![]() |
Hello, i have some problems using Hylafax 4.1.2 with my Sedlbauer speedfax pci ISDN-Card. The speedfax pci is a semi-active ISDN-CArd which acts as a Class 1 Modem. Receiving one Fax page wether in fine or in normal resolution works fine but multipage faxes will abort after the first page. Has anyone any idea ? Thanks for help, Detlev. Here are some cuts from the syslog ****************Fax-Init May 8 10:56:52 comsurv FaxQueuer[13745]: MODEM ttyI1: NUMBER xxx May 8 10:56:52 comsurv FaxGetty[13758]: OPEN /dev/ttyI1 HylaFAX (tm) Version 4 .1.2 May 8 10:56:52 comsurv FaxGetty[13758]: MODEM set DTR OFF May 8 10:56:52 comsurv FaxGetty[13758]: DELAY 75 ms May 8 10:56:52 comsurv FaxGetty[13758]: MODEM set DTR ON May 8 10:56:52 comsurv FaxGetty[13758]: DELAY 2600 ms May 8 10:56:55 comsurv FaxGetty[13758]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF May 8 10:56:55 comsurv FaxGetty[13758]: MODEM flush i/o May 8 10:56:55 comsurv FaxGetty[13758]: <-- [4:ATZ\r] May 8 10:56:55 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:55 comsurv FaxGetty[13758]: DELAY 3000 ms May 8 10:56:58 comsurv FaxGetty[13758]: <-- [7:at&e71\r] May 8 10:56:58 comsurv FaxGetty[13758]: --> [6:at&e71] May 8 10:56:58 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:58 comsurv FaxGetty[13758]: <-- [5:ATE0\r] May 8 10:56:58 comsurv FaxGetty[13758]: --> [4:ATE0] May 8 10:56:58 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:58 comsurv FaxGetty[13758]: <-- [5:ATV1\r] May 8 10:56:58 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:58 comsurv FaxGetty[13758]: <-- [5:ATQ0\r] May 8 10:56:58 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:58 comsurv FaxGetty[13758]: <-- [7:ATS0=0\r] May 8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:59 comsurv FaxGetty[13758]: <-- [7:ATS8=2\r] May 8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:59 comsurv FaxGetty[13758]: <-- [8:ATS7=60\r] May 8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:59 comsurv FaxGetty[13758]: <-- [12:AT+FCLASS=?\r] May 8 10:56:59 comsurv FaxGetty[13758]: --> [5:0,1,8] May 8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports "Data" May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports "Class 1" May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports "Voice" May 8 10:56:59 comsurv FaxGetty[13758]: <-- [12:AT+FCLASS=1\r] May 8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:59 comsurv FaxGetty[13758]: <-- [5:ATI3\r] May 8 10:56:59 comsurv FaxGetty[13758]: --> [10:Linux ISDN] May 8 10:56:59 comsurv FaxGetty[13758]: --> [1:0] May 8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:59 comsurv FaxGetty[13758]: MODEM: Mfr Linux ISDN 0 May 8 10:56:59 comsurv FaxGetty[13758]: <-- [5:ATI0\r] May 8 10:56:59 comsurv FaxGetty[13758]: --> [10:Linux ISDN] May 8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:59 comsurv FaxGetty[13758]: MODEM: Model Linux ISDN May 8 10:56:59 comsurv FaxGetty[13758]: <-- [9:AT+FTM=?\r] May 8 10:56:59 comsurv FaxGetty[13758]: --> [13:3,24,48,72,96] May 8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 3.85 line/mm May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 7.7 line/mm May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 2400 bit/s May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 4800 bit/s May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 7200 bit/s May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 9600 bit/s May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports page width 1728 pixels i n 215 mm May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports page width 2048 pixels i n 255 mm May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports page width 2432 pixels i n 303 mm May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports A4 page length (297 mm) May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports B4 page length (364 mm) May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports unlimited page length May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 1-D MR May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 2-D MR May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 0 ms/scanline May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 5 ms/scanline May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 10 ms, 5 ms/scanline May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 10 ms/scanline May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 20 ms, 10 ms/scanline May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 20 ms/scanline May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 40 ms, 20 ms/scanline May 8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 40 ms/scanline May 8 10:56:59 comsurv FaxGetty[13758]: <-- [9:AT+FRM=?\r] May 8 10:56:59 comsurv FaxGetty[13758]: --> [13:3,24,48,72,96] May 8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:56:59 comsurv FaxGetty[13758]: <-- [12:AT+FCLASS=1\r] May 8 10:57:00 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:57:00 comsurv FaxGetty[13758]: MODEM LINUX ISDN 0 Linux ISDN/ May 8 10:57:00 comsurv FaxGetty[13758]: <-- [5:ATM0\r] May 8 10:57:00 comsurv FaxGetty[13758]: --> [2:OK] May 8 10:57:00 comsurv FaxGetty[13758]: STATE CHANGE: BASE -> RUNNING May 8 10:57:00 comsurv FaxGetty[13758]: MODEM input buffering disabled May 8 10:57:00 comsurv FaxQueuer[13745]: MODEM ttyI1: READY, capabilities P3fc3 e73f:ff *************** receiving page fax, normal resolutuio May 8 11:26:52 comsurv FaxGetty[13908]: --> [17:CALLER NUMBER: 26] May 8 11:26:52 comsurv FaxGetty[13908]: --> [4:RING] May 8 11:26:52 comsurv FaxGetty[13908]: ANSWER: CID NUMBER "CALLER NUMBER: 26" NAME "CALLER NUMBER: 26" May 8 11:26:52 comsurv FaxGetty[13908]: STATE CHANGE: LISTENING -> ANSWERING May 8 11:26:52 comsurv FaxGetty[13908]: MODEM input buffering enabled May 8 11:26:52 comsurv FaxQueuer[13745]: MODEM ttyI1: COMID 00000009 May 8 11:26:57 comsurv FaxGetty[13908]: ANSWER: FAX CONNECTION DEVICE '/dev/tt yI1' May 8 11:27:02 comsurv FaxGetty[13908]: ACCEPT TSI "+49 2534 xxxx" May 8 11:27:57 comsurv FaxGetty[13908]: RECV FAX (00000009): from +49 2534 xxxxx 2, page 1 in 0:55, INF, 3.85 line/mm, 1-D MR, 9600 bit/s May 8 11:28:00 comsurv FaxGetty[13908]: RECV FAX (00000009): recvq/fax00006.tif from +49 2534 xxxxx, route to <unspecified>, 1 pages in 1:03 May 8 11:28:02 comsurv FaxGetty[13908]: RECV FAX (00000009): session with +49 2 534 xxxxx terminated abnormally: T.30 T2 timeout, expected page not received May 8 11:28:02 comsurv FaxGetty[13908]: RECV FAX: bin/faxrcvd "recvq/fax00006.t if" "ttyI1" "00000009" "T.30 T2 timeout, expected page not received" "CALLER NUM BER: 26" "CALLER NUMBER: 26" May 8 11:28:02 comsurv FaxQueuer[13745]: MODEM ttyI1: COMID May 8 11:28:02 comsurv FaxGetty[13908]: <-- [5:ATH0\r] May 8 11:28:02 comsurv scanmails[13936]: execution started May 8 11:28:02 comsurv FaxGetty[13908]: --> [10:NO CARRIER] May 8 11:28:02 comsurv FaxGetty[13908]: MODEM No carrier May 8 11:28:02 comsurv FaxGetty[13908]: MODEM set DTR OFF May 8 11:28:02 comsurv FaxGetty[13908]: MODEM set DTR OFF May 8 11:28:02 comsurv FaxGetty[13908]: DELAY 75 ms May 8 11:28:02 comsurv FaxGetty[13908]: MODEM set DTR ON May 8 11:28:02 comsurv FaxGetty[13908]: DELAY 2600 ms May 8 11:28:03 comsurv scanmails[14053]: terminating May 8 11:28:05 comsurv FaxGetty[13908]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF May 8 11:28:05 comsurv FaxGetty[13908]: MODEM flush i/o May 8 11:28:05 comsurv FaxGetty[13908]: <-- [4:ATZ\r] ..... and the ../hylafax/log-file May 08 11:26:52.15: [13908]: SESSION BEGIN 00000009 492534xxxxxx May 08 11:26:52.15: [13908]: HylaFAX (tm) Version 4.1.2 May 08 11:26:52.15: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output dis abled May 08 11:26:52.15: [13908]: <-- [4:ATA\r] May 08 11:26:57.29: [13908]: --> [7:CONNECT] May 08 11:26:57.29: [13908]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyI1' May 08 11:26:57.29: [13908]: STATE CHANGE: ANSWERING -> RECEIVING May 08 11:26:57.29: [13908]: MODEM input buffering enabled May 08 11:26:57.29: [13908]: RECV FAX: begin May 08 11:26:57.29: [13908]: MODEM input buffering disabled May 08 11:26:57.29: [13908]: <-- HDLC<23:FF C0 02 0E B6 86 D6 76 F6 42 04 04 04 04 04 04 04 04 04 04 04 04 04> May 08 11:26:57.29: [13908]: <-- data [23] May 08 11:26:57.29: [13908]: <-- data [2] May 08 11:26:57.33: [13908]: --> [7:CONNECT] May 08 11:26:57.33: [13908]: <-- HDLC<10:FF C8 01 00 73 5F 01 79 03 C0> May 08 11:26:57.33: [13908]: <-- data [10] May 08 11:26:57.33: [13908]: <-- data [2] May 08 11:26:58.45: [13908]: --> [2:OK] May 08 11:26:58.45: [13908]: <-- [9:AT+FRH=3\r] May 08 11:26:58.72: [13908]: --> [7:CONNECT] May 08 11:27:00.36: [13908]: --> HDLC<25:FF C0 C2 4C EC 4C AC 6C 04 2C CC AC 4C 04 9C 2C D4 04 04 04 04 04 04 FA C4> May 08 11:27:00.36: [13908]: --> [2:OK] May 08 11:27:00.36: [13908]: REMOTE TSI "+49 2534 xxxxx" May 08 11:27:00.36: [13908]: <-- [9:AT+FRH=3\r] May 08 11:27:00.37: [13908]: --> [7:CONNECT] May 08 11:27:00.68: [13908]: --> HDLC<11:FF C8 C1 00 60 15 01 01 00 0A 70> May 08 11:27:00.68: [13908]: --> [2:OK] May 08 11:27:00.68: [13908]: REMOTE wants 9600 bit/s May 08 11:27:00.68: [13908]: REMOTE wants page width 1728 pixels in 215 mm May 08 11:27:00.68: [13908]: REMOTE wants unlimited page length May 08 11:27:00.68: [13908]: REMOTE wants 3.85 line/mm May 08 11:27:00.68: [13908]: REMOTE wants 1-D MR May 08 11:27:00.68: [13908]: RECV training at v.29 9600 bit/s May 08 11:27:00.68: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output gen erated May 08 11:27:00.68: [13908]: <-- [10:AT+FRM=96\r] May 08 11:27:01.04: [13908]: --> [7:CONNECT] May 08 11:27:02.63: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis abled May 08 11:27:02.63: [13908]: RECV: TCF 1915 bytes, 5% non-zero, 1809 zero-run May 08 11:27:02.63: [13908]: --> [10:NO CARRIER] May 08 11:27:02.63: [13908]: DELAY 75 ms May 08 11:27:02.71: [13908]: TRAINING succeeded May 08 11:27:02.71: [13908]: ACCEPT TSI "+49 2534 xxxxx" May 08 11:27:02.71: [13908]: <-- [9:AT+FTH=3\r] May 08 11:27:04.34: [13908]: --> [7:CONNECT] May 08 11:27:04.34: [13908]: <-- HDLC<3:FF C8 21> May 08 11:27:04.34: [13908]: <-- data [3] May 08 11:27:04.34: [13908]: <-- data [2] May 08 11:27:04.60: [13908]: --> [2:OK] May 08 11:27:04.60: [13908]: MODEM input buffering enabled May 08 11:27:04.60: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output gen erated May 08 11:27:04.60: [13908]: <-- [10:AT+FRM=96\r] May 08 11:27:05.19: [13908]: --> [7:CONNECT] May 08 11:27:05.19: [13908]: RECV: begin page May 08 11:27:55.94: [13908]: RECV: 1149 total lines, 0 bad lines, 0 consecutive bad lines May 08 11:27:55.94: [13908]: RECV: end page May 08 11:27:55.94: [13908]: --> [10:NO CARRIER] May 08 11:27:55.94: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis abled May 08 11:27:55.94: [13908]: MODEM input buffering disabled May 08 11:27:55.94: [13908]: <-- [9:AT+FRH=3\r] May 08 11:27:55.98: [13908]: --> [7:CONNECT] May 08 11:27:57.05: [13908]: --> HDLC<5:FF C8 F2 AC A0> May 08 11:27:57.05: [13908]: --> [2:OK] May 08 11:27:57.05: [13908]: RECV recv MPS (more pages, same document) May 08 11:27:57.05: [13908]: DELAY 75 ms May 08 11:27:57.13: [13908]: <-- [9:AT+FTH=3\r] May 08 11:27:57.13: [13908]: --> [10:NO CARRIER] May 08 11:27:57.13: [13908]: RECV send MCF (message confirmation) May 08 11:27:57.13: [13908]: RECV FAX (00000009): from +49 2534 xxxxx, page 1 in 0:55, INF, 3.85 line/mm, 1-D MR, 9600 bit/s May 08 11:27:57.13: [13908]: MODEM input buffering enabled May 08 11:27:57.13: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output gen erated May 08 11:27:57.13: [13908]: <-- [10:AT+FRM=96\r] May 08 11:28:00.75: [13908]: --> [7:FCERROR] May 08 11:28:00.75: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis abled May 08 11:28:00.75: [13908]: MODEM input buffering disabled May 08 11:28:00.75: [13908]: RECV FAX (00000009): recvq/fax00006.tif from +49 25 34 xxxxx, route to <unspecified>, 1 pages in 1:03 May 08 11:28:00.75: [13908]: RECV FAX: T.30 T2 timeout, expected page not receiv ed May 08 11:28:00.75: [13908]: <-- [9:AT+FTH=3\r] May 08 11:28:02.38: [13908]: --> [7:CONNECT] May 08 11:28:02.38: [13908]: <-- HDLC<3:FF C8 5F> May 08 11:28:02.38: [13908]: <-- data [3] May 08 11:28:02.38: [13908]: <-- data [2] May 08 11:28:02.64: [13908]: --> [2:OK] May 08 11:28:02.64: [13908]: MODEM input buffering enabled May 08 11:28:02.64: [13908]: RECV FAX (00000009): session with +49 2534 xxxxx te rminated abnormally: T.30 T2 timeout, expected page not received May 08 11:28:02.64: [13908]: RECV FAX: bin/faxrcvd "recvq/fax00006.tif" "ttyI1" "00000009" "T.30 T2 timeout, expected page not received" "CALLER NUMBER: 26" "CA LLER NUMBER: 26" May 08 11:28:02.71: [13908]: RECV FAX: end May 08 11:28:02.71: [13908]: SESSION END ************ the same with fine resolution May 8 11:31:52 comsurv FaxGetty[13908]: --> [17:CALLER NUMBER: 26] May 8 11:31:52 comsurv FaxGetty[13908]: --> [4:RING] May 8 11:31:52 comsurv FaxGetty[13908]: ANSWER: CID NUMBER "CALLER NUMBER: 26" NAME "CALLER NUMBER: 26" May 8 11:31:52 comsurv FaxGetty[13908]: STATE CHANGE: LISTENING -> ANSWERING May 8 11:31:52 comsurv FaxGetty[13908]: MODEM input buffering enabled May 8 11:31:52 comsurv FaxQueuer[13745]: MODEM ttyI1: COMID 00000010 May 8 11:31:57 comsurv FaxGetty[13908]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyI1' May 8 11:32:03 comsurv FaxGetty[13908]: ACCEPT TSI "+49 2534 xxxxx" May 8 11:33:21 comsurv FaxGetty[13908]: RECV FAX (00000010): from +49 2534 xxxxx, page 1 in 1:18, INF, 7.7 line/mm, 1-D MR, 9600 bit/s May 8 11:33:25 comsurv FaxGetty[13908]: RECV FAX (00000010): recvq/fax00007.tif from +49 2534 xxxxx, route to <unspecified>, 1 pages in 1:28 May 8 11:33:26 comsurv FaxGetty[13908]: RECV FAX (00000010): session with +49 2534 xxxxx terminated abnormally: T.30 T2 timeout, expected page not received May 8 11:33:26 comsurv FaxGetty[13908]: RECV FAX: bin/faxrcvd "recvq/fax00007.tif" "ttyI1" "00000010" "T.30 T2 timeout, expected page not received" "CALLER NUMBER: 26" "CALLER NUMBER: 26" May 8 11:33:27 comsurv FaxQueuer[13745]: MODEM ttyI1: COMID May 8 11:33:27 comsurv FaxGetty[13908]: <-- [5:ATH0\r] May 8 11:33:27 comsurv scanmails[14081]: execution started May 8 11:33:27 comsurv FaxGetty[13908]: --> [10:NO CARRIER] May 8 11:33:27 comsurv FaxGetty[13908]: MODEM No carrier May 8 11:33:27 comsurv FaxGetty[13908]: MODEM set DTR OFF May 8 11:33:27 comsurv FaxGetty[13908]: MODEM set DTR OFF May 8 11:33:27 comsurv FaxGetty[13908]: DELAY 75 ms May 8 11:33:27 comsurv FaxGetty[13908]: MODEM set DTR ON May 8 11:33:27 comsurv FaxGetty[13908]: DELAY 2600 ms May 8 11:33:27 comsurv scanmails[14198]: terminating May 8 11:33:29 comsurv FaxGetty[13908]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF May 8 11:33:29 comsurv FaxGetty[13908]: MODEM flush i/o May 8 11:33:29 comsurv FaxGetty[13908]: <-- [4:ATZ\r] .... ************* and the ../hylafax/log.. May 08 11:31:52.83: [13908]: SESSION BEGIN 00000010 492534xxxxx May 08 11:31:52.83: [13908]: HylaFAX (tm) Version 4.1.2 May 08 11:31:52.83: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output dis abled May 08 11:31:52.83: [13908]: <-- [4:ATA\r] May 08 11:31:57.95: [13908]: --> [7:CONNECT] May 08 11:31:57.96: [13908]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyI1' May 08 11:31:57.96: [13908]: STATE CHANGE: ANSWERING -> RECEIVING May 08 11:31:57.96: [13908]: MODEM input buffering enabled May 08 11:31:57.96: [13908]: RECV FAX: begin May 08 11:31:57.96: [13908]: MODEM input buffering disabled May 08 11:31:57.96: [13908]: <-- HDLC<23:FF C0 02 0E B6 86 D6 76 F6 42 04 04 04 04 04 04 04 04 04 04 04 04 04> May 08 11:31:57.96: [13908]: <-- data [23] May 08 11:31:57.96: [13908]: <-- data [2] May 08 11:31:57.99: [13908]: --> [7:CONNECT] May 08 11:31:57.99: [13908]: <-- HDLC<10:FF C8 01 00 73 5F 01 79 03 C0> May 08 11:31:57.99: [13908]: <-- data [10] May 08 11:31:57.99: [13908]: <-- data [2] May 08 11:31:59.09: [13908]: --> [2:OK] May 08 11:31:59.09: [13908]: <-- [9:AT+FRH=3\r] May 08 11:31:59.37: [13908]: --> [7:CONNECT] May 08 11:32:01.00: [13908]: --> HDLC<25:FF C0 C2 4C EC 4C AC 6C 04 2C CC AC 4C 04 9C 2C D4 04 04 04 04 04 04 FA C4> May 08 11:32:01.00: [13908]: --> [2:OK] May 08 11:32:01.00: [13908]: REMOTE TSI "+49 2534 xxxxx" May 08 11:32:01.00: [13908]: <-- [9:AT+FRH=3\r] May 08 11:32:01.01: [13908]: --> [7:CONNECT] May 08 11:32:01.32: [13908]: --> HDLC<11:FF C8 C1 00 62 15 01 01 00 4E F3> May 08 11:32:01.32: [13908]: --> [2:OK] May 08 11:32:01.32: [13908]: REMOTE wants 9600 bit/s May 08 11:32:01.32: [13908]: REMOTE wants page width 1728 pixels in 215 mm May 08 11:32:01.32: [13908]: REMOTE wants unlimited page length May 08 11:32:01.32: [13908]: REMOTE wants 7.7 line/mm May 08 11:32:01.32: [13908]: REMOTE wants 1-D MR May 08 11:32:01.32: [13908]: RECV training at v.29 9600 bit/s May 08 11:32:01.32: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output gen erated May 08 11:32:01.32: [13908]: <-- [10:AT+FRM=96\r] May 08 11:32:01.68: [13908]: --> [7:CONNECT] May 08 11:32:03.28: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis abled May 08 11:32:03.28: [13908]: RECV: TCF 1915 bytes, 5% non-zero, 1808 zero-run May 08 11:32:03.28: [13908]: --> [10:NO CARRIER] May 08 11:32:03.28: [13908]: DELAY 75 ms May 08 11:32:03.36: [13908]: TRAINING succeeded May 08 11:32:03.36: [13908]: ACCEPT TSI "+49 2534 xxxxx" May 08 11:32:03.37: [13908]: <-- [9:AT+FTH=3\r] May 08 11:32:04.99: [13908]: --> [7:CONNECT] May 08 11:32:04.99: [13908]: <-- HDLC<3:FF C8 21> May 08 11:32:04.99: [13908]: <-- data [3] May 08 11:32:04.99: [13908]: <-- data [2] May 08 11:32:05.25: [13908]: --> [2:OK] May 08 11:32:05.25: [13908]: MODEM input buffering enabled May 08 11:32:05.25: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output gen erated May 08 11:32:05.25: [13908]: <-- [10:AT+FRM=96\r] May 08 11:32:05.85: [13908]: --> [7:CONNECT] May 08 11:32:05.85: [13908]: RECV: begin page May 08 11:33:20.22: [13908]: RECV: 2312 total lines, 0 bad lines, 0 consecutive bad lines May 08 11:33:20.22: [13908]: RECV: end page May 08 11:33:20.22: [13908]: --> [10:NO CARRIER] May 08 11:33:20.22: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis abled May 08 11:33:20.22: [13908]: MODEM input buffering disabled May 08 11:33:20.22: [13908]: <-- [9:AT+FRH=3\r] May 08 11:33:20.36: [13908]: --> [7:CONNECT] May 08 11:33:21.40: [13908]: --> HDLC<5:FF C8 F2 AC A0> May 08 11:33:21.40: [13908]: --> [2:OK] May 08 11:33:21.40: [13908]: RECV recv MPS (more pages, same document) May 08 11:33:21.40: [13908]: DELAY 75 ms May 08 11:33:21.48: [13908]: <-- [9:AT+FTH=3\r] May 08 11:33:21.48: [13908]: --> [10:NO CARRIER] May 08 11:33:21.48: [13908]: RECV send MCF (message confirmation) May 08 11:33:21.48: [13908]: RECV FAX (00000010): from +49 2534 xxxxx, page 1 in 1:18, INF, 7.7 line/mm, 1-D MR, 9600 bit/s May 08 11:33:21.48: [13908]: MODEM input buffering enabled May 08 11:33:21.48: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output gen erated May 08 11:33:21.48: [13908]: <-- [10:AT+FRM=96\r] May 08 11:33:25.07: [13908]: --> [7:FCERROR] May 08 11:33:25.07: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis abled May 08 11:33:25.07: [13908]: MODEM input buffering disabled May 08 11:33:25.07: [13908]: RECV FAX (00000010): recvq/fax00007.tif from +49 25 34 xxxxx, route to <unspecified>, 1 pages in 1:28 May 08 11:33:25.07: [13908]: RECV FAX: T.30 T2 timeout, expected page not receiv ed May 08 11:33:25.07: [13908]: <-- [9:AT+FTH=3\r] May 08 11:33:26.70: [13908]: --> [7:CONNECT] May 08 11:33:26.70: [13908]: <-- HDLC<3:FF C8 5F> May 08 11:33:26.70: [13908]: <-- data [3] May 08 11:33:26.70: [13908]: <-- data [2] May 08 11:33:26.96: [13908]: --> [2:OK] May 08 11:33:26.96: [13908]: MODEM input buffering enabled May 08 11:33:26.96: [13908]: RECV FAX (00000010): session with +49 2534 xxxxx te rminated abnormally: T.30 T2 timeout, expected page not received May 08 11:33:26.96: [13908]: RECV FAX: bin/faxrcvd "recvq/fax00007.tif" "ttyI1" "00000010" "T.30 T2 timeout, expected page not received" "CALLER NUMBER: 26" "CA LLER NUMBER: 26" May 08 11:33:27.03: [13908]: RECV FAX: end May 08 11:33:27.03: [13908]: SESSION END ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null