[hylafax-users] receiving 2nd page resulting in "no carrier"

["Halter, B" <B.Halter@t-systems.com>]

Hello,

I�m still having trouble with sedlbaur speed fax+ pci card. Now we are able to receive the first page  of three. Just before the second page is about to get received the modem get "no carrier". May we have some trouble with our PBX? The ISDN-Modem is connected to an internal S0-Bus.

Here is the log:

May 16 15:58:46.07: [26460]: SESSION BEGIN 00000018 495219675224
May 16 15:58:46.07: [26460]: HylaFAX (tm) Version 4.1.2
May 16 15:58:46.07: [26460]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
May 16 15:58:46.07: [26460]: <-- [4:ATA\r]
May 16 15:58:51.28: [26460]: --> [7:CONNECT]
May 16 15:58:51.28: [26460]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyI0'
May 16 15:58:51.28: [26460]: MODEM input buffering enabled
May 16 15:58:51.28: [26460]: RECV FAX: begin
May 16 15:58:51.28: [26460]: MODEM input buffering disabled
May 16 15:58:51.28: [26460]: <-- data [23]
May 16 15:58:51.28: [26460]: <-- data [2]
May 16 15:58:51.33: [26460]: --> [7:CONNECT]
May 16 15:58:51.33: [26460]: <-- data [10]
May 16 15:58:51.33: [26460]: <-- data [2]
May 16 15:58:52.44: [26460]: --> [2:OK]
May 16 15:58:52.44: [26460]: <-- [9:AT+FRH=3\r]
May 16 15:58:52.75: [26460]: --> [7:CONNECT]
May 16 15:58:54.37: [26460]: --> [2:OK]
May 16 15:58:54.37: [26460]: REMOTE TSI "05219675218"
May 16 15:58:54.37: [26460]: <-- [9:AT+FRH=3\r]
May 16 15:58:54.38: [26460]: --> [7:CONNECT]
May 16 15:58:54.67: [26460]: --> [2:OK]
May 16 15:58:54.67: [26460]: REMOTE wants 9600 bit/s
May 16 15:58:54.67: [26460]: REMOTE wants page width 1728 pixels in 215 mm
May 16 15:58:54.67: [26460]: REMOTE wants unlimited page length 
May 16 15:58:54.67: [26460]: REMOTE wants 3.85 line/mm
May 16 15:58:54.67: [26460]: REMOTE wants 2-D MR
May 16 15:58:54.67: [26460]: RECV training at v.29 9600 bit/s
May 16 15:58:54.67: [26460]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
May 16 15:58:54.67: [26460]: <-- [10:AT+FRM=96\r]
May 16 15:58:55.02: [26460]: --> [7:CONNECT]
May 16 15:58:56.62: [26460]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
May 16 15:58:56.62: [26460]: RECV: TCF 1919 bytes, 5% non-zero, 1812 zero-run
May 16 15:58:56.62: [26460]: --> [10:NO CARRIER]
May 16 15:58:56.62: [26460]: DELAY 75 ms
May 16 15:58:56.70: [26460]: TRAINING succeeded
May 16 15:58:56.70: [26460]: <-- [9:AT+FTH=3\r]
May 16 15:58:58.33: [26460]: --> [7:CONNECT]
May 16 15:58:58.33: [26460]: <-- data [3]
May 16 15:58:58.33: [26460]: <-- data [2]
May 16 15:58:58.59: [26460]: --> [2:OK]
May 16 15:58:58.59: [26460]: MODEM input buffering enabled
May 16 15:58:58.59: [26460]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
May 16 15:58:58.59: [26460]: <-- [10:AT+FRM=96\r]
May 16 15:58:59.19: [26460]: --> [7:CONNECT]
May 16 15:58:59.19: [26460]: RECV: begin page
May 16 15:59:29.91: [26460]: RECV: 1135 total lines, 0 bad lines, 0 consecutive bad lines
May 16 15:59:29.91: [26460]: RECV: end page
May 16 15:59:29.91: [26460]: --> [10:NO CARRIER]
May 16 15:59:29.91: [26460]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
May 16 15:59:29.91: [26460]: MODEM input buffering disabled
May 16 15:59:29.91: [26460]: <-- [9:AT+FRH=3\r]
May 16 15:59:29.92: [26460]: --> [7:FCERROR]
May 16 15:59:44.61: [26460]: --> [10:NO CARRIER]
May 16 15:59:44.61: [26460]: MODEM No carrier
May 16 15:59:44.61: [26460]: <-- [9:AT+FRH=3\r]
May 16 15:59:44.62: [26460]: --> [5:ERROR]
May 16 15:59:44.62: [26460]: MODEM Command error
May 16 15:59:44.62: [26460]: <-- [9:AT+FRH=3\r]
May 16 15:59:44.63: [26460]: --> [5:ERROR]
May 16 15:59:44.63: [26460]: MODEM Command error
May 16 15:59:44.63: [26460]: <-- [9:AT+FRH=3\r]
May 16 15:59:44.64: [26460]: --> [5:ERROR]
May 16 15:59:44.64: [26460]: MODEM Command error
May 16 15:59:44.64: [26460]: <-- [9:AT+FRH=3\r]
May 16 15:59:44.65: [26460]: --> [5:ERROR]
May 16 15:59:44.65: [26460]: MODEM Command error
May 16 15:59:44.65: [26460]: <-- [9:AT+FRH=3\r]
May 16 15:59:44.66: [26460]: --> [5:ERROR]

[ the same error-block for more than 100 times ]

May 16 15:59:51.99: [26460]: <-- [9:AT+FRH=3\r]
May 16 15:59:52.00: [26460]: --> [5:ERROR]
May 16 15:59:52.00: [26460]: MODEM Command error
May 16 15:59:52.00: [26460]: RECV FAX (00000018): recvq/fax00010.tif from 05219675218, route to <unspecified>, 0 pages in 1:01
May 16 15:59:52.02: [26460]: RECV FAX: T.30 T2 timeout, expected page not received
May 16 15:59:52.02: [26460]: <-- [9:AT+FTH=3\r]
May 16 15:59:52.02: [26460]: --> [5:ERROR]
May 16 15:59:52.02: [26460]: MODEM input buffering enabled
May 16 15:59:52.02: [26460]: RECV FAX (00000018): session with 05219675218 terminated abnormally: T.30 T2 timeout, expected page not received
May 16 15:59:52.02: [26460]: RECV FAX: bin/faxrcvd "recvq/fax00010.tif" "ttyI0" "00000018" "T.30 T2 timeout, expected page not received" "CALLER NUMBER: 18" "CALLER NUMBER: 18"
May 16 15:59:52.19: [26460]: RECV FAX: end
May 16 15:59:52.19: [26460]: SESSION END


Boris Halter

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null