HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: [hylafax-users] spead




>
>
> > I've used RedHat 7, HylaFAX 4.1beta3, and a Cirrus Logic modem in Class
1
> > to send about 50 faxes in as many minutes.
> >
> > How many failures are you experiencing out of the 100?
>
>
>
 very few if any mostly no carrier detected or busy signal
 here is my modem config file I had problems setting it up
 and from trial and error got this to work .

 thanks for your help
 Dan

>
>
> #
> # Generic Class 1 modem configuration.
> #
> # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
> #
> CountryCode:  1
> AreaCode:  214
> FAXNumber:  ""
> LongDistancePrefix: 1
> InternationalPrefix: 011
> DialStringRules: etc/dialrules
> ServerTracing:  0xFFF
> SessionTracing:  0xFFF
> RecvFileMode:  0666
> LogFileMode:  0600
> DeviceMode:  0600
> RingsBeforeAnswer: 1
> SpeakerVolume:  quiet
> GettyArgs:  "-h %l dx_%s"
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType:  Class1  # use this to supply a hint
> ModemRate:  19200  # rate for DCE-DTE communication
> ModemFlowControl: xonxoff  # XON/XOFF flow control assumed
> #
> #ModemSetupDTRCmd: AT&D2  # setup so DTR drop resets modem
> #ModemSetupDCDCmd: AT&C1  # setup so DCD follows carrier
> ##GettyArgs:  "-h %l dx_%s" # modem must auto-detect fax/data
> #
> # We normally append the "@" symbol to the dial string so that
> # the modem will wait 5 seconds before attempting to connect
> # and return result codes that distinguish between no carrier
> # and no answer.  This makes it possible to avoid problems with
> # repeatedly dialing a number that doesn't have a fax machine
> # (kudos to Stuart Lynne for this trick.)
> #
> # NB: If you need to prefix phone numbers to get through a PBX,
> #     put it in the ModemDialCmd; e.g. "DT9%s@".
> #
> ModemDialCmd:  ATDT%s  # T for tone dialing, @ for silence
> #
> # Other possible configuration stuff.  The default strings are
> # shown below.  Only those that are different from the defaults
> # need to be included in the configuration file.
> #
> ###ModemResetCmds:  ""  # stuff to do when modem is reset
> ModemAnswerCmd:  ATA  # use this to answer phone
> #ModemNoFlowCmd:  AT&K  # disable flow control cmd
> #ModemHardFlowCmd: AT&K3  # hardware flow control cmd
> ModemSoftFlowCmd: AT&K4  # software flow control cmd
> ModemNoAutoAnswerCmd: ATS0=0  # disable auto-answer
> #
> # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
> # Note that we both turn the speaker on/off and set volume.
> #
> #ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
> #ModemEchoOffCmd: ATE0  # disable command echo
> #ModemVerboseResultsCmd: ATV1  # enable verbose command results
> #ModemResultCodesCmd: ATQ0  # enable result codes
> #ModemOnHookCmd:  ATH0  # place phone on hook (hangup)
> #ModemSoftResetCmd: ATZ  # do soft reset of modem
> #ModemWaitTimeCmd: ATS7=60  # wait 60 seconds for carrier
> #ModemCommaPauseTimeCmd: ATS8=2  # comma pause time is 2 seconds
> # ModemRecvFillOrder: LSB2MSB  # bit order of received facsimile
> #ModemSendFillOrder: LSB2MSB  # bit order modem expects for transmit
> #
> Class1Cmd:  AT+FCLASS=1 # command to enter class 1
> Class1TCFResponseDelay: 75  # 75ms delay between recv TCF & response
> Class1SendPPMDelay: 75  # 75ms delay before sending PPM
> Class1SendTCFDelay: 75  # 75ms delay between sending DCS & TCF
> Class1TrainingRecovery: 1500  # 1.5sec delay after training failure
> Class1RecvAbortOK: 200  # wait 200ms for abort response
> Class1FrameOverhead: 4  # 4 byte overhead in recvd HDLC frames
> Class1RecvIdentTimer: 40000  # 35+5secs waiting for ident frames
> Class1TCFMaxNonZero: 10  # max 10% of data may be non-zero
> Class1TCFMinRun: 1000  # min run is 2/3rds of TCF duration
>
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List
_______________________
>  To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org <
/dev/null
>
>



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null




Project hosted by iFAX Solutions