 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
Re: [hylafax-users] zyxel u-1496e config
- To: "hylafax" <hylafax-users@hylafax.org>
- Subject: Re: [hylafax-users] zyxel u-1496e config
- From: "Dan" <dwright@spca.org>
- Date: Thu, 30 Aug 2001 15:13:50 -0500
-- >Here. Try this (attached). Send me the session logs from two consecutive >attempts. Lee thanks for the rpm. I installed rpm and sent some test faxes looks great sent about 6 faxes to different numbers all went, tried to fax you but it gave me a No carrier detected error. Here are the logs you asked for. thanks for the help :-) Dan Aug 30 10:01:07.97: [ 1084]: SESSION BEGIN 00000034 12149728694975 Aug 30 10:01:07.97: [ 1084]: HylaFAX (tm) Version 4.1 Aug 30 10:01:07.97: [ 1084]: SEND FAX: JOB 20 DEST xxx-xxx-xxxx COMMID 00000034 Aug 30 10:01:07.97: [ 1084]: DEVICE '/dev/ttyS0' Aug 30 10:01:07.97: [ 1084]: MODEM set DTR OFF Aug 30 10:01:07.97: [ 1084]: DELAY 75 ms Aug 30 10:01:08.05: [ 1084]: MODEM set DTR ON Aug 30 10:01:08.05: [ 1084]: DELAY 2600 ms Aug 30 10:01:10.65: [ 1084]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS Aug 30 10:01:10.65: [ 1084]: MODEM flush i/o Aug 30 10:01:10.65: [ 1084]: <-- [4:ATZ\r] Aug 30 10:01:10.86: [ 1084]: --> [2:OK] Aug 30 10:01:10.86: [ 1084]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r] Aug 30 10:01:10.88: [ 1084]: --> [21:AT&B1&N0&S0*F0S38.3=1] Aug 30 10:01:10.88: [ 1084]: --> [2:OK] Aug 30 10:01:10.88: [ 1084]: <-- [5:ATE0\r] Aug 30 10:01:10.89: [ 1084]: --> [4:ATE0] Aug 30 10:01:10.89: [ 1084]: --> [2:OK] Aug 30 10:01:10.89: [ 1084]: <-- [5:ATV1\r] Aug 30 10:01:10.90: [ 1084]: --> [2:OK] Aug 30 10:01:10.90: [ 1084]: <-- [5:ATQ0\r] Aug 30 10:01:10.91: [ 1084]: --> [2:OK] Aug 30 10:01:10.91: [ 1084]: <-- [7:ATS0=0\r] Aug 30 10:01:10.92: [ 1084]: --> [2:OK] Aug 30 10:01:10.92: [ 1084]: <-- [7:ATS8=2\r] Aug 30 10:01:10.93: [ 1084]: --> [2:OK] Aug 30 10:01:10.93: [ 1084]: <-- [8:ATS7=60\r] Aug 30 10:01:10.94: [ 1084]: --> [2:OK] Aug 30 10:01:10.94: [ 1084]: <-- [6:AT&H3\r] Aug 30 10:01:10.95: [ 1084]: --> [2:OK] Aug 30 10:01:10.95: [ 1084]: <-- [6:AT&D2\r] Aug 30 10:01:10.96: [ 1084]: --> [2:OK] Aug 30 10:01:10.96: [ 1084]: <-- [6:AT&C1\r] Aug 30 10:01:10.97: [ 1084]: --> [2:OK] Aug 30 10:01:10.97: [ 1084]: <-- [12:AT+FCLASS=1\r] Aug 30 10:01:11.09: [ 1084]: --> [2:OK] Aug 30 10:01:11.09: [ 1084]: <-- [9:AT+FAA=1\r] Aug 30 10:01:11.10: [ 1084]: --> [2:OK] Aug 30 10:01:11.10: [ 1084]: <-- [7:ATM1L1\r] Aug 30 10:01:11.11: [ 1084]: --> [2:OK] Aug 30 10:01:11.11: [ 1084]: STATE CHANGE: RUNNING -> SENDING Aug 30 10:01:11.11: [ 1084]: MODEM input buffering enabled Aug 30 10:01:11.11: [ 1084]: <-- [12:AT+FCLASS=1\r] Aug 30 10:01:11.34: [ 1084]: --> [2:OK] Aug 30 10:01:11.34: [ 1084]: DIAL 9728694975 Aug 30 10:01:11.34: [ 1084]: <-- [15:ATDT9728694975\r] Aug 30 10:01:32.45: [ 1084]: --> [7:CONNECT] Aug 30 10:01:32.45: [ 1084]: MODEM input buffering disabled Aug 30 10:01:34.42: [ 1084]: --> HDLC<38:FF C0 04 00 00 8C 00 77 1D 22 61 B0 BB 00 00 BB BB 00 00 BB BB BB BB BB 80 10 0C 20 08 20 90 B7 C4 09 00 00 2F 80> Aug 30 10:01:34.42: [ 1084]: --> [2:OK] Aug 30 10:01:34.42: [ 1084]: REMOTE NSF "00 00 31 00 EE B8 44 86 0D DD 00 00 DD DD 00 00 DD DD DD DD DD 01 08 30 04 10 04 09 ED 23 90 00 00 F4 01 FF" Aug 30 10:01:34.42: [ 1084]: NSF remote fax equipment: Sharp/Olivetti Aug 30 10:01:34.42: [ 1084]: NSF remote station ID: "YYYYY" Aug 30 10:01:34.42: [ 1084]: <-- [9:AT+FRH=3\r] Aug 30 10:01:34.44: [ 1084]: --> [7:CONNECT] Aug 30 10:01:35.12: [ 1084]: --> HDLC<23:FF C0 02 4C 6C 6C 9C 04 8C 6C AC 04 2C 8C 4C 04 04 04 04 04 04 04 04> Aug 30 10:01:35.12: [ 1084]: --> [2:OK] Aug 30 10:01:35.12: [ 1084]: REMOTE CSI "214 561 9662" Aug 30 10:01:35.12: [ 1084]: <-- [9:AT+FRH=3\r] Aug 30 10:01:35.14: [ 1084]: --> [7:CONNECT] Aug 30 10:01:35.39: [ 1084]: --> HDLC<7:FF C8 01 00 77 1D 22> Aug 30 10:01:35.39: [ 1084]: --> [2:OK] Aug 30 10:01:35.39: [ 1084]: REMOTE best rate 14400 bit/s Aug 30 10:01:35.39: [ 1084]: REMOTE max page width 1728 pixels in 215 mm Aug 30 10:01:35.39: [ 1084]: REMOTE max unlimited page length Aug 30 10:01:35.39: [ 1084]: REMOTE best vres 7.7 line/mm Aug 30 10:01:35.39: [ 1084]: REMOTE best format 2-D MMR Aug 30 10:01:35.39: [ 1084]: REMOTE supports T.30 Annex A, ECM Aug 30 10:01:35.39: [ 1084]: REMOTE best 20 ms, 10 ms/scanline Aug 30 10:01:35.39: [ 1084]: USE 14400 bit/s Aug 30 10:01:35.39: [ 1084]: USE 20 ms, 10 ms/scanline Aug 30 10:01:35.39: [ 1084]: SEND file "docq/doc21.ps;40" Aug 30 10:01:35.39: [ 1084]: USE page width 1728 pixels in 215 mm Aug 30 10:01:35.39: [ 1084]: USE unlimited page length Aug 30 10:01:35.39: [ 1084]: USE 3.85 line/mm Aug 30 10:01:35.39: [ 1084]: USE 2-D MR Aug 30 10:01:35.39: [ 1084]: SEND training at v.17 14400 bit/s Aug 30 10:01:35.39: [ 1084]: <-- [9:AT+FTH=3\r] Aug 30 10:01:35.41: [ 1084]: --> [7:CONNECT] Aug 30 10:01:35.41: [ 1084]: <-- HDLC<23:FF C0 C2 0E AE 2E A6 CA E6 76 96 16 2E F6 72 04 04 04 04 04 04 04 04> Aug 30 10:01:35.41: [ 1084]: <-- data [23] Aug 30 10:01:35.41: [ 1084]: <-- data [2] Aug 30 10:01:37.13: [ 1084]: --> [7:CONNECT] Aug 30 10:01:37.13: [ 1084]: <-- HDLC<6:FF C8 C1 00 45 10> Aug 30 10:01:37.13: [ 1084]: <-- data [6] Aug 30 10:01:37.13: [ 1084]: <-- data [2] Aug 30 10:01:37.46: [ 1084]: --> [2:OK] Aug 30 10:01:37.46: [ 1084]: DELAY 75 ms Aug 30 10:01:37.54: [ 1084]: <-- [11:AT+FTM=145\r] Aug 30 10:01:37.56: [ 1084]: --> [7:CONNECT] Aug 30 10:01:37.56: [ 1084]: <-- data [1024] Aug 30 10:01:37.56: [ 1084]: <-- data [1024] Aug 30 10:01:37.56: [ 1084]: <-- data [652] Aug 30 10:01:37.56: [ 1084]: <-- data [2] Aug 30 10:01:40.70: [ 1084]: --> [2:OK] Aug 30 10:01:40.70: [ 1084]: <-- [9:AT+FRH=3\r] Aug 30 10:01:40.90: [ 1084]: --> [7:CONNECT] Aug 30 10:01:41.92: [ 1084]: --> HDLC<3:FF C8 21> Aug 30 10:01:41.92: [ 1084]: --> [2:OK] Aug 30 10:01:41.92: [ 1084]: TRAINING succeeded Aug 30 10:01:41.92: [ 1084]: DELAY 75 ms Aug 30 10:01:42.00: [ 1084]: <-- [11:AT+FTM=146\r] Aug 30 10:01:42.02: [ 1084]: --> [7:CONNECT] Aug 30 10:01:42.02: [ 1084]: SEND begin page Aug 30 10:01:42.02: [ 1084]: <-- data [1025] Aug 30 10:01:42.02: [ 1084]: <-- data [1024] Aug 30 10:01:42.02: [ 1084]: <-- data [1024] Aug 30 10:01:42.02: [ 1084]: <-- data [1024] Aug 30 10:01:42.02: [ 1084]: <-- data [1024] Aug 30 10:01:43.02: [ 1084]: <-- data [1024] Aug 30 10:01:43.02: [ 1084]: <-- data [830] Aug 30 10:01:43.02: [ 1084]: SENT 6970 bytes of data Aug 30 10:01:43.02: [ 1084]: SEND 2D RTC Aug 30 10:01:43.02: [ 1084]: <-- data [30] Aug 30 10:01:43.02: [ 1084]: <-- data [2] Aug 30 10:01:43.02: [ 1084]: SEND end page Aug 30 10:01:46.34: [ 1084]: --> [2:] Aug 30 10:01:46.34: [ 1084]: --> [2:OK] Aug 30 10:01:46.34: [ 1084]: DELAY 200 ms Aug 30 10:01:46.54: [ 1084]: SEND send EOP (no more pages or documents) Aug 30 10:01:46.54: [ 1084]: <-- [9:AT+FTH=3\r] Aug 30 10:01:46.56: [ 1084]: --> [7:CONNECT] Aug 30 10:01:46.56: [ 1084]: <-- HDLC<3:FF C8 F4> Aug 30 10:01:46.56: [ 1084]: <-- data [3] Aug 30 10:01:46.56: [ 1084]: <-- data [2] Aug 30 10:01:47.80: [ 1084]: --> [2:OK] Aug 30 10:01:47.80: [ 1084]: <-- [9:AT+FRH=3\r] Aug 30 10:01:48.00: [ 1084]: --> [7:CONNECT] Aug 30 10:01:49.08: [ 1084]: --> HDLC<3:FF C8 31> Aug 30 10:01:49.08: [ 1084]: --> [2:OK] Aug 30 10:01:49.08: [ 1084]: SEND recv MCF (message confirmation) Aug 30 10:01:49.08: [ 1084]: SEND FAX (00000034): FROM dwright@spca.org TO xxx-xxxx-xxxx(page 1 of 1 sent in 0:14) Aug 30 10:01:49.08: [ 1084]: SEND FAX (00000034): FROM dwright@spca.org TO xxx-xxx-xxxx (docq/doc21.ps;40 sent in 0:14) Aug 30 10:01:49.08: [ 1084]: <-- [9:AT+FTH=3\r] Aug 30 10:01:49.10: [ 1084]: --> [7:CONNECT] Aug 30 10:01:49.10: [ 1084]: <-- HDLC<3:FF C8 DF> Aug 30 10:01:49.10: [ 1084]: <-- data [3] Aug 30 10:01:49.10: [ 1084]: <-- data [2] Aug 30 10:01:50.35: [ 1084]: --> [2:OK] Aug 30 10:01:50.35: [ 1084]: MODEM input buffering enabled Aug 30 10:01:50.35: [ 1084]: <-- [5:ATH0\r] Aug 30 10:01:50.86: [ 1084]: --> [2:OK] Aug 30 10:01:50.86: [ 1084]: MODEM set DTR OFF Aug 30 10:01:50.86: [ 1084]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5) Aug 30 10:01:50.86: [ 1084]: SESSION END Aug 30 10:02:58.59: [ 1141]: SESSION BEGIN 00000035 12149727167835 Aug 30 10:02:58.59: [ 1141]: HylaFAX (tm) Version 4.1 Aug 30 10:02:58.59: [ 1141]: SEND FAX: JOB 21 DEST xxx-xx-xxxx COMMID 00000035 Aug 30 10:02:58.59: [ 1141]: DEVICE '/dev/ttyS0' Aug 30 10:02:58.59: [ 1141]: MODEM set DTR OFF Aug 30 10:02:58.59: [ 1141]: DELAY 75 ms Aug 30 10:02:58.67: [ 1141]: MODEM set DTR ON Aug 30 10:02:58.67: [ 1141]: DELAY 2600 ms Aug 30 10:03:01.27: [ 1141]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS Aug 30 10:03:01.27: [ 1141]: MODEM flush i/o Aug 30 10:03:01.27: [ 1141]: <-- [4:ATZ\r] Aug 30 10:03:01.48: [ 1141]: --> [2:OK] Aug 30 10:03:01.48: [ 1141]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r] Aug 30 10:03:01.50: [ 1141]: --> [21:AT&B1&N0&S0*F0S38.3=1] Aug 30 10:03:01.50: [ 1141]: --> [2:OK] Aug 30 10:03:01.50: [ 1141]: <-- [5:ATE0\r] Aug 30 10:03:01.51: [ 1141]: --> [4:ATE0] Aug 30 10:03:01.51: [ 1141]: --> [2:OK] Aug 30 10:03:01.51: [ 1141]: <-- [5:ATV1\r] Aug 30 10:03:01.52: [ 1141]: --> [2:OK] Aug 30 10:03:01.52: [ 1141]: <-- [5:ATQ0\r] Aug 30 10:03:01.53: [ 1141]: --> [2:OK] Aug 30 10:03:01.53: [ 1141]: <-- [7:ATS0=0\r] Aug 30 10:03:01.54: [ 1141]: --> [2:OK] Aug 30 10:03:01.54: [ 1141]: <-- [7:ATS8=2\r] Aug 30 10:03:01.55: [ 1141]: --> [2:OK] Aug 30 10:03:01.55: [ 1141]: <-- [8:ATS7=60\r] Aug 30 10:03:01.56: [ 1141]: --> [2:OK] Aug 30 10:03:01.56: [ 1141]: <-- [6:AT&H3\r] Aug 30 10:03:01.57: [ 1141]: --> [2:OK] Aug 30 10:03:01.57: [ 1141]: <-- [6:AT&D2\r] Aug 30 10:03:01.58: [ 1141]: --> [2:OK] Aug 30 10:03:01.58: [ 1141]: <-- [6:AT&C1\r] Aug 30 10:03:01.59: [ 1141]: --> [2:OK] Aug 30 10:03:01.59: [ 1141]: <-- [12:AT+FCLASS=1\r] Aug 30 10:03:01.71: [ 1141]: --> [2:OK] Aug 30 10:03:01.71: [ 1141]: <-- [9:AT+FAA=1\r] Aug 30 10:03:01.72: [ 1141]: --> [2:OK] Aug 30 10:03:01.72: [ 1141]: <-- [7:ATM1L1\r] Aug 30 10:03:01.73: [ 1141]: --> [2:OK] Aug 30 10:03:01.73: [ 1141]: STATE CHANGE: RUNNING -> SENDING Aug 30 10:03:01.73: [ 1141]: MODEM input buffering enabled Aug 30 10:03:01.73: [ 1141]: <-- [12:AT+FCLASS=1\r] Aug 30 10:03:01.96: [ 1141]: --> [2:OK] Aug 30 10:03:01.96: [ 1141]: DIAL 9727167835 Aug 30 10:03:01.96: [ 1141]: <-- [15:ATDT9727167835\r] Aug 30 10:03:24.94: [ 1141]: --> [7:CONNECT] Aug 30 10:03:24.94: [ 1141]: MODEM input buffering disabled Aug 30 10:03:27.02: [ 1141]: --> HDLC<43:FF C0 04 00 00 9E 00 00 00 69 F0 90 C8 00 08 00 48 A9 03 0B 1F 01 82 80 92 40 9C EC 4C EC 8C 6C EC 1C CC AC 04 04 04 04 04 04 C0> Aug 30 10:03:27.03: [ 1141]: --> [2:OK] Aug 30 10:03:27.03: [ 1141]: REMOTE NSF "00 00 79 00 00 00 96 0F 09 13 00 10 00 12 95 C0 D0 F8 80 41 01 49 02 39 37 32 37 31 36 37 38 33 35 20 20 20 20 20 20 03 FD" Aug 30 10:03:27.03: [ 1141]: NSF remote fax equipment: Panasonic Aug 30 10:03:27.03: [ 1141]: NSF remote station ID: "9727167835 " Aug 30 10:03:27.03: [ 1141]: <-- [9:AT+FRH=3\r] Aug 30 10:03:27.05: [ 1141]: --> [7:CONNECT] Aug 30 10:03:27.72: [ 1141]: --> HDLC<23:FF C0 02 AC CC 1C EC 6C 8C EC 4C EC 9C 9C 04 04 04 04 04 04 04 04 04> Aug 30 10:03:27.72: [ 1141]: --> [2:OK] Aug 30 10:03:27.72: [ 1141]: REMOTE CSI "99727167835" Aug 30 10:03:27.72: [ 1141]: <-- [9:AT+FRH=3\r] Aug 30 10:03:27.74: [ 1141]: --> [7:CONNECT] Aug 30 10:03:28.05: [ 1141]: --> HDLC<9:FF C8 01 04 77 1F 23 01 88> Aug 30 10:03:28.05: [ 1141]: --> [2:OK] Aug 30 10:03:28.05: [ 1141]: REMOTE best rate 14400 bit/s Aug 30 10:03:28.05: [ 1141]: REMOTE max page width 1728 pixels in 215 mm Aug 30 10:03:28.05: [ 1141]: REMOTE max unlimited page length Aug 30 10:03:28.05: [ 1141]: REMOTE best vres 7.7 line/mm Aug 30 10:03:28.05: [ 1141]: REMOTE best format 2-D MMR Aug 30 10:03:28.05: [ 1141]: REMOTE supports T.30 Annex A, ECM Aug 30 10:03:28.05: [ 1141]: REMOTE best 0 ms/scanline Aug 30 10:03:28.05: [ 1141]: USE 14400 bit/s Aug 30 10:03:28.05: [ 1141]: USE 0 ms/scanline Aug 30 10:03:28.05: [ 1141]: SEND file "docq/doc22.ps;00" Aug 30 10:03:28.05: [ 1141]: USE page width 1728 pixels in 215 mm Aug 30 10:03:28.05: [ 1141]: USE unlimited page length Aug 30 10:03:28.05: [ 1141]: USE 3.85 line/mm Aug 30 10:03:28.05: [ 1141]: USE 1-D MR Aug 30 10:03:28.05: [ 1141]: SEND training at v.17 14400 bit/s Aug 30 10:03:28.05: [ 1141]: <-- [9:AT+FTH=3\r] Aug 30 10:03:28.07: [ 1141]: --> [7:CONNECT] Aug 30 10:03:28.07: [ 1141]: <-- HDLC<23:FF C0 C2 0E AE 2E A6 CA E6 76 96 16 2E F6 72 04 04 04 04 04 04 04 04> Aug 30 10:03:28.07: [ 1141]: <-- data [23] Aug 30 10:03:28.07: [ 1141]: <-- data [2] Aug 30 10:03:29.79: [ 1141]: --> [7:CONNECT] Aug 30 10:03:29.79: [ 1141]: <-- HDLC<6:FF C8 C1 00 44 1E> Aug 30 10:03:29.79: [ 1141]: <-- data [6] Aug 30 10:03:29.79: [ 1141]: <-- data [2] Aug 30 10:03:30.12: [ 1141]: --> [2:OK] Aug 30 10:03:30.12: [ 1141]: DELAY 75 ms Aug 30 10:03:30.20: [ 1141]: <-- [11:AT+FTM=145\r] Aug 30 10:03:30.22: [ 1141]: --> [7:CONNECT] Aug 30 10:03:30.22: [ 1141]: <-- data [1024] Aug 30 10:03:30.22: [ 1141]: <-- data [1024] Aug 30 10:03:30.22: [ 1141]: <-- data [652] Aug 30 10:03:30.22: [ 1141]: <-- data [2] Aug 30 10:03:33.36: [ 1141]: --> [2:OK] Aug 30 10:03:33.36: [ 1141]: <-- [9:AT+FRH=3\r] Aug 30 10:03:34.10: [ 1141]: --> [7:CONNECT] Aug 30 10:03:35.20: [ 1141]: --> HDLC<3:FF C8 21> Aug 30 10:03:35.20: [ 1141]: --> [2:OK] Aug 30 10:03:35.20: [ 1141]: TRAINING succeeded Aug 30 10:03:35.20: [ 1141]: DELAY 75 ms Aug 30 10:03:35.28: [ 1141]: <-- [11:AT+FTM=146\r] Aug 30 10:03:35.30: [ 1141]: --> [7:CONNECT] Aug 30 10:03:35.30: [ 1141]: SEND begin page Aug 30 10:03:35.30: [ 1141]: <-- data [1026] Aug 30 10:03:35.30: [ 1141]: <-- data [523] Aug 30 10:03:35.30: [ 1141]: SENT 1526 bytes of data Aug 30 10:03:35.30: [ 1141]: SEND 1D RTC Aug 30 10:03:35.30: [ 1141]: <-- data [29] Aug 30 10:03:35.30: [ 1141]: <-- data [2] Aug 30 10:03:35.30: [ 1141]: SEND end page Aug 30 10:03:36.60: [ 1141]: --> [2:OK] Aug 30 10:03:36.60: [ 1141]: DELAY 200 ms Aug 30 10:03:36.80: [ 1141]: SEND send EOP (no more pages or documents) Aug 30 10:03:36.80: [ 1141]: <-- [9:AT+FTH=3\r] Aug 30 10:03:36.82: [ 1141]: --> [7:CONNECT] Aug 30 10:03:36.82: [ 1141]: <-- HDLC<3:FF C8 F4> Aug 30 10:03:36.82: [ 1141]: <-- data [3] Aug 30 10:03:36.82: [ 1141]: <-- data [2] Aug 30 10:03:38.06: [ 1141]: --> [2:OK] Aug 30 10:03:38.06: [ 1141]: <-- [9:AT+FRH=3\r] Aug 30 10:03:38.67: [ 1141]: --> [7:CONNECT] Aug 30 10:03:39.77: [ 1141]: --> HDLC<3:FF C8 31> Aug 30 10:03:39.77: [ 1141]: --> [2:OK] Aug 30 10:03:39.77: [ 1141]: SEND recv MCF (message confirmation) Aug 30 10:03:39.77: [ 1141]: SEND FAX (00000035): FROM dwright@spca.org TOxxx-xxx-xxxx (page 1 of 1 sent in 0:11) Aug 30 10:03:39.77: [ 1141]: SEND FAX (00000035): FROM dwright@spca.org TO xxx-xxx-xxxx(docq/doc22.ps;00 sent in 0:11) Aug 30 10:03:39.77: [ 1141]: <-- [9:AT+FTH=3\r] Aug 30 10:03:39.79: [ 1141]: --> [7:CONNECT] Aug 30 10:03:39.79: [ 1141]: <-- HDLC<3:FF C8 DF> Aug 30 10:03:39.79: [ 1141]: <-- data [3] Aug 30 10:03:39.79: [ 1141]: <-- data [2] Aug 30 10:03:41.04: [ 1141]: --> [2:OK] Aug 30 10:03:41.04: [ 1141]: MODEM input buffering enabled Aug 30 10:03:41.04: [ 1141]: <-- [5:ATH0\r] Aug 30 10:03:41.55: [ 1141]: --> [2:OK] Aug 30 10:03:41.55: [ 1141]: MODEM set DTR OFF Aug 30 10:03:41.55: [ 1141]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5) Aug 30 10:03:41.55: [ 1141]: SESSION END ug 30 10:01:07 yesdan FaxSend[1084]: STATE CHANGE: BASE -> RUNNING Aug 30 10:01:07 yesdan FaxSend[1084]: MODEM input buffering disabled Aug 30 10:01:07 yesdan FaxSend[1084]: HylaFAX (tm) Version 4.1 Aug 30 10:01:07 yesdan FaxSend[1084]: SEND FAX: JOB 20 DEST xxx-xxx-xxxx COMMID 00000034 Aug 30 10:01:07 yesdan FaxSend[1084]: DEVICE '/dev/ttyS0' Aug 30 10:01:50 yesdan FaxQueuer[939]: NOTIFY: bin/notify "doneq/q20" "done" "0:48" Aug 30 10:02:05 yesdan FaxGetty[978]: MODEM set DTR OFF Aug 30 10:02:05 yesdan FaxGetty[978]: DELAY 75 ms Aug 30 10:02:05 yesdan FaxGetty[978]: MODEM set DTR ON Aug 30 10:02:05 yesdan FaxGetty[978]: DELAY 2600 ms Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM flush i/o Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [4:ATZ\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [21:AT&B1&N0&S0*F0S38.3=1] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [5:ATE0\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [4:ATE0] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [5:ATV1\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [5:ATQ0\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [7:ATS0=0\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [7:ATS8=2\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [8:ATS7=60\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [6:AT&H3\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [6:AT&D2\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [6:AT&C1\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=?\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [13:0,1,2,2.0,6,8] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports "Data" Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports "Class 1" Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports "Class 2" Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports "Class 2.0" Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports "Voice" Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=1\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [9:AT+FMFR?\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [5:ZyXEL] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM: Mfr ZyXEL Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [9:AT+FREV?\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [18:U1496E V 6.22 P ] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM: Revision U1496E V 6.22 P Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [9:AT+FTM=?\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 3.85 line/mm Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 7.7 line/mm Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 2400 bit/s Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 4800 bit/s Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 7200 bit/s Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 9600 bit/s Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 12000 bit/s Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 14400 bit/s Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports page width 1728 pixels in 215 mm Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports page width 2048 pixels in 255 mm Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports page width 2432 pixels in 303 mm Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports A4 page length (297 mm) Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports B4 page length (364 mm) Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports unlimited page length Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 1-D MR Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 2-D MR Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 0 ms/scanline Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 5 ms/scanline Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 10 ms, 5 ms/scanline Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 10 ms/scanline Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 20 ms, 10 ms/scanline Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 20 ms/scanline Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 40 ms, 20 ms/scanline Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM Supports 40 ms/scanline Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [9:AT+FRM=?\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=1\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [9:AT+FAA=1\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM ZYXEL /U1496E V 6.22 P Aug 30 10:02:08 yesdan FaxGetty[978]: <-- [7:ATM1L1\r] Aug 30 10:02:08 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:02:08 yesdan FaxGetty[978]: STATE CHANGE: LOCKWAIT -> RUNNING Aug 30 10:02:08 yesdan FaxGetty[978]: MODEM input buffering disabled Aug 30 10:02:53 yesdan FaxSend[1141]: MODEM set DTR OFF Aug 30 10:02:53 yesdan FaxSend[1141]: DELAY 75 ms Aug 30 10:02:53 yesdan FaxSend[1141]: MODEM set DTR ON Aug 30 10:02:53 yesdan FaxSend[1141]: DELAY 2600 ms Aug 30 10:02:55 yesdan FaxSend[1141]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS Aug 30 10:02:55 yesdan FaxSend[1141]: MODEM flush i/o Aug 30 10:02:55 yesdan FaxSend[1141]: <-- [4:ATZ\r] Aug 30 10:02:56 yesdan FaxGetty[978]: ANSWER: Can not lock modem device Aug 30 10:02:56 yesdan FaxGetty[978]: STATE CHANGE: RUNNING -> LOCKWAIT (timeout 30) Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r] Aug 30 10:02:56 yesdan FaxSend[1141]: --> [21:AT&B1&N0&S0*F0S38.3=1] Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [5:ATE0\r] Aug 30 10:02:56 yesdan FaxSend[1141]: --> [4:ATE0] Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [5:ATV1\r] Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [5:ATQ0\r] Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [7:ATS0=0\r] Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [7:ATS8=2\r] Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [8:ATS7=60\r] Aug 30 10:02:56 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:56 yesdan FaxSend[1141]: <-- [6:AT&H3\r] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [6:AT&D2\r] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [6:AT&C1\r] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [12:AT+FCLASS=?\r] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [13:0,1,2,2.0,6,8] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports "Data" Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports "Class 1" Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports "Class 2" Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports "Class 2.0" Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports "Voice" Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [12:AT+FCLASS=1\r] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [9:AT+FMFR?\r] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [5:ZyXEL] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM: Mfr ZyXEL Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [9:AT+FREV?\r] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [18:U1496E V 6.22 P ] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM: Revision U1496E V 6.22 P Aug 30 10:02:57 yesdan FaxSend[1141]: <-- [9:AT+FTM=?\r] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Aug 30 10:02:57 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 3.85 line/mm Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 7.7 line/mm Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 2400 bit/s Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 4800 bit/s Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 7200 bit/s Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 9600 bit/s Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 12000 bit/s Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 14400 bit/s Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports page width 1728 pixels in 215 mm Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports page width 2048 pixels in 255 mm Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports page width 2432 pixels in 303 mm Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports A4 page length (297 mm) Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports B4 page length (364 mm) Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports unlimited page length Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 1-D MR Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 2-D MR Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 0 ms/scanline Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 5 ms/scanline Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 10 ms, 5 ms/scanline Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 10 ms/scanline Aug 30 10:02:57 yesdan FaxSend[1141]: MODEM Supports 20 ms, 10 ms/scanline Aug 30 10:02:58 yesdan FaxSend[1141]: MODEM Supports 20 ms/scanline Aug 30 10:02:58 yesdan FaxSend[1141]: MODEM Supports 40 ms, 20 ms/scanline Aug 30 10:02:58 yesdan FaxSend[1141]: MODEM Supports 40 ms/scanline Aug 30 10:02:58 yesdan FaxSend[1141]: <-- [9:AT+FRM=?\r] Aug 30 10:02:58 yesdan FaxSend[1141]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Aug 30 10:02:58 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:58 yesdan FaxSend[1141]: <-- [12:AT+FCLASS=1\r] Aug 30 10:02:58 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:58 yesdan FaxSend[1141]: <-- [9:AT+FAA=1\r] Aug 30 10:02:58 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:58 yesdan FaxSend[1141]: MODEM ZYXEL /U1496E V 6.22 P Aug 30 10:02:58 yesdan FaxSend[1141]: <-- [7:ATM1L1\r] Aug 30 10:02:58 yesdan FaxSend[1141]: --> [2:OK] Aug 30 10:02:58 yesdan FaxSend[1141]: STATE CHANGE: BASE -> RUNNING Aug 30 10:02:58 yesdan FaxSend[1141]: MODEM input buffering disabled Aug 30 10:02:58 yesdan FaxSend[1141]: HylaFAX (tm) Version 4.1 Aug 30 10:02:58 yesdan FaxSend[1141]: SEND FAX: JOB 21 DEST xxx-xxx-xxxx COMMID 00000035 Aug 30 10:02:58 yesdan FaxSend[1141]: DEVICE '/dev/ttyS0' Aug 30 10:03:41 yesdan FaxQueuer[939]: NOTIFY: bin/notify "doneq/q21" "done" "0:48" Aug 30 10:03:56 yesdan FaxGetty[978]: MODEM set DTR OFF Aug 30 10:03:56 yesdan FaxGetty[978]: DELAY 75 ms Aug 30 10:03:56 yesdan FaxGetty[978]: MODEM set DTR ON Aug 30 10:03:56 yesdan FaxGetty[978]: DELAY 2600 ms Aug 30 10:03:58 yesdan FaxGetty[978]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS Aug 30 10:03:58 yesdan FaxGetty[978]: MODEM flush i/o Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [4:ATZ\r] Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r] Aug 30 10:03:58 yesdan FaxGetty[978]: --> [21:AT&B1&N0&S0*F0S38.3=1] Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [5:ATE0\r] Aug 30 10:03:58 yesdan FaxGetty[978]: --> [4:ATE0] Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [5:ATV1\r] Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [5:ATQ0\r] Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [7:ATS0=0\r] Aug 30 10:03:58 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:58 yesdan FaxGetty[978]: <-- [7:ATS8=2\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [8:ATS7=60\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [6:AT&H3\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [6:AT&D2\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [6:AT&C1\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=?\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [13:0,1,2,2.0,6,8] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports "Data" Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports "Class 1" Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports "Class 2" Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports "Class 2.0" Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports "Voice" Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=1\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [9:AT+FMFR?\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [5:ZyXEL] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM: Mfr ZyXEL Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [9:AT+FREV?\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [18:U1496E V 6.22 P ] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM: Revision U1496E V 6.22 P Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [9:AT+FTM=?\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 3.85 line/mm Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 7.7 line/mm Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 2400 bit/s Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 4800 bit/s Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 7200 bit/s Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 9600 bit/s Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 12000 bit/s Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 14400 bit/s Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports page width 1728 pixels in 215 mm Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports page width 2048 pixels in 255 mm Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports page width 2432 pixels in 303 mm Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports A4 page length (297 mm) Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports B4 page length (364 mm) Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports unlimited page length Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 1-D MR Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 2-D MR Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 0 ms/scanline Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 5 ms/scanline Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 10 ms, 5 ms/scanline Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 10 ms/scanline Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 20 ms, 10 ms/scanline Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 20 ms/scanline Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 40 ms, 20 ms/scanline Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM Supports 40 ms/scanline Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [9:AT+FRM=?\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [12:AT+FCLASS=1\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [9:AT+FAA=1\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM ZYXEL /U1496E V 6.22 P Aug 30 10:03:59 yesdan FaxGetty[978]: <-- [7:ATM1L1\r] Aug 30 10:03:59 yesdan FaxGetty[978]: --> [2:OK] Aug 30 10:03:59 yesdan FaxGetty[978]: STATE CHANGE: LOCKWAIT -> RUNNING Aug 30 10:03:59 yesdan FaxGetty[978]: MODEM input buffering disabled Aug 30 10:04:44 yesdan FaxSend[1155]: MODEM set DTR OFF Aug 30 10:04:44 yesdan FaxSend[1155]: DELAY 75 ms Aug 30 10:04:44 yesdan FaxSend[1155]: MODEM set DTR ON Aug 30 10:04:44 yesdan FaxSend[1155]: DELAY 2600 ms Aug 30 10:04:46 yesdan FaxSend[1155]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS Aug 30 10:04:46 yesdan FaxSend[1155]: MODEM flush i/o Aug 30 10:04:46 yesdan FaxSend[1155]: <-- [4:ATZ\r] Aug 30 10:04:47 yesdan FaxGetty[978]: ANSWER: Can not lock modem device Aug 30 10:04:47 yesdan FaxGetty[978]: STATE CHANGE: RUNNING -> LOCKWAIT (timeout 30) Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r] Aug 30 10:04:47 yesdan FaxSend[1155]: --> [21:AT&B1&N0&S0*F0S38.3=1] Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [5:ATE0\r] Aug 30 10:04:47 yesdan FaxSend[1155]: --> [4:ATE0] Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [5:ATV1\r] Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [5:ATQ0\r] Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [7:ATS0=0\r] Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [7:ATS8=2\r] Aug 30 10:04:47 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:47 yesdan FaxSend[1155]: <-- [8:ATS7=60\r] Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [6:AT&H3\r] Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [6:AT&D2\r] Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [6:AT&C1\r] Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [12:AT+FCLASS=?\r] Aug 30 10:04:48 yesdan FaxSend[1155]: --> [13:0,1,2,2.0,6,8] Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports "Data" Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports "Class 1" Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports "Class 2" Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports "Class 2.0" Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM Supports "Voice" Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [12:AT+FCLASS=1\r] Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [9:AT+FMFR?\r] Aug 30 10:04:48 yesdan FaxSend[1155]: --> [5:ZyXEL] Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM: Mfr ZyXEL Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [9:AT+FREV?\r] Aug 30 10:04:48 yesdan FaxSend[1155]: --> [18:U1496E V 6.22 P ] Aug 30 10:04:48 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:48 yesdan FaxSend[1155]: MODEM: Revision U1496E V 6.22 P Aug 30 10:04:48 yesdan FaxSend[1155]: <-- [9:AT+FTM=?\r] Aug 30 10:04:49 yesdan FaxSend[1155]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Aug 30 10:04:49 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 3.85 line/mm Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 7.7 line/mm Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 2400 bit/s Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 4800 bit/s Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 7200 bit/s Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 9600 bit/s Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 12000 bit/s Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 14400 bit/s Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports page width 1728 pixels in 215 mm Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports page width 2048 pixels in 255 mm Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports page width 2432 pixels in 303 mm Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports A4 page length (297 mm) Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports B4 page length (364 mm) Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports unlimited page length Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 1-D MR Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 2-D MR Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 0 ms/scanline Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 5 ms/scanline Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 10 ms, 5 ms/scanline Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 10 ms/scanline Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 20 ms, 10 ms/scanline Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 20 ms/scanline Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 40 ms, 20 ms/scanline Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM Supports 40 ms/scanline Aug 30 10:04:49 yesdan FaxSend[1155]: <-- [9:AT+FRM=?\r] Aug 30 10:04:49 yesdan FaxSend[1155]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Aug 30 10:04:49 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:49 yesdan FaxSend[1155]: <-- [12:AT+FCLASS=1\r] Aug 30 10:04:49 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:49 yesdan FaxSend[1155]: <-- [9:AT+FAA=1\r] Aug 30 10:04:49 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM ZYXEL /U1496E V 6.22 P Aug 30 10:04:49 yesdan FaxSend[1155]: <-- [7:ATM1L1\r] Aug 30 10:04:49 yesdan FaxSend[1155]: --> [2:OK] Aug 30 10:04:49 yesdan FaxSend[1155]: STATE CHANGE: BASE -> RUNNING Aug 30 10:04:49 yesdan FaxSend[1155]: MODEM input buffering disabled Aug 30 10:04:49 yesdan FaxSend[1155]: HylaFAX (tm) Version 4.1 ____________________ HylaFAX(tm) Users Mailing List _______________________ To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
- Follow-Ups:
- Re: [hylafax-users] zyxel u-1496e config
- From: Lee Howard
- Re: [hylafax-users] zyxel u-1496e config
- Prev by Date: Re: [hylafax-users] Viewing Tifs
- Next by Date: Re: [hylafax-users] zyxel u-1496e config
- Previous by thread: Re: [hylafax-users] zyxel u-1496e config
- Next by thread: Re: [hylafax-users] zyxel u-1496e config
- Index(es):
Project hosted by iFAX Solutions