Re: [hylafax-users] U.S. Robotics 56K Message Settings...

["Alain Siani" <ASiani@wanadoo.fr>]

sometimes..it run
frequently error (99%) : Timeout or Busy

thanks a lot
alain

ati4
U.S. Robotics 56K Message Settings...

   B0  E1  F1  L1  M0  Q0  V1  X4  Y0
   BAUD=38400  PARITY=N  WORDLEN=8
   DIAL=PULSE   ON HOOK

   &A3  &B1  &C1  &D2  &H1  &I0  &K1
   &M4  &N0  &P1  &R2  &S0  &T5  &U0  &Y1

   S00=000  S01=000  S02=043  S03=013  S04=010  S05=008  S06=002
   S07=045  S08=002  S09=006  S10=014  S11=070  S12=050  S13=000
   S15=000  S16=000  S18=000  S19=000  S21=010  S22=017  S23=019
   S25=005  S27=017  S28=008  S29=020  S30=000  S31=128  S32=002
   S33=000  S34=000  S35=000  S36=014  S38=000  S39=012  S40=000
   S41=004  S42=000  S43=112

   LAST DIALED #:

OK

ati7
Configuration Profile...

Product type           France External
Product ID:            06566800
Options                V32bis,V.34+,x2,V.90
Fax Options            Class 1/Class 2.0
Voice Options          Speaker Phone, TAD
Clock Freq             92.0Mhz
EPROM                  256k
RAM                    32k

FLASH date             2/13/98
FLASH rev              12.1.12

DSP date               2/13/98
DSP rev                12.1.12

OK



config.ttyS1

# $Id: usr-xon,v 1.6 2002/04/07 20:29:27 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names
of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and XON/XOFF flow control.
#
#
CountryCode:            33
AreaCode:               4
FAXNumber:              +33.xxxxxxxx
LongDistancePrefix:     0
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      0
SpeakerVolume:          on
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        +33.xxxxxxxxx
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use class 1 interface
ModemRate:              9600            # rate for DCE-DTE communication
ModemFlowControl:       xonxoff         # hardware flow control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or
not)
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow
control
ModemResultCodesCmd:    ATQ0X4          # enable result codes
#
ModemMfrQueryCmd:       !USR
ModemModelQueryCmd:     ATI3
ModemRevQueryCmd:       ATI7            # XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow control
Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow
control
Class1SFLOCmd:          ""              # modem does this automatically
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:        AT+FCLASS=0     # leave modem idling in class 0
ModemAnswerCmd:         AT+FCLASS=1A    # answer in Class 1
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0


















-----Message d'origine-----
De : hylafax-users-bounce@hylafax.org
[mailto:hylafax-users-bounce@hylafax.org]De la part de Pedro Rocadas
Envoye : jeudi 20 juin 2002 15:42
A : hylafax-users@hylafax.org
Objet : Re: [hylafax-users] U.S. Robotics 56K Message Settings...


--- Alain Siani <ASiani@wanadoo.fr> wrote:
> I have a lot of problem grrrrrrrrr.....
>
>
> JID  Pri S  Owner Number       Pages Dials     TTS
> Status
> 3    126 S   uucp 00491598950   0:1   1:12   12:53
> No answer (T.30 T1 timeou
>
>
> thks a lot
> Alain

Jay is one of the guys who can give you the best
technical explanation to that message. But is a
comunication issue, like the remote fax machine is not
answering(?), no fax at all(?), there is a fax machine
that answer but unable to connect...oh, and you
configure that USR modem in Class1 right?

__________________________________________________
Do You Yahoo!?
Yahoo! - Official partner of 2002 FIFA World Cup
http://fifaworldcup.yahoo.com

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null