Re: [hylafax-users] zyxel u-1496e config

["Dan" <dwright@spca.org>]

At 04:23 PM 8/27/01 -0500, Dan wrote:
>I just installed redhat 7.1 and hylafax 4.1 my modem is a
>Zyxel u-1496e with the latest firmware. I have tried this modem in
>both class 1 and class 2.  I am getting lots (all most all) of:  Failure to
>train remote
> modem at 2400 bps or minimum speed; Giving up after 3 attempts to send
same
>page

It's probably not your config file.  Would you please send a session log?

Lee.

Lee sorry here is a another one the first one was from a config file that i
changed
the rtscts on to xonxoff hopping that it would work.

thanks Dan

Your facsimile job to xxx-xxx-xxxx failed because:
    Failure to train remote modem at 2400 bps or minimum speed; Giving up
after 3 attempts to send same page

    ---- Transcript of session follows ----

Aug 21 17:51:35.69: [ 1569]: SESSION BEGIN 00000014 12149728694975
Aug 21 17:51:35.69: [ 1569]: HylaFAX (tm) Version 4.1
Aug 21 17:51:35.69: [ 1569]: SEND FAX: JOB 6 DEST xxx-xxx-xxxx COMMID
00000014
Aug 21 17:51:35.69: [ 1569]: DEVICE '/dev/ttyS0'
Aug 21 17:51:35.69: [ 1569]: DELAY 75 ms
Aug 21 17:51:35.76: [ 1569]: DELAY 2600 ms
Aug 21 17:51:38.36: [ 1569]: <-- [4:ATZ\r]
Aug 21 17:51:38.57: [ 1569]: --> [2:OK]
Aug 21 17:51:38.57: [ 1569]: <-- [22:AT&B1&N0&S0*F0S38.3=1\r]
Aug 21 17:51:38.59: [ 1569]: --> [21:AT&B1&N0&S0*F0S38.3=1]
Aug 21 17:51:38.59: [ 1569]: --> [2:OK]
Aug 21 17:51:38.59: [ 1569]: <-- [5:ATE0\r]
Aug 21 17:51:38.60: [ 1569]: --> [4:ATE0]
Aug 21 17:51:38.60: [ 1569]: --> [2:OK]
Aug 21 17:51:38.60: [ 1569]: <-- [5:ATV1\r]
Aug 21 17:51:38.61: [ 1569]: --> [2:OK]
Aug 21 17:51:38.61: [ 1569]: <-- [5:ATQ0\r]
Aug 21 17:51:38.62: [ 1569]: --> [2:OK]
Aug 21 17:51:38.62: [ 1569]: <-- [7:ATS0=0\r]
Aug 21 17:51:38.63: [ 1569]: --> [2:OK]
Aug 21 17:51:38.63: [ 1569]: <-- [7:ATS8=2\r]
Aug 21 17:51:38.64: [ 1569]: --> [2:OK]
Aug 21 17:51:38.64: [ 1569]: <-- [8:ATS7=60\r]
Aug 21 17:51:38.65: [ 1569]: --> [2:OK]
Aug 21 17:51:38.65: [ 1569]: <-- [6:AT&H3\r]
Aug 21 17:51:38.66: [ 1569]: --> [2:OK]
Aug 21 17:51:38.66: [ 1569]: <-- [6:AT&D2\r]
Aug 21 17:51:38.67: [ 1569]: --> [2:OK]
Aug 21 17:51:38.67: [ 1569]: <-- [6:AT&C1\r]
Aug 21 17:51:38.68: [ 1569]: --> [2:OK]
Aug 21 17:51:38.68: [ 1569]: <-- [12:AT+FCLASS=1\r]
Aug 21 17:51:38.80: [ 1569]: --> [2:OK]
Aug 21 17:51:38.80: [ 1569]: <-- [9:AT+FAA=1\r]
Aug 21 17:51:38.81: [ 1569]: --> [2:OK]
Aug 21 17:51:38.81: [ 1569]: <-- [5:ATM0\r]
Aug 21 17:51:38.82: [ 1569]: --> [2:OK]
Aug 21 17:51:38.82: [ 1569]: <-- [12:AT+FCLASS=1\r]
Aug 21 17:51:39.05: [ 1569]: --> [2:OK]
Aug 21 17:51:39.06: [ 1569]: DIAL 9728694975
Aug 21 17:51:39.06: [ 1569]: <-- [15:ATDT9728694975\r]
Aug 21 17:51:59.60: [ 1569]: --> [7:CONNECT]
Aug 21 17:52:01.58: [ 1569]: --> [2:OK]
Aug 21 17:52:01.58: [ 1569]: REMOTE NSF "00 00 31 00 EE B8 44 86 0D DD 00 00
DD DD 00 00 DD DD DD DD DD 01 08 21 02 17 54 24 ED 23 90 00 00 F4 01 FF"
Aug 21 17:52:01.58: [ 1569]: NSF remote fax equipment: Sharp/Olivetti
Aug 21 17:52:01.58: [ 1569]: NSF remote station ID: "YYYYY"
Aug 21 17:52:01.58: [ 1569]: <-- [9:AT+FRH=3\r]
Aug 21 17:52:01.60: [ 1569]: --> [7:CONNECT]
Aug 21 17:52:02.28: [ 1569]: --> [2:OK]
Aug 21 17:52:02.28: [ 1569]: REMOTE CSI "214 561 9662"
Aug 21 17:52:02.28: [ 1569]: <-- [9:AT+FRH=3\r]
Aug 21 17:52:02.30: [ 1569]: --> [7:CONNECT]
Aug 21 17:52:02.54: [ 1569]: --> [2:OK]
Aug 21 17:52:02.54: [ 1569]: REMOTE best rate 14400 bit/s
Aug 21 17:52:02.54: [ 1569]: REMOTE max page width 1728 pixels in 215 mm
Aug 21 17:52:02.54: [ 1569]: REMOTE max unlimited page length
Aug 21 17:52:02.54: [ 1569]: REMOTE best vres 7.7 line/mm
Aug 21 17:52:02.54: [ 1569]: REMOTE best format 2-D MMR
Aug 21 17:52:02.54: [ 1569]: REMOTE supports T.30 Annex A, ECM
Aug 21 17:52:02.54: [ 1569]: REMOTE best 20 ms, 10 ms/scanline
Aug 21 17:52:02.54: [ 1569]: USE 14400 bit/s
Aug 21 17:52:02.54: [ 1569]: USE 20 ms, 10 ms/scanline
Aug 21 17:52:02.54: [ 1569]: SEND file "docq/doc7.ps;00"
Aug 21 17:52:02.55: [ 1569]: USE page width 1728 pixels in 215 mm
Aug 21 17:52:02.55: [ 1569]: USE unlimited page length
Aug 21 17:52:02.55: [ 1569]: USE 3.85 line/mm
Aug 21 17:52:02.55: [ 1569]: USE 1-D MR
Aug 21 17:52:02.55: [ 1569]: SEND training at v.17 14400 bit/s
Aug 21 17:52:02.55: [ 1569]: <-- [9:AT+FTH=3\r]
Aug 21 17:52:03.00: [ 1569]: --> [10:NO CARRIER]
Aug 21 17:52:03.00: [ 1569]: Error sending T.30 prologue frames
Aug 21 17:52:03.00: [ 1569]: SEND training at v.17 12000 bit/s
Aug 21 17:52:03.00: [ 1569]: <-- [9:AT+FTH=3\r]
Aug 21 17:52:03.01: [ 1569]: --> [5:ERROR]
Aug 21 17:52:03.01: [ 1569]: Error sending T.30 prologue frames
Aug 21 17:52:03.01: [ 1569]: SEND training at v.17 9600 bit/s
Aug 21 17:52:03.01: [ 1569]: <-- [9:AT+FTH=3\r]
Aug 21 17:52:03.02: [ 1569]: --> [5:ERROR]
Aug 21 17:52:03.02: [ 1569]: Error sending T.30 prologue frames
Aug 21 17:52:03.02: [ 1569]: SEND training at v.17 7200 bit/s
Aug 21 17:52:03.02: [ 1569]: <-- [9:AT+FTH=3\r]
Aug 21 17:52:03.03: [ 1569]: --> [5:ERROR]
Aug 21 17:52:03.03: [ 1569]: Error sending T.30 prologue frames
Aug 21 17:52:03.03: [ 1569]: SEND training at v.27ter 4800 bit/s
Aug 21 17:52:03.03: [ 1569]: <-- [9:AT+FTH=3\r]
Aug 21 17:52:03.04: [ 1569]: --> [5:ERROR]
Aug 21 17:52:03.04: [ 1569]: Error sending T.30 prologue frames
Aug 21 17:52:03.04: [ 1569]: SEND training at v.27ter fallback mode 2400
bit/s
Aug 21 17:52:03.04: [ 1569]: <-- [9:AT+FTH=3\r]
Aug 21 17:52:03.05: [ 1569]: --> [5:ERROR]
Aug 21 17:52:03.05: [ 1569]: Error sending T.30 prologue frames
Aug 21 17:52:03.05: [ 1569]: TRAINING failed
Aug 21 17:52:03.05: [ 1569]: SEND: Failure to train remote modem at 2400 bps
or minimum speed; Giving up after 3 attempts to send same page
"docq/doc7.ps;00", dirnum 0
Aug 21 17:52:03.05: [ 1569]: <-- [9:AT+FTH=3\r]
Aug 21 17:52:03.07: [ 1569]: --> [5:ERROR]
Aug 21 17:52:03.07: [ 1569]: <-- [5:ATH0\r]
Aug 21 17:52:03.38: [ 1569]: --> [2:OK]
Aug 21 17:52:03.38: [ 1569]: SESSION END

    ---- Unsent job status ----

   Destination: xxx-xxx-xxxx
         JobID: 6
       GroupID: 6
        Sender: Dan
      Mailaddr: dwright@spca.org
        CommID: 00000014
Submitted From: dan-2000
    Page Width: 194 (mm)
   Page Length: 281 (mm)
    Resolution: 98 (lpi)
        Status: Failure to train remote modem at 2400 bps or minimum speed;
Giving up after 3 attempts to send same page
       Dialogs: 3 (exchanges with remote device)
         Dials: 0 (consecutive failed calls to destination)
         Calls: 3 (total phone calls placed)
         Pages: 0 (pages transmitted)
      TotPages: 1 (total pages to transmit)
      Attempts: 3 (attempts to send current page)
        Dirnum: 0 (directory of next page to send)

    ---- Documents submitted for transmission ----

The following documents were submitted for transmission and are
available on the server for reuse until they are automatically
purged when this job is removed.  Documents may also be manually
removed using the faxrm command; consult faxrm(1) for information.

Filename                 Size Type
docq/doc7.ps            16060 PostScript

>does anyone have a modem config file that works good?  I tried the one that
>came with Hylafax but haven't had much luck.




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null