[hylafax-users] Sedlbauer ISDN card

[Moritz Both <mb@aldebaran.de>]

Greetings everyone,

we are playing with the relatively new Sedlbauer fax+ PCI ISDN card
and Hylafax, but with medium seccess only so far. I have searched the
mailing list archives without success and also sent a request for
support to Sedlbauer - so far I have not received an answer.

We use a RedHat 7.1 system and the Hylafax RPM version
hylafax-4.1-1rh7. Problems appear when trying to receive fax messages
from certain (old?) fax machines when the first page arrives cleanly
but transmission aborts after that. Session logs, some more system
info, kernel hisax module load messages etc. is appended.

Maybe somebody can help here? Can people confirm that this setup
(Sedlbauer / Hylafax) would regualrily work? Can someone with such a
setup send me a fax phone number so I could test if the old fax
machine I have also cannot send more than one page to this server or
if it works there?

Thanks for any comment,
Moritz Both

Aldebaran Daten- und Kommunikationssysteme GmbH
Tel. 0511 / 270416-0
Fax  0511 / 270416-33
http://www.aldebaran.de/



Aug 14 15:56:48 hl FaxGetty[3674]: ANSWER: FAX CONNECTION
Aug 14 15:57:39 hl FaxGetty[3674]: RECV FAX (00000006): from +49 511 713496, page 1 in 0:43, INF, 3.85 line/mm, 1-D MR, 9600 bit/s
Aug 14 15:57:42 hl FaxGetty[3674]: RECV FAX (00000006): recvq/fax00009.tif from +49 511 713496, route to <unspecified>, 1 pages in 0:54
Aug 14 15:57:44 hl FaxGetty[3674]: RECV FAX (00000006): session with +49 511 713496 terminated abnormally: T.30 T2 timeout, expected page not received
Aug 14 15:57:44 hl FaxGetty[3674]: RECV FAX: bin/faxrcvd "recvq/fax00009.tif" "ttyI0" "00000006" "T.30 T2 timeout, expected page not received"

recvq/fax00008.tif:
    Sender: +49 511 713496
     Pages: 1
   Quality: Normal
      Page: ISO A4
  Received: 2001:08:14 15:43:48
TimeToRecv: 0:42
SignalRate: 9600 bit/s
DataFormat: 1-D MR


The full document was not received because:

    T.30 T2 timeout, expected page not received

    ---- Transcript of session follows ----
Aug 14 15:43:35.01: [ 3631]: SESSION BEGIN 00000005 4951127041633
Aug 14 15:43:35.01: [ 3631]: <-- [4:ATA\r]
Aug 14 15:43:40.20: [ 3631]: --> [7:CONNECT]
Aug 14 15:43:40.20: [ 3631]: ANSWER: FAX CONNECTION
Aug 14 15:43:40.20: [ 3631]: RECV FAX: begin
Aug 14 15:43:40.20: [ 3631]: <-- data [23]
Aug 14 15:43:40.20: [ 3631]: <-- data [2]
Aug 14 15:43:40.24: [ 3631]: --> [7:CONNECT]
Aug 14 15:43:40.24: [ 3631]: <-- data [10]
Aug 14 15:43:40.24: [ 3631]: <-- data [2]
Aug 14 15:43:41.36: [ 3631]: --> [2:OK]
Aug 14 15:43:41.36: [ 3631]: <-- [9:AT+FRH=3\r]
Aug 14 15:43:41.74: [ 3631]: --> [7:CONNECT]
Aug 14 15:43:43.31: [ 3631]: --> [2:OK]
Aug 14 15:43:43.31: [ 3631]: REMOTE TSI "+49 511 713496"
Aug 14 15:43:43.31: [ 3631]: <-- [9:AT+FRH=3\r]
Aug 14 15:43:43.32: [ 3631]: --> [7:CONNECT]
Aug 14 15:43:43.64: [ 3631]: --> [2:OK]
Aug 14 15:43:43.64: [ 3631]: REMOTE wants 9600 bit/s
Aug 14 15:43:43.64: [ 3631]: REMOTE wants page width 1728 pixels in 215 mm
Aug 14 15:43:43.64: [ 3631]: REMOTE wants unlimited page length 
Aug 14 15:43:43.64: [ 3631]: REMOTE wants 3.85 line/mm
Aug 14 15:43:43.64: [ 3631]: REMOTE wants 1-D MR
Aug 14 15:43:43.64: [ 3631]: RECV training at v.29 9600 bit/s
Aug 14 15:43:43.64: [ 3631]: <-- [10:AT+FRM=96\r]
Aug 14 15:43:44.01: [ 3631]: --> [7:CONNECT]
Aug 14 15:43:45.61: [ 3631]: RECV: TCF 1913 bytes, 5% non-zero, 1809 zero-run
Aug 14 15:43:45.61: [ 3631]: --> [10:NO CARRIER]
Aug 14 15:43:45.61: [ 3631]: DELAY 75 ms
Aug 14 15:43:45.69: [ 3631]: <-- [9:AT+FTH=3\r]
Aug 14 15:43:47.33: [ 3631]: --> [7:CONNECT]
Aug 14 15:43:47.33: [ 3631]: <-- data [3]
Aug 14 15:43:47.33: [ 3631]: <-- data [2]
Aug 14 15:43:47.58: [ 3631]: --> [2:OK]
Aug 14 15:43:47.58: [ 3631]: TRAINING succeeded
Aug 14 15:43:47.58: [ 3631]: <-- [10:AT+FRM=96\r]
Aug 14 15:43:48.84: [ 3631]: --> [7:CONNECT]
Aug 14 15:43:48.84: [ 3631]: RECV: begin page
Aug 14 15:44:29.36: [ 3631]: RECV: 1145 total lines, 0 bad lines, 0 consecutive bad lines
Aug 14 15:44:29.36: [ 3631]: RECV: end page
Aug 14 15:44:29.36: [ 3631]: --> [10:NO CARRIER]
Aug 14 15:44:29.36: [ 3631]: <-- [9:AT+FRH=3\r]
Aug 14 15:44:29.50: [ 3631]: --> [7:CONNECT]
Aug 14 15:44:30.46: [ 3631]: --> [2:OK]
Aug 14 15:44:30.46: [ 3631]: RECV recv MPS (more pages, same document)
Aug 14 15:44:30.46: [ 3631]: DELAY 150 ms
Aug 14 15:44:30.61: [ 3631]: <-- [9:AT+FTH=3\r]
Aug 14 15:44:30.61: [ 3631]: --> [10:NO CARRIER]
Aug 14 15:44:30.61: [ 3631]: RECV send MCF (message confirmation)
Aug 14 15:44:30.61: [ 3631]: RECV FAX (00000005): from +49 511 713496, page 1 in 0:43, INF, 3.85 line/mm, 1-D MR, 9600 bit/s
Aug 14 15:44:30.61: [ 3631]: <-- [10:AT+FRM=96\r]
Aug 14 15:44:34.06: [ 3631]: --> [7:FCERROR]
Aug 14 15:44:34.06: [ 3631]: RECV FAX (00000005): recvq/fax00008.tif from +49 511 713496, route to <unspecified>, 1 pages in 0:54
Aug 14 15:44:34.06: [ 3631]: RECV FAX: T.30 T2 timeout, expected page not received
Aug 14 15:44:34.06: [ 3631]: <-- [9:AT+FTH=3\r]
Aug 14 15:44:35.70: [ 3631]: --> [7:CONNECT]
Aug 14 15:44:35.70: [ 3631]: <-- data [3]
Aug 14 15:44:35.70: [ 3631]: <-- data [2]
Aug 14 15:44:35.95: [ 3631]: --> [2:OK]
Aug 14 15:44:35.95: [ 3631]: RECV FAX (00000005): session with +49 511 713496 terminated abnormally: T.30 T2 timeout, expected page not received
Aug 14 15:44:35.95: [ 3631]: RECV FAX: bin/faxrcvd "recvq/fax00008.tif" "ttyI0" "00000005" "T.30 T2 timeout, expected page not received"



Aug 14 13:10:39 hl kernel: ISDN subsystem Rev: 1.114.6.8/1.94.6.1/1.140.6.3/1.85.6.2/1.21/1.5.6.3 loaded
Aug 14 13:10:39 hl kernel: HiSax: Linux Driver for passive ISDN cards
Aug 14 13:10:39 hl kernel: HiSax: Version 3.5 (module)
Aug 14 13:10:39 hl kernel: HiSax: Layer1 Revision 2.41.6.2
Aug 14 13:10:39 hl kernel: HiSax: Layer2 Revision 2.25.6.1
Aug 14 13:10:39 hl kernel: HiSax: TeiMgr Revision 2.17.6.1
Aug 14 13:10:39 hl kernel: HiSax: Layer3 Revision 2.17.6.2
Aug 14 13:10:39 hl kernel: HiSax: LinkLayer Revision 2.51.6.1
Aug 14 13:10:39 hl kernel: HiSax: Approval certification failed because of
Aug 14 13:10:39 hl kernel: HiSax: unauthorized source code changes
Aug 14 13:10:39 hl kernel: HiSax: Warning - no protocol specified
Aug 14 13:10:39 hl kernel: HiSax: using protocol EURO
Aug 14 13:10:39 hl kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
Aug 14 13:10:39 hl kernel: HiSax: Sedlbauer driver Rev. 1.25.6.4
Aug 14 13:10:39 hl kernel: PCI: Found IRQ 10 for device 00:0b.0
Aug 14 13:10:39 hl kernel: PCI: The same IRQ used for device 00:11.0
Aug 14 13:10:39 hl kernel: Sedlbauer: PCI subvendor:54 subid 1
Aug 14 13:10:39 hl kernel: Sedlbauer: PCI base adr 0x9000
Aug 14 13:10:39 hl kernel: Sedlbauer: defined at 0x9000-0x9100 IRQ 10
Aug 14 13:10:39 hl kernel: Sedlbauer: speed fax+ pci detected
Aug 14 13:10:39 hl kernel: Sedlbauer: ISAC version (0): 2086/2186 V1.1
Aug 14 13:10:39 hl kernel: Sedlbauer: resetting card
Aug 14 13:10:39 hl kernel: Sedlbauer: ISAR version 1
Aug 14 13:10:39 hl kernel: Sedlbauer Speed Fax +: IRQ 10 count 7182
Aug 14 13:10:39 hl kernel: Sedlbauer Speed Fax +: IRQ 10 count 7188
Aug 14 13:10:39 hl kernel: HiSax: DSS1 Rev. 2.30.6.1
Aug 14 13:10:39 hl kernel: HiSax: 2 channels added
Aug 14 13:10:39 hl kernel: HiSax: MAX_WAITING_CALLS added
Aug 14 13:10:39 hl kernel: Sedlbauer: resetting card
Aug 14 13:10:39 hl kernel: Testing ISAR version 1

[root@hl /root]# ls -l /usr/lib/isdn/ISAR.BIN
-rw-r--r--    1 root     root        62518 Feb 12  2001 /usr/lib/isdn/ISAR.BIN
[root@hl /root]# grep -i hisax /etc/modules.conf
alias char-major-43 hisax
options -k hisax type=28
post-install hisax /usr/sbin/hisaxctrl HiSax 9 /usr/lib/isdn/ISAR.BIN
[root@hl /root]# uname -a
Linux hl.aldebaran.de 2.4.2-2 #1 Sun Apr 8 20:41:30 EDT 2001 i686 unknown




Moritz Both

Aldebaran Daten- und Kommunikationssysteme GmbH
Tel. 0511 / 270416-0
Fax  0511 / 270416-33
http://www.aldebaran.de/




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null