUNNING -> SENDING
Jul 07 01:11:23.68: [  932]: MODEM input buffering enabled
Jul 07 01:11:23.68: [  932]: Apply DialString rules to "9394116"
Jul 07 01:11:23.68: [  932]: --> return result "9394116"
Jul 07 01:11:23.68: [  932]: <-- [12:AT+FCLASS=1\r]
Jul 07 01:11:23.80: [  932]: --> [2:OK]
Jul 07 01:11:23.80: [  932]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Jul 07 01:11:23.80: [  932]: DIAL 9394116
Jul 07 01:11:23.80: [  932]: <-- [12:ATDT9394116\r]
Jul 07 01:11:33.17: [  932]: --> [7:CONNECT]
Jul 07 01:11:33.17: [  932]: MODEM input buffering disabled
Jul 07 01:11:34.71: [  932]: --> HDLC<25:FF C0 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 DC 53>
Jul 07 01:11:34.71: [  932]: --> [2:OK]
Jul 07 01:11:34.71: [  932]: REMOTE CSI ""
Jul 07 01:11:34.71: [  932]: <-- [9:AT+FRH=3\r]
Jul 07 01:11:34.73: [  932]: --> [7:CONNECT]
Jul 07 01:11:34.99: [  932]: --> HDLC<9:FF C8 01 00 72 1F 00 17 46>
Jul 07 01:11:35.00: [  932]: --> [2:OK]
Jul 07 01:11:35.00: [  932]: REMOTE best rate 9600 bit/s
Jul 07 01:11:35.00: [  932]: REMOTE max page width 1728 pixels in 215 mm
Jul 07 01:11:35.00: [  932]: REMOTE max unlimited page length
Jul 07 01:11:35.00: [  932]: REMOTE best vres 7.7 line/mm
Jul 07 01:11:35.00: [  932]: REMOTE best format 1-D MR
Jul 07 01:11:35.00: [  932]: REMOTE best 0 ms/scanline
Jul 07 01:11:35.00: [  932]: USE 9600 bit/s
Jul 07 01:11:35.00: [  932]: USE 0 ms/scanline
Jul 07 01:11:35.00: [  932]: SEND file "docq/doc9.cover;30"
Jul 07 01:11:35.00: [  932]: USE page width 1728 pixels in 215 mm
Jul 07 01:11:35.00: [  932]: USE unlimited page length
Jul 07 01:11:35.00: [  932]: USE 3.85 line/mm
Jul 07 01:11:35.00: [  932]: USE 1-D MR
Jul 07 01:11:35.00: [  932]: SEND training at v.29 9600 bit/s
Jul 07 01:11:35.00: [  932]: <-- [9:AT+FTH=3\r]
Jul 07 01:11:35.02: [  932]: --> [7:CONNECT]
Jul 07 01:11:35.02: [  932]: <-- HDLC<23:FF C0 C2 0E AE 2E A6 CA E6 76 96 16 2E F6 72 04 04 04 04 04 04 04 04>
Jul 07 01:11:35.02: [  932]: <-- data [23]
Jul 07 01:11:35.02: [  932]: <-- data [2]
Jul 07 01:11:37.23: [  932]: --> [7:CONNECT]
Jul 07 01:11:37.23: [  932]: <-- HDLC<6:FF C8 C1 00 60 1E>
Jul 07 01:11:37.23: [  932]: <-- data [6]
Jul 07 01:11:37.23: [  932]: <-- data [2]
Jul 07 01:11:37.71: [  932]: --> [2:OK]
Jul 07 01:11:37.71: [  932]: DELAY 75 ms
Jul 07 01:11:37.80: [  932]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jul 07 01:11:37.80: [  932]: <-- [10:AT+FTM=96\r]
Jul 07 01:11:37.82: [  932]: --> [7:CONNECT]
Jul 07 01:11:37.82: [  932]: <-- data [1024]
Jul 07 01:11:37.82: [  932]: <-- data [776]
Jul 07 01:11:37.82: [  932]: <-- data [2]
Jul 07 01:11:39.23: [  932]: --> [2:OK]
Jul 07 01:11:39.23: [  932]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jul 07 01:11:39.23: [  932]: <-- [9:AT+FRH=3\r]
Jul 07 01:11:39.64: [  932]: --> [7:CONNECT]
Jul 07 01:11:40.76: [  932]: --> HDLC<5:FF C8 22 67 DD>
Jul 07 01:11:40.76: [  932]: --> [2:OK]
Jul 07 01:11:40.76: [  932]: DELAY 1500 ms
Jul 07 01:11:42.27: [  932]: SEND training at v.29 7200 bit/s
Jul 07 01:11:42.27: [  932]: <-- [9:AT+FTH=3\r]
Jul 07 01:11:42.29: [  932]: --> [7:CONNECT]
Jul 07 01:11:42.29: [  932]: <-- HDLC<23:FF C0 C2 0E AE 2E A6 CA E6 76 96 16 2E F6 72 04 04 04 04 04 04 04 04>
Jul 07 01:11:42.29: [  932]: <-- data [23]
Jul 07 01:11:42.29: [  932]: <-- data [2]
Jul 07 01:11:44.50: [  932]: --> [7:CONNECT]
Jul 07 01:11:44.50: [  932]: <-- HDLC<6:FF C8 C1 00 70 1E>
Jul 07 01:11:44.50: [  932]: <-- data [6]
Jul 07 01:11:44.50: [  932]: <-- data [2]
Jul 07 01:11:44.98: [  932]: --> [2:OK]
Jul 07 01:11:44.98: [  932]: DELAY 75 ms
Jul 07 01:11:45.07: [  932]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jul 07 01:11:45.07: [  932]: <-- [10:AT+FTM=72\r]
Jul 07 01:11:45.09: [  932]: --> [7:CONNECT]
Jul 07 01:11:45.09: [  932]: <-- data [1024]
Jul 07 01:11:45.09: [  932]: <-- data [326]
Jul 07 01:11:45.09: [  932]: <-- data [2]
Jul 07 01:11:46.22: [  932]: --> [2:OK]
Jul 07 01:11:46.22: [  932]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jul 07 01:11:46.22: [  932]: <-- [9:AT+FRH=3\r]
Jul 07 01:11:46.62: [  932]: --> [7:CONNECT]
Jul 07 01:11:47.74: [  932]: --> HDLC<5:FF C8 22 67 DD>
Jul 07 01:11:47.74: [  932]: --> [2:OK]
Jul 07 01:11:47.74: [  932]: DELAY 1500 ms
Jul 07 01:11:49.25: [  932]: SEND training at v.27ter 4800 bit/s
Jul 07 01:11:49.25: [  932]: <-- [9:AT+FTH=3\r]
Jul 07 01:11:49.27: [  932]: --> [7:CONNECT]
Jul 07 01:11:49.27: [  932]: <-- HDLC<23:FF C0 C2 0E AE 2E A6 CA E6 76 96 16 2E F6 72 04 04 04 04 04 04 04 04>
Jul 07 01:11:49.27: [  932]: <-- data [23]
Jul 07 01:11:49.27: [  932]: <-- data [2]
Jul 07 01:11:51.48: [  932]: --> [7:CONNECT]
Jul 07 01:11:51.48: [  932]: <-- HDLC<6:FF C8 C1 00 50 1E>
Jul 07 01:11:51.48: [  932]: <-- data [6]
Jul 07 01:11:51.48: [  932]: <-- data [2]
Jul 07 01:11:51.96: [  932]: --> [2:OK]
Jul 07 01:11:51.96: [  932]: DELAY 75 ms
Jul 07 01:11:52.05: [  932]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jul 07 01:11:52.05: [  932]: <-- [10:AT+FTM=48\r]
Jul 07 01:11:52.07: [  932]: --> [7:CONNECT]
Jul 07 01:11:52.07: [  932]: <-- data [900]
Jul 07 01:11:52.07: [  932]: <-- data [2]
Jul 07 01:11:54.55: [  932]: --> [2:OK]
Jul 07 01:11:54.55: [  932]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jul 07 01:11:54.55: [  932]: <-- [9:AT+FRH=3\r]
Jul 07 01:11:54.89: [  932]: --> [7:CONNECT]
Jul 07 01:11:56.01: [  932]: --> HDLC<5:FF C8 21 57 BE>
Jul 07 01:11:56.01: [  932]: --> [2:OK]
Jul 07 01:11:56.01: [  932]: TRAINING succeeded
Jul 07 01:11:56.01: [  932]: <-- [10:AT+FTM=48\r]
Jul 07 01:11:56.03: [  932]: --> [7:CONNECT]
Jul 07 01:11:56.03: [  932]: SEND begin page
Jul 07 01:11:56.03: [  932]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jul 07 01:11:56.03: [  932]: <-- data [1038]
Jul 07 01:11:56.03: [  932]: <-- data [1032]
Jul 07 01:11:56.03: [  932]: <-- data [1033]
Jul 07 01:11:56.92: [  932]: <-- data [1031]
Jul 07 01:11:56.92: [  932]: <-- data [1046]
Jul 07 01:11:57.99: [  932]: <-- data [1038]
Jul 07 01:11:57.99: [  932]: <-- data [1055]
Jul 07 01:11:59.05: [  932]: <-- data [1049]
Jul 07 01:11:59.05: [  932]: <-- data [1058]
Jul 07 01:12:00.12: [  932]: <-- data [1051]
Jul 07 01:12:00.12: [  932]: <-- data [1031]
Jul 07 01:12:01.18: [  932]: <-- data [968]
Jul 07 01:12:01.18: [  932]: SENT 12232 bytes of data
Jul 07 01:12:01.18: [  932]: SEND 1D RTC
Jul 07 01:12:01.18: [  932]: <-- data [29]
Jul 07 01:12:01.18: [  932]: <-- data [2]
Jul 07 01:12:01.18: [  932]: SEND end page
Jul 07 01:12:04.04: [  932]: --> [2:OK]
Jul 07 01:12:04.04: [  932]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jul 07 01:12:04.04: [  932]: DELAY 75 ms
Jul 07 01:12:04.13: [  932]: SEND send MPS (more pages, same document)
Jul 07 01:12:04.13: [  932]: <-- [9:AT+FTH=3\r]
Jul 07 01:12:04.15: [  932]: --> [7:CONNECT]
Jul 07 01:12:04.15: [  932]: <-- HDLC<3:FF C8 F2>
Jul 07 01:12:04.15: [  932]: <-- data [3]
Jul 07 01:12:04.15: [  932]: <-- data [2]
Jul 07 01:12:05.82: [  932]: --> [2:OK]
Jul 07 01:12:05.82: [  932]: <-- [9:AT+FRH=3\r]
Jul 07 01:12:06.09: [  932]: --> [7:CONNECT]
Jul 07 01:12:07.21: [  932]: --> HDLC<5:FF C8 31 45 8F>
Jul 07 01:12:07.21: [  932]: --> [2:OK]
Jul 07 01:12:07.21: [  932]: SEND recv MCF (message confirmation)
Jul 07 01:12:07.21: [  932]: SEND FAX (00000011): FROM root@foodza.mcmunn.com TO 9394116 (page 1 of 4 sent in 0:32)
Jul 07 01:12:07.21: [  932]: SEND FAX (00000011): FROM root@foodza.mcmunn.com TO 9394116 (docq/doc9.cover;30 sent in 0:32)
Jul 07 01:12:07.21: [  932]: SEND file "docq/doc17.ps;30"
Jul 07 01:12:07.21: [  932]: USE page width 1728 pixels in 215 mm
Jul 07 01:12:07.21: [  932]: USE unlimited page length
Jul 07 01:12:07.21: [  932]: USE 3.85 line/mm
Jul 07 01:12:07.21: [  932]: USE 1-D MR
Jul 07 01:12:07.21: [  932]: <-- [10:AT+FTM=48\r]
Jul 07 01:12:07.23: [  932]: --> [7:CONNECT]
Jul 07 01:12:07.23: [  932]: SEND begin page
Jul 07 01:12:07.23: [  932]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jul 07 01:12:07.23: [  932]: <-- data [1029]
Jul 07 01:12:07.23: [  932]: <-- data [1025]
Jul 07 01:12:07.23: [  932]: <-- data [1030]
Jul 07 01:12:08.12: [  932]: <-- data [1029]
Jul 07 01:12:08.12: [  932]: <-- data [1031]
Jul 07 01:12:09.19: [  932]: <-- data [1026]
Jul 07 01:12:09.19: [  932]: <-- data [1027]
Jul 07 01:12:10.25: [  932]: <-- data [1026]
Jul 07 01:12:10.25: [  932]: <-- data [1027]
Jul 07 01:12:11.32: [  932]: <-- data [1025]
Jul 07 01:12:11.32: [  932]: <-- data [1025]
Jul 07 01:12:12.38: [  932]: <-- data [1027]
Jul 07 01:12:12.38: [  932]: <-- data [1024]
Jul 07 01:12:13.45: [  932]: <-- data [1025]
Jul 07 01:12:13.45: [  932]: <-- data [1026]
Jul 07 01:12:14.51: [  932]: <-- data [1026]
Jul 07 01:12:14.51: [  932]: <-- data [1025]
Jul 07 01:12:15.58: [  932]: <-- data [1027]
Jul 07 01:12:15.58: [  932]: <-- data [1025]
Jul 07 01:12:16.64: [  932]: <-- data [1027]
Jul 07 01:12:16.64: [  932]: <-- data [1025]
Jul 07 01:12:17.71: [  932]: <-- data [1025]
Jul 07 01:12:17.71: [  932]: <-- data [1027]
Jul 07 01:12:18.77: [  932]: <-- data [1025]
Jul 07 01:12:18.77: [  932]: <-- data [1026]
Jul 07 01:12:19.84: [  932]: <-- data [775]
Jul 07 01:12:19.84: [  932]: SENT 26375 bytes of data
Jul 07 01:12:19.84: [  932]: SEND 1D RTC
Jul 07 01:12:19.84: [  932]: <-- data [29]
Jul 07 01:12:19.84: [  932]: <-- data [2]
Jul 07 01:12:19.84: [  932]: SEND end page
Jul 07 01:12:21.59: [  932]: --> [2:OK]
Jul 07 01:12:21.59: [  932]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jul 07 01:12:21.59: [  932]: DELAY 75 ms
Jul 07 01:12:21.68: [  932]: SEND send MPS (more pages, same document)
Jul 07 01:12:21.68: [  932]: <-- [9:AT+FTH=3\r]
Jul 07 01:12:21.70: [  932]: --> [7:CONNECT]
Jul 07 01:12:21.70: [  932]: <-- HDLC<3:FF C8 F2>
Jul 07 01:12:21.70: [  932]: <-- data [3]
Jul 07 01:12:21.70: [  932]: <-- data [2]
Jul 07 01:12:23.37: [  932]: --> [2:OK]
Jul 07 01:12:23.37: [  932]: <-- [9:AT+FRH=3\r]
Jul 07 01:12:23.63: [  932]: --> [7:CONNECT]
Jul 07 01:12:24.75: [  932]: --> HDLC<5:FF C8 31 45 8F>
Jul 07 01:12:24.75: [  932]: --> [2:OK]
Jul 07 01:12:24.75: [  932]: SEND recv MCF (message confirmation)
Jul 07 01:12:24.75: [  932]: SEND FAX (00000011): FROM root@foodza.mcmunn.com TO 9394116 (page 2 of 4 sent in 0:17)
Jul 07 01:12:24.75: [  932]: USE page width 1728 pixels in 215 mm
Jul 07 01:12:24.75: [  932]: USE unlimited page length
Jul 07 01:12:24.75: [  932]: USE 3.85 line/mm
Jul 07 01:12:24.75: [  932]: USE 1-D MR
Jul 07 01:12:24.75: [  932]: <-- [10:AT+FTM=48\r]
Jul 07 01:12:24.77: [  932]: --> [7:CONNECT]
Jul 07 01:12:24.77: [  932]: SEND begin page
Jul 07 01:12:24.77: [  932]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jul 07 01:12:24.77: [  932]: <-- data [1028]
Jul 07 01:12:24.77: [  932]: <-- data [1025]
Jul 07 01:12:24.77: [  932]: <-- data [1030]
Jul 07 01:12:25.66: [  932]: <-- data [1029]
Jul 07 01:12:25.66: [  932]: <-- data [1031]
Jul 07 01:12:26.73: [  932]: <-- data [1026]
Jul 07 01:12:26.73: [  932]: <-- data [1025]
Jul 07 01:12:27.79: [  932]: <-- data [1024]
Jul 07 01:12:27.79: [  932]: <-- data [1024]
Jul 07 01:12:28.86: [  932]: <-- data [683]
Jul 07 01:12:28.86: [  932]: SENT 9899 bytes of data
Jul 07 01:12:28.86: [  932]: SEND 1D RTC
Jul 07 01:12:28.86: [  932]: <-- data [29]
Jul 07 01:12:28.86: [  932]: <-- data [2]
Jul 07 01:12:28.86: [  932]: SEND end page
Jul 07 01:12:30.39: [  932]: --> [2:OK]
Jul 07 01:12:30.39: [  932]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jul 07 01:12:30.39: [  932]: DELAY 75 ms
Jul 07 01:12:30.48: [  932]: SEND send MPS (more pages, same document)
Jul 07 01:12:30.48: [  932]: <-- [9:AT+FTH=3\r]
Jul 07 01:12:30.50: [  932]: --> [7:CONNECT]
Jul 07 01:12:30.50: [  932]: <-- HDLC<3:FF C8 F2>
Jul 07 01:12:30.50: [  932]: <-- data [3]
Jul 07 01:12:30.50: [  932]: <-- data [2]
Jul 07 01:12:32.17: [  932]: --> [2:OK]
Jul 07 01:12:32.17: [  932]: <-- [9:AT+FRH=3\r]
Jul 07 01:12:32.45: [  932]: --> [7:CONNECT]
Jul 07 01:12:33.56: [  932]: --> HDLC<5:FF C8 31 45 8F>
Jul 07 01:12:33.57: [  932]: --> [2:OK]
Jul 07 01:12:33.57: [  932]: SEND recv MCF (message confirmation)
Jul 07 01:12:33.57: [  932]: SEND FAX (00000011): FROM root@foodza.mcmunn.com TO 9394116 (page 3 of 4 sent in 0:09)
Jul 07 01:12:33.57: [  932]: USE page width 1728 pixels in 215 mm
Jul 07 01:12:33.57: [  932]: USE unlimited page length
Jul 07 01:12:33.57: [  932]: USE 3.85 line/mm
Jul 07 01:12:33.57: [  932]: USE 1-D MR
Jul 07 01:12:33.57: [  932]: <-- [10:AT+FTM=48\r]
Jul 07 01:12:33.59: [  932]: --> [7:CONNECT]
Jul 07 01:12:33.59: [  932]: SEND begin page
Jul 07 01:12:33.59: [  932]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Jul 07 01:12:33.59: [  932]: <-- data [1028]
Jul 07 01:12:33.59: [  932]: <-- data [1025]
Jul 07 01:12:33.59: [  932]: <-- data [1031]
Jul 07 01:12:34.48: [  932]: <-- data [1029]
Jul 07 01:12:34.48: [  932]: <-- data [1031]
Jul 07 01:12:35.55: [  932]: <-- data [1027]
Jul 07 01:12:35.55: [  932]: <-- data [1026]
Jul 07 01:12:36.61: [  932]: <-- data [1025]
Jul 07 01:12:36.61: [  932]: <-- data [1026]
Jul 07 01:12:37.68: [  932]: <-- data [1026]
Jul 07 01:12:37.68: [  932]: <-- data [1027]
Jul 07 01:12:38.74: [  932]: <-- data [1024]
Jul 07 01:12:38.74: [  932]: <-- data [1024]
Jul 07 01:12:39.81: [  932]: <-- data [1025]
Jul 07 01:12:39.81: [  932]: <-- data [1025]
Jul 07 01:12:40.87: [  932]: <-- data [1024]
Jul 07 01:12:40.87: [  932]: <-- data [1025]
Jul 07 01:12:41.94: [  932]: <-- data [1026]
Jul 07 01:12:41.94: [  932]: <-- data [1024]
Jul 07 01:12:43.00: [  932]: <-- data [1026]
Jul 07 01:12:43.00: [  932]: <-- data [1025]
Jul 07 01:12:44.07: [  932]: <-- data [1024]
Jul 07 01:12:44.07: [  932]: <-- data [1024]
Jul 07 01:12:45.13: [  932]: <-- data [1024]
Jul 07 01:12:45.13: [  932]: <-- data [1024]
Jul 07 01:12:46.20: [  932]: <-- data [1024]
Jul 07 01:12:46.20: [  932]: <-- data [1024]
Jul 07 01:12:47.26: [  932]: <-- data [1024]
Jul 07 01:12:47.26: [  932]: <-- data [1025]
Jul 07 01:12:48.33: [  932]: <-- data [1024]
Jul 07 01:12:48.33: [  932]: <-- data [1024]
Jul 07 01:12:49.39: [  932]: <-- data [1025]
Jul 07 01:12:49.39: [  932]: <-- data [1024]
Jul 07 01:12:50.46: [  932]: <-- data [1024]
Jul 07 01:12:50.46: [  932]: <-- data [1025]
Jul 07 01:12:51.52: [  932]: <-- data [1024]
Jul 07 01:12:51.52: [  932]: <-- data [1024]
Jul 07 01:12:52.58: [  932]: <-- data [1025]
Jul 07 01:12:52.59: [  932]: <-- data [1024]
Jul 07 01:12:53.65: [  932]: <-- data [1025]
Jul 07 01:12:53.65: [  932]: <-- data [1025]
Jul 07 01:12:54.71: [  932]: <-- data [196]
Jul 07 01:12:54.71: [  932]: SENT 42180 bytes of data
Jul 07 01:12:54.71: [  932]: SEND 1D RTC
Jul 07 01:12:54.71: [  932]: <-- data [29]
Jul 07 01:12:54.71: [  932]: <-- data [2]
Jul 07 01:12:54.71: [  932]: SEND end page
Jul 07 01:12:57.22: [  932]: --> [2:OK]
Jul 07 01:12:57.22: [  932]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Jul 07 01:12:57.22: [  932]: DELAY 95 ms
Jul 07 01:12:57.32: [  932]: SEND send EOP (no more pages or documents)
Jul 07 01:12:57.32: [  932]: <-- [9:AT+FTH=3\r]
Jul 07 01:12:57.34: [  932]: --> [7:CONNECT]
Jul 07 01:12:57.34: [  932]: <-- HDLC<3:FF C8 F4>
Jul 07 01:12:57.34: [  932]: <-- data [3]
Jul 07 01:12:57.34: [  932]: <-- data [2]
Jul 07 01:12:59.01: [  932]: --> [2:OK]
Jul 07 01:12:59.01: [  932]: <-- [9:AT+FRH=3\r]
Jul 07 01:12:59.28: [  932]: --> [7:CONNECT]
Jul 07 01:13:00.40: [  932]: --> HDLC<5:FF C8 31 45 8F>
Jul 07 01:13:00.40: [  932]: --> [2:OK]
Jul 07 01:13:00.40: [  932]: SEND recv MCF (message confirmation)
Jul 07 01:13:00.40: [  932]: SEND FAX (00000011): FROM root@foodza.mcmunn.com TO 9394116 (page 4 of 4 sent in 0:27)
Jul 07 01:13:00.40: [  932]: SEND FAX (00000011): FROM root@foodza.mcmunn.com TO 9394116 (docq/doc17.ps;30 sent in 0:53)
Jul 07 01:13:00.41: [  932]: <-- [9:AT+FTH=3\r]
Jul 07 01:13:00.42: [  932]: --> [7:CONNECT]
Jul 07 01:13:00.42: [  932]: <-- HDLC<3:FF C8 DF>
Jul 07 01:13:00.42: [  932]: <-- data [3]
Jul 07 01:13:00.42: [  932]: <-- data [2]
Jul 07 01:13:02.10: [  932]: --> [2:OK]
Jul 07 01:13:02.10: [  932]: MODEM input buffering enabled
Jul 07 01:13:02.10: [  932]: <-- [5:ATH0\r]
Jul 07 01:13:03.22: [  932]: --> [2:OK]
Jul 07 01:13:03.22: [  932]: MODEM set DTR OFF
Jul 07 01:13:03.22: [  932]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Jul 07 01:13:03.22: [  932]: SESSION END


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null

Project hosted by iFAX Solutions