[hylafax-users] faxgetty process stuck

[M�slix <mamboman@gmx.ch>]

Hi folks!

We have been using hylafax on SuseLinux 6.4 for about 6 months now and
it has alway worked just fine :)
But now ... it's doing weired things when receiving faxes. It answers an
incoming call but won't properly receive the fax.

Jul 02 10:42:58.04: [31960]: SESSION BEGIN 00000575 492018585855
Jul 02 10:42:58.04: [31960]: <-- [4:ATA\r]
Jul 02 10:43:04.24: [31960]: --> [7:CONNECT]
Jul 02 10:43:04.24: [31960]: ANSWER: FAX CONNECTION
Jul 02 10:43:04.24: [31960]: RECV FAX: begin
Jul 02 10:43:04.27: [31960]: <-- data [23]
Jul 02 10:43:04.27: [31960]: <-- data [2]
Jul 02 10:43:05.92: [31960]: --> [7:CONNECT]
Jul 02 10:43:05.92: [31960]: <-- data [10]
Jul 02 10:43:05.92: [31960]: <-- data [2]
Jul 02 10:43:06.47: [31960]: --> [2:OK]
Jul 02 10:43:06.47: [31960]: <-- [9:AT+FRH=3\r]
Jul 02 10:43:06.86: [31960]: --> [7:CONNECT]
Jul 02 10:43:08.31: [31960]: --> [2:OK]
Jul 02 10:43:08.31: [31960]: REMOTE TSI "INGRAM MACROTRON"
Jul 02 10:43:08.31: [31960]: <-- [9:AT+FRH=3\r]
Jul 02 10:43:08.33: [31960]: --> [7:CONNECT]
Jul 02 10:43:08.58: [31960]: --> [2:OK]
Jul 02 10:43:08.58: [31960]: REMOTE wants 14400 bit/s
Jul 02 10:43:08.58: [31960]: REMOTE wants page width 1728 pixels in 215
mm
Jul 02 10:43:08.58: [31960]: REMOTE wants unlimited page length 
Jul 02 10:43:08.58: [31960]: REMOTE wants 3.85 line/mm
Jul 02 10:43:08.58: [31960]: REMOTE wants 2-D MR
Jul 02 10:43:08.58: [31960]: RECV training at v.17 14400 bit/s
Jul 02 10:43:08.58: [31960]: <-- [11:AT+FRM=145\r]
Jul 02 10:43:10.34: [31960]: --> [7:CONNECT]
Jul 02 10:43:11.89: [31960]: RECV: TCF 2754 bytes, 1% non-zero, 2711
zero-run
Jul 02 10:43:11.89: [31960]: --> [10:NO CARRIER]
Jul 02 10:43:11.89: [31960]: DELAY 75 ms
Jul 02 10:43:11.97: [31960]: <-- [9:AT+FTH=3\r]
Jul 02 10:43:12.03: [31960]: --> [7:CONNECT]
Jul 02 10:43:12.03: [31960]: <-- data [3]
Jul 02 10:43:12.03: [31960]: <-- data [2]
Jul 02 10:43:13.34: [31960]: --> [2:OK]
Jul 02 10:43:13.34: [31960]: TRAINING succeeded
Jul 02 10:43:13.34: [31960]: <-- [11:AT+FRM=146\r]
Jul 02 10:43:14.30: [31960]: --> [7:CONNECT]
Jul 02 10:43:14.30: [31960]: RECV: begin page
Jul 02 10:52:48.59: [31960]: CLOSE /dev/ttyS0

To me, it seems as if our local modem just hangs up? 
One problem resulting from this (besides the fact that we cannot receive
faxes *g*) is that the faxgetty process hangs and uses about 40% cpu ->
which results in sloooow work on the server. I just send the term signal
to the process and it returns to "running and idle state". 

Any ideas about the problem? Is it our modem? Is it our pabx that
terminates the call?


thanks,
regards,

Nils


____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null