Re: [hylafax-users] PABX and "0"

["Josh Welch" <jwelch@buffalowildwings.com>]

Add a 0 to the ModemDialCmd in your config.

----- Original Message -----
From: "alain siani" <ASiani@wanadoo.fr>
To: <hylafax-users@hylafax.org>
Sent: Friday, November 02, 2001 10:01 AM
Subject: [hylafax-users] PABX and "0"


> In this config file, i would like to say to my modem to compose "0" before
my
> phone number because i have a PABX, how can i do ?
>
> Thanks a lot !
> Alain
>
>
> # $Id: usr-2.0,v 1.6 2001/06/04 05:09:46 darren Exp $
> #
> # HylaFAX Facsimile Software
> #
> # Copyright (c) 1990-1996 Sam Leffler
> # Copyright (c) 1991-1996 Silicon Graphics, Inc.
> # HylaFAX is a trademark of Silicon Graphics, Inc.
> #
> # Permission to use, copy, modify, distribute, and sell this software and
> # its documentation for any purpose is hereby granted without fee,
provided
> # that (i) the above copyright notices and this permission notice appear
in
> # all copies of the software and related documentation, and (ii) the names
of
> # Sam Leffler and Silicon Graphics may not be used in any advertising or
> # publicity relating to the software without the specific, prior written
> # permission of Sam Leffler and Silicon Graphics.
> #
> # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
> # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
> # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
> #
> # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
> # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
> # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
> # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY
OF
> # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
> # OF THIS SOFTWARE.
> #
>
> #
> # Configuration for using the Class 2.0 command interface
> # with a USR v.34 Courier or Sporster modem.
> #
> # RTS/CTS flow control is used default.
> #
> #
> CountryCode: 33
> AreaCode: 4
> FAXNumber: +33.4.91598950
> LongDistancePrefix: 00
> InternationalPrefix: 00
> DialStringRules: etc/dialrules.europe
> ServerTracing: 1
> SessionTracing: 11
> RecvFileMode: 0600
> LogFileMode: 0600
> DeviceMode: 0600
> RingsBeforeAnswer: 1
> SpeakerVolume: off
> GettyArgs: "-h %l dx_%s"
> LocalIdentifier: "NothingSetup"
> TagLineFont: etc/lutRS18.pcf
> TagLineFormat: "From %%l|%c|Page %%P of %%T"
> MaxRecvPages: 25
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType: Class2.0 # use class 2.0 interface
> ModemRate: 38400 # DCE-DTE communication rate
> ModemFlowControl: rtscts # XON/XOFF flow control assumed
> #
> ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control
> ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
> ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
> #
> ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
> ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
> ModemResultCodesCmd: ATQ0X4 # enable extended result codes
> #
> # NB: adaptive answer only seems to work properly when
> #     the modem is left idling in Class 2.0
> #
> ModemSetupAACmd: AT+FAA=1
> #
> # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
> # Note that we both turn the speaker on/off and set volume.
> #
> ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1"
> #
> # Modem does not support HDLC frame tracing; we add this just
> # to eliminate spurious ERROR results that confuse the naive.
> #
> Class2BUGCmd: AT+FBU=0
> #
> # The modem doesn't support copy quality checking, even though it
> # returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
> # response so that the server will do copy quality checking.
> #
> Class2CQQueryCmd: !(0),(0) # override modem response
> #
> # Disables the reporting of bad frames by the modem.  This
> # overcomes a firmware problem in the x2 and V90 Sportsters.
> # It is not necessary for the Courier modem.
> #
> Class2NRCmd:    AT+FNR=1,1,1,0
> #
> # USR modems violate Class 2.0 specs and do not send RTC itself
> #
> Class2SendRTC: yes
> #
> # +FAP=? not supported on this modem, gives ERROR in ServerTracing
> #
> Class2APQueryCmd:       none
>
> --
> --
> Alain
>
>
> ____________________ HylaFAX(tm) Users Mailing List
_______________________
>  To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org <
/dev/null
>



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null