[hylafax-users] Fax Reception Problem with Multitech ISI3334/8

["Sedat Yilmazer" <sedat@kibele.com>]

I have set up a faxserver with

I have hylafax-4.1-0.11mdk running on Mandrake 8.0
with multitech 8 line ISA multitech modem (ISI3334/8) xonxoff flowcontrol
selected
No special pach installed.

At some point during page reception Hylafax decides that the page is
received and goes into command mode and gets lots of garbage ( appearently
rest of the page) and after some time comes up with the page data as show
below.  Page is partialy received ( up to the point where hylafax decides
for the end - of - page)

 How can I solve this problem. What other info is required for the solution
of such problems

sessiob tracing

-------------------------------------------

--------------------------------------------------------- session
trace -------------
Jan 07 14:323.26: [25231]: SESSION BEGIN 00001381 902122523978
Jan 07 14:32:03.26: [25231]: <-- [4:ATA\r]
Jan 07 14:32:27.60: [25231]: --> [5:+FCON]
Jan 07 14:32:27.60: [25231]: ANSWER: FAX CONNECTION
Jan 07 14:32:27.60: [25231]: MODEM input buffering enabled
Jan 07 14:32:27.60: [25231]: RECV FAX: begin
Jan 07 14:32:31.62: [25231]: --> [28:+FTSI:"         02123213194"]
Jan 07 14:32:31.62: [25231]: REMOTE TSI "02123213194"
Jan 07 14:32:31.62: [25231]: --> [21:+FDCS:0,3,0,2,0,0,0,3]
Jan 07 14:32:31.62: [25231]: REMOTE wants 9600 bit/s
Jan 07 14:32:31.62: [25231]: REMOTE wants page width 1728 pixels in 215 mm
Jan 07 14:32:31.62: [25231]: REMOTE wants unlimited page length
Jan 07 14:32:31.62: [25231]: REMOTE wants 3.85 line/mm
Jan 07 14:32:31.62: [25231]: REMOTE wants 1-D MR
Jan 07 14:32:31.62: [25231]: --> [2:OK]
Jan 07 14:32:31.62: [25231]: <-- [7:AT+FDR\r]
Jan 07 14:32:33.18: [25231]: --> [5:+FCFR]
Jan 07 14:32:33.18: [25231]: --> [28:+FTSI:"         02123213194"]
Jan 07 14:32:33.18: [25231]: REMOTE TSI "02123213194"
Jan 07 14:32:33.18: [25231]: --> [21:+FDCS:0,3,0,2,0,0,0,3]
Jan 07 14:32:33.18: [25231]: REMOTE wants 9600 bit/s
Jan 07 14:32:33.18: [25231]: REMOTE wants page width 1728 pixels in 215 mm
Jan 07 14:32:33.18: [25231]: REMOTE wants unlimited page length
Jan 07 14:32:33.18: [25231]: REMOTE wants 3.85 line/mm
Jan 07 14:32:33.18: [25231]: REMOTE wants 1-D MR
Jan 07 14:32:34.17: [25231]: --> [7:CONNECT]
Jan 07 14:32:34.17: [25231]: RECV: begin page
Jan 07 14:32:34.17: [25231]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Jan 07 14:32:34.17: [25231]: RECV: send trigger 022
Jan 07 14:32:34.17: [25231]: <-- data [1]
Jan 07 14:32:45.60: [25231]: RECV: 13090 bytes of data, 580 total lines
Jan 07 14:32:45.60: [25231]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Jan 07 14:32:45.60: [25231]: --> [17:+FPTS:1,580,0,0,0]
Jan 07 14:32:46.86: [25231]: --> [6:+FET:0]
Jan 07 14:32:46.86: [25231]: RECV recv MPS (more pages, same document)
Jan 07 14:32:46.86: [25231]: --> [2:OK]
Jan 07 14:32:46.86: [25231]: RECV send MCF (message confirmation)
Jan 07 14:32:46.86: [25231]: RECV FAX (00001381): from 02123213194, page 1
in 0:15, INF, 3.85 line/mm, 1-D MR, 9600 bit/s

Jan 07 14:32:46.86: [25231]: <-- [7:AT+FDR\r]
Jan 07 14:32:49.62: [25231]: --> [7:CONNECT]
Jan 07 14:32:49.62: [25231]: RECV: begin page
Jan 07 14:32:49.62: [25231]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Jan 07 14:32:49.62: [25231]: RECV: send trigger 022
Jan 07 14:32:49.62: [25231]: <-- data [1]
Jan 07 14:32:53.96: [25231]: RECV: 4665 bytes of data, 85 total lines
Jan 07 14:32:53.96: [25231]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled

----- > Problem starts here. hylafax thinks that 85 lines are
received --------------------<

Jan 07 14:32:54.21: [25231]: --> [362:1ØÀ611��l`?e`1ØM®-


 ...... Alotof junk is deleted here

--------> Modem comes up with the results and reports 1144 lines ( hylafax
got 85 lines )

'Ó      -L%?[D¸oN¸ėX²Y?]
Jan 07 14:33:49.87: [25231]: --> [18:+FPTS:1,1144,0,0,0]
Jan 07 14:33:51.14: [25231]: --> [6:+FET:0]
Jan 07 14:33:51.14: [25231]: RECV recv MPS (more pages, same document)
Jan 07 14:33:51.14: [25231]: --> [2:OK]
Jan 07 14:33:51.14: [25231]: RECV send MCF (message confirmation)
Jan 07 14:33:51.14: [25231]: RECV FAX (00001381): from 02123213194, page 2
in 1:05, INF, 3.85 line/mm, 1-D MR, 9600 bit/s

Jan 07 14:33:51.14: [25231]: <-- [7:AT+FDR\r]
Jan 07 14:34:09.26: [25231]: --> [7:+FHNG:2]
Jan 07 14:34:09.26: [25231]: REMOTE HANGUP: Call aborted,  from +FK or <CAN>
(code 2)
Jan 07 14:34:09.26: [25231]: RECV FAX (00001381): recvq/fax01083.tif from
02123213194, route to <unspecified>, 2 pages in 1:42

Jan 07 14:34:09.26: [25231]: RECV FAX: Call aborted,  from +FK or <CAN>
Jan 07 14:34:09.26: [25231]: RECV FAX (00001381): session with 02123213194
terminated abnormally: Call aborted,  from +FK or <CAN>

Jan 07 14:34:09.26: [25231]: RECV FAX: bin/faxrcvd "recvq/fax01083.tif"
"ttyM1c" "00001381" "Call aborted,  from +FK or <CAN>"

Jan 07 14:34:09.71: [25231]: RECV FAX: end
Jan 07 14:34:09.71: [25231]: SESSION END

---------------------- end of session tracing ---
Sedat YILMAZER




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null