[hylafax-users] Hylafax and USRobotics Modem PROBLEMM

[Carsten Dirk <carsten.dirk@gmx.de>]

rear, do not have yesterday with me hylafax
instaliert it left well up to einz I can faxes
send without Problemme however emfangen can I it
I war each times no fax and following email: The
whole is instaliert under Woody Debian. Have US a
Robotics Sportster Flash modem What can lie!

---
An attempt to receive facsimile on ttyS0 failed because:

RSPREC invalid response received

---- Transcript of session follows ----

Apr 28 20:07:16.95: [ 1952]: SESSION BEGIN 00000026 4988989800
Apr 28 20:07:16.95: [ 1952]: HylaFAX (tm) Version 4.1.1
Apr 28 20:07:16.95: [ 1952]: <-- [4:ATA�]
Apr 28 20:07:23.16: [ 1952]: --> [4:+FCO]
Apr 28 20:07:23.16: [ 1952]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Apr 28 20:07:23.16: [ 1952]: MODEM input buffering enabled
Apr 28 20:07:23.16: [ 1952]: RECV FAX: begin
Apr 28 20:07:25.01: [ 1952]: --> [27:+FTI:"+49 2561 959-282697 "]
Apr 28 20:07:25.01: [ 1952]: REMOTE TSI "+49 2561 959-282697"
Apr 28 20:07:25.01: [ 1952]: --> [20:+FCS:1,3,0,0,0,0,0,0]
Apr 28 20:07:25.01: [ 1952]: REMOTE wants 9600 bit/s
Apr 28 20:07:25.01: [ 1952]: REMOTE wants page width 1728 pixels in 215 mm
Apr 28 20:07:25.01: [ 1952]: REMOTE wants A4 page length (297 mm)
Apr 28 20:07:25.01: [ 1952]: REMOTE wants 7.7 line/mm
Apr 28 20:07:25.01: [ 1952]: REMOTE wants 1-D MR
Apr 28 20:07:25.01: [ 1952]: --> [2:OK]
Apr 28 20:07:25.01: [ 1952]: <-- [7:AT+FDR�]
Apr 28 20:07:30.25: [ 1952]: --> [27:+FTI:"+49 2561 959-282697 "]
Apr 28 20:07:30.25: [ 1952]: REMOTE TSI "+49 2561 959-282697"
Apr 28 20:07:30.25: [ 1952]: --> [20:+FCS:1,2,0,0,0,0,0,0]
Apr 28 20:07:30.25: [ 1952]: REMOTE wants 7200 bit/s
Apr 28 20:07:30.25: [ 1952]: REMOTE wants page width 1728 pixels in 215 mm
Apr 28 20:07:30.25: [ 1952]: REMOTE wants A4 page length (297 mm)
Apr 28 20:07:30.25: [ 1952]: REMOTE wants 7.7 line/mm
Apr 28 20:07:30.25: [ 1952]: REMOTE wants 1-D MR
Apr 28 20:07:34.02: [ 1952]: --> [7:CONNECT]
Apr 28 20:07:34.02: [ 1952]: RECV: begin page
Apr 28 20:07:34.02: [ 1952]: RECV: send trigger 022
Apr 28 20:07:36.61: [ 1952]: RECV: 170 total lines, 5 bad lines, 4
consecutive bad lines
Apr 28 20:07:36.61: [ 1952]: --> [16:+FPS:1,171,0,0,0]
Apr 28 20:07:45.95: [ 1952]: --> [7:+FHS:A1]
Apr 28 20:07:45.95: [ 1952]: REMOTE HANGUP: RSPREC invalid response received
(code A1)
Apr 28 20:07:46.08: [ 1952]: --> [2:OK]
Apr 28 20:07:46.08: [ 1952]: RECV FAX (00000026): recvq/fax00021.tif from
+49 2561 959-282697, route to <unspecified>, 0
pages in 0:23
Apr 28 20:07:46.08: [ 1952]: RECV FAX: RSPREC invalid response received
Apr 28 20:07:46.09: [ 1952]: RECV FAX (00000026): session with +49 2561
959-282697 terminated abnormally: RSPREC invalid
response received
Apr 28 20:07:46.09: [ 1952]: RECV FAX: bin/faxrcvd "recvq/fax00021.tif"
"ttyS0" "00000026" "RSPREC invalid response
received" "" ""
--------------------------

Config:

#
CountryCode: 49
AreaCode: 2001
FAXNumber: +49.2001.203.003
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 527
SessionTracing: 527
RecvFileMode: 0644
LogFileMode: 0777
DeviceMode: 0666
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-r -b -s %s %l"
LocalIdentifier: "cobra"
LogFacility: daemon
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 30
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use class 2.0 interface
ModemRate: 38400 # DCE-DTE communication rate
ModemFlowControl: rtscts # XON/XOFF flow control assumed
#
ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
#
ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
ModemResultCodesCmd: ATQ0X4 # enable extended result codes
#
# NB: adaptive answer only seems to work properly when
# the modem is left idling in Class 2.0
#
ModemSetupAACmd: AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd: AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
# response so that the server will do copy quality checking.
#
Class2CQQueryCmd: !(0),(0) # override modem response
#
# Disables the reporting of bad frames by the modem. This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd: AT+FNR=1,1,1,0
#
# USR modems violate Class 2.0 specs and do not send RTC itself
#
Class2SendRTC: yes
#
# +FAP=? not supported on this modem, gives ERROR in ServerTracing
#
Class2APQueryCmd: none
 
 
28  Apr,  2002  21:16:00
--  Mit  freundlichen  Gr�ssen  Carsten Dirk
mailto:carsten.dirk@gmx.de


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null