[hylafax-users] Trouble Receiving with Acceleport RAS 8

[Dave Higgins <supradave@earthlink.net>]

I'm having trouble receiving faxes on a Digi Acceleport RAS 8.

It is a Red Hat 7.2 installation on Dell hardware.  I have the drivers 
installed and the modem appears to function properly (can dial in and 
out).  When I receive a fax on the Digi card, I only get (mostly) 1 or a 
few lines of data, albeit incorrect.

As the logs indicate, I have tried to deal with Flow Control.  I have 
also set the modem in the various modes, i.e. Class 1, 2 or 2.0 with no 
success.

 From the Digi documentation I have set AT&K6 (both rtscts and xonxoff) 
(default for faxing) where the default is something else.

What I am wondering, are the AT commands that HylaFAX grabs from the 
faxaddmodem correct?  Should the Digi board work "out of the box" in 
HylaFAX, i.e. receive without additional setup?  If not, how do I get it 
to receive properly?

Also, I have setup a modem on ttyS0 and had success with receiving a fax 
without any changes to any files (other than /etc/inittab).

Basically, the log looks as follows . . .

c0000026
Jun 03 10:16:09.25: [ 1130]: --> [7:CONNECT]
Jun 03 10:16:09.25: [ 1130]: RECV: begin page
Jun 03 10:16:09.28: [ 1130]: RECV: send trigger 022
Jun 03 10:16:09.28: [ 1130]: <-- data [1]
Jun 03 10:16:14.71: [ 1130]: RECV: 6503 bytes of data, 1 total lines
Jun 03 10:16:14.73: [ 1130]: --> [17:+FPS:1,1051,0,0,0]
Jun 03 10:16:14.73: [ 1130]: --> [6:+FET:2]
Jun 03 10:16:14.73: [ 1130]: RECV recv EOP (no more pages or documents)
Jun 03 10:16:14.73: [ 1130]: --> [2:OK]
Jun 03 10:16:14.73: [ 1130]: RECV send MCF (message confirmation)

c0000015
May 30 11:46:10.77: [ 7785]: --> [7:CONNECT]
May 30 11:46:10.77: [ 7785]: RECV: begin page
May 30 11:46:10.77: [ 7785]: MODEM set XON/XOFF/FLUSH: input ignored, 
output generated
May 30 11:46:10.79: [ 7785]: RECV: send trigger 022
May 30 11:46:10.79: [ 7785]: <-- data [1]
May 30 11:46:12.06: [ 7785]: RECV/CQ: Bad 1D pixel count, row 0, got 
1840, expected 1728
May 30 11:46:12.24: [ 7785]: RECV/CQ: Bad 1D pixel count, row 1, got 
2371, expected 1728
May 30 11:46:13.01: [ 7785]: RECV/CQ: Bad 1D pixel count, row 2, got 
4742, expected 1728
May 30 11:46:13.57: [ 7785]: RECV/CQ: Bad 1D pixel count, row 3, got 
2409, expected 1728
May 30 11:46:16.17: [ 7785]: RECV: 4173 bytes of data, 4 total lines
May 30 11:46:16.17: [ 7785]: MODEM set XON/XOFF/DRAIN: input 
interpreted, output disabled
May 30 11:46:16.19: [ 7785]: --> [26:+FHR: FF 13 BF 2F 00 00 18]
May 30 11:46:16.19: [ 7785]: --> [17:+FPS:1,1051,0,0,0]
May 30 11:46:16.19: [ 7785]: --> [6:+FET:2]
May 30 11:46:16.19: [ 7785]: RECV recv EOP (no more pages or documents)
May 30 11:46:16.19: [ 7785]: --> [2:OK]
May 30 11:46:16.19: [ 7785]: RECV send MCF (message confirmation)

Thanks,
Dave


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null