 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] AW: beta 3 and Cirrus chipset
- To: "Paul van der Vlis" <paul@vandervlis.nl>, <hylafax-users@hylafax.org>
- Subject: [hylafax-users] AW: beta 3 and Cirrus chipset
- From: "Bernd Proissl" <lists@proissl.de>
- Reply-To: <lists@proissl.de>
- Date: Mon, 26 Mar 2001 22:15:50 +0200
You may try to post your log on hylafax-devel to see what Harald Pollak has to say about it. Bernd > -----Urspr�ngliche Nachricht----- > Von: root@tosh.vandervlis.nl [mailto:root@tosh.vandervlis.nl]Im Auftrag > von Paul van der Vlis > Gesendet am: Montag, 26. M�rz 2001 21:58 > An: hylafax-users@hylafax.org > Betreff: [hylafax-users] beta 3 and Cirrus chipset > > Hello! > > Nice to see that there is a new Hylafax version! > > I am using a Best 3314VH internal 33k6 modem with Cirrus chipset > (faxclass 1) and the new beta3 of Hylafax for a customer, but I see the > following problem while sending a fax: > > The fax is send, an EOP is send, but no responce from the other side, a > timeout follows. This happens 3 times, then the session ends, but > Hylafax thinks the fax was not send OK, so after some time Hylafax tries > again... > > Bye, > Paul van der Vlis > > Mar 26 17:31:40.19: [ 1338]: SESSION BEGIN 00000003 31208738934 > Mar 26 17:31:40.21: [ 1338]: SEND FAX: JOB 1 DEST 020-8738934 COMMID > 00000003 > Mar 26 17:31:40.21: [ 1338]: DELAY 2600 ms > Mar 26 17:31:42.80: [ 1338]: <-- [4:ATZ\r] > Mar 26 17:31:42.96: [ 1338]: --> [3:ATZ] > Mar 26 17:31:42.96: [ 1338]: --> [2:OK] > Mar 26 17:31:42.96: [ 1338]: <-- [15:ATE0V1Q0S0=0H0\r] > Mar 26 17:31:45.14: [ 1338]: --> [14:ATE0V1Q0S0=0H0] > Mar 26 17:31:45.14: [ 1338]: --> [2:OK] > Mar 26 17:31:45.14: [ 1338]: <-- [21:ATS8=2S7=60\Q3&D3&C1\r] > Mar 26 17:31:45.22: [ 1338]: --> [2:OK] > Mar 26 17:31:45.22: [ 1338]: <-- [12:AT+FCLASS=1\r] > Mar 26 17:31:45.29: [ 1338]: --> [2:OK] > Mar 26 17:31:45.29: [ 1338]: <-- [5:ATM0\r] > Mar 26 17:31:45.35: [ 1338]: --> [2:OK] > Mar 26 17:31:45.35: [ 1338]: <-- [12:AT+FCLASS=1\r] > Mar 26 17:31:45.52: [ 1338]: --> [2:OK] > Mar 26 17:31:45.52: [ 1338]: DIAL 0208738934 > Mar 26 17:31:45.52: [ 1338]: <-- [15:ATDT0208738934\r] > Mar 26 17:32:01.13: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:02.62: [ 1338]: --> [2:OK] > Mar 26 17:32:02.62: [ 1338]: REMOTE CSI "31208738934" > Mar 26 17:32:02.62: [ 1338]: <-- [9:AT+FRH=3\r] > Mar 26 17:32:02.65: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:02.90: [ 1338]: --> [2:OK] > Mar 26 17:32:02.90: [ 1338]: REMOTE best rate 14400 bit/s > Mar 26 17:32:02.90: [ 1338]: REMOTE max page width 1728 pixels in 215 mm > Mar 26 17:32:02.90: [ 1338]: REMOTE max unlimited page length > Mar 26 17:32:02.90: [ 1338]: REMOTE best vres 7.7 line/mm > Mar 26 17:32:02.90: [ 1338]: REMOTE best format 2-D MMR > Mar 26 17:32:02.90: [ 1338]: REMOTE supports T.30 Annex A, ECM > Mar 26 17:32:02.90: [ 1338]: REMOTE best 0 ms/scanline > Mar 26 17:32:02.90: [ 1338]: USE 14400 bit/s > Mar 26 17:32:02.90: [ 1338]: USE 0 ms/scanline > Mar 26 17:32:02.90: [ 1338]: SEND file "docq/doc1.cover;00" > Mar 26 17:32:02.90: [ 1338]: USE page width 1728 pixels in 215 mm > Mar 26 17:32:02.90: [ 1338]: USE unlimited page length > Mar 26 17:32:02.90: [ 1338]: USE 3.85 line/mm > Mar 26 17:32:02.90: [ 1338]: USE 1-D MR > Mar 26 17:32:02.90: [ 1338]: SEND training at v.17 14400 bit/s > Mar 26 17:32:02.90: [ 1338]: <-- [9:AT+FTH=3\r] > Mar 26 17:32:03.03: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:03.03: [ 1338]: <-- data [23] > Mar 26 17:32:03.03: [ 1338]: <-- data [2] > Mar 26 17:32:04.27: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:04.27: [ 1338]: <-- data [6] > Mar 26 17:32:04.27: [ 1338]: <-- data [2] > Mar 26 17:32:04.61: [ 1338]: --> [2:OK] > Mar 26 17:32:04.61: [ 1338]: DELAY 75 ms > Mar 26 17:32:04.69: [ 1338]: <-- [11:AT+FTM=145\r] > Mar 26 17:32:04.83: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:04.83: [ 1338]: <-- data [1024] > Mar 26 17:32:04.83: [ 1338]: <-- data [1024] > Mar 26 17:32:04.83: [ 1338]: <-- data [652] > Mar 26 17:32:04.83: [ 1338]: <-- data [2] > Mar 26 17:32:07.97: [ 1338]: --> [2:OK] > Mar 26 17:32:07.97: [ 1338]: <-- [9:AT+FRH=3\r] > Mar 26 17:32:08.14: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:09.73: [ 1338]: --> [2:OK] > Mar 26 17:32:09.73: [ 1338]: REMOTE CSI "31208738934" > Mar 26 17:32:09.73: [ 1338]: <-- [9:AT+FRH=3\r] > Mar 26 17:32:09.76: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:10.02: [ 1338]: --> [2:OK] > Mar 26 17:32:10.02: [ 1338]: SEND training at v.29 9600 bit/s > Mar 26 17:32:10.02: [ 1338]: <-- [9:AT+FTH=3\r] > Mar 26 17:32:10.15: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:10.15: [ 1338]: <-- data [23] > Mar 26 17:32:10.15: [ 1338]: <-- data [2] > Mar 26 17:32:11.39: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:11.39: [ 1338]: <-- data [6] > Mar 26 17:32:11.39: [ 1338]: <-- data [2] > Mar 26 17:32:11.73: [ 1338]: --> [2:OK] > Mar 26 17:32:11.73: [ 1338]: DELAY 75 ms > Mar 26 17:32:11.81: [ 1338]: <-- [10:AT+FTM=96\r] > Mar 26 17:32:11.94: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:11.94: [ 1338]: <-- data [1024] > Mar 26 17:32:11.94: [ 1338]: <-- data [776] > Mar 26 17:32:11.94: [ 1338]: <-- data [2] > Mar 26 17:32:13.73: [ 1338]: --> [2:OK] > Mar 26 17:32:13.73: [ 1338]: <-- [9:AT+FRH=3\r] > Mar 26 17:32:13.89: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:14.95: [ 1338]: --> [2:OK] > Mar 26 17:32:14.95: [ 1338]: TRAINING succeeded > Mar 26 17:32:14.95: [ 1338]: <-- [10:AT+FTM=96\r] > Mar 26 17:32:15.08: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:15.08: [ 1338]: SEND begin page > Mar 26 17:32:15.08: [ 1338]: <-- data [1028] > Mar 26 17:32:15.08: [ 1338]: <-- data [1024] > Mar 26 17:32:15.08: [ 1338]: <-- data [1028] > Mar 26 17:32:15.08: [ 1338]: <-- data [1025] > Mar 26 17:32:15.09: [ 1338]: <-- data [1028] > Mar 26 17:32:15.63: [ 1338]: <-- data [1029] > Mar 26 17:32:16.43: [ 1338]: <-- data [1025] > Mar 26 17:32:17.36: [ 1338]: <-- data [1024] > Mar 26 17:32:18.16: [ 1338]: <-- data [1024] > Mar 26 17:32:18.96: [ 1338]: <-- data [1024] > Mar 26 17:32:19.90: [ 1338]: <-- data [1024] > Mar 26 17:32:20.70: [ 1338]: <-- data [921] > Mar 26 17:32:21.50: [ 1338]: SENT 12183 bytes of data > Mar 26 17:32:21.50: [ 1338]: SEND 2D RTC > Mar 26 17:32:21.50: [ 1338]: <-- data [30] > Mar 26 17:32:21.50: [ 1338]: <-- data [2] > Mar 26 17:32:21.50: [ 1338]: SEND end page > Mar 26 17:32:25.55: [ 1338]: --> [2:OK] > Mar 26 17:32:25.55: [ 1338]: DELAY 95 ms > Mar 26 17:32:25.65: [ 1338]: SEND send EOP (no more pages or documents) > Mar 26 17:32:25.65: [ 1338]: <-- [9:AT+FTH=3\r] > Mar 26 17:32:25.78: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:25.78: [ 1338]: <-- data [3] > Mar 26 17:32:25.78: [ 1338]: <-- data [2] > Mar 26 17:32:26.52: [ 1338]: --> [2:OK] > Mar 26 17:32:26.52: [ 1338]: <-- [9:AT+FRH=3\r] > Mar 26 17:32:26.69: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:27.74: [ 1338]: --> [2:OK] > Mar 26 17:32:27.74: [ 1338]: SEND recv RTN (retrain negative) > Mar 26 17:32:27.74: [ 1338]: SEND training at v.29 7200 bit/s > Mar 26 17:32:27.74: [ 1338]: <-- [9:AT+FTH=3\r] > Mar 26 17:32:27.87: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:27.87: [ 1338]: <-- data [23] > Mar 26 17:32:27.87: [ 1338]: <-- data [2] > Mar 26 17:32:29.11: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:29.11: [ 1338]: <-- data [6] > Mar 26 17:32:29.11: [ 1338]: <-- data [2] > Mar 26 17:32:29.45: [ 1338]: --> [2:OK] > Mar 26 17:32:29.45: [ 1338]: DELAY 75 ms > Mar 26 17:32:29.53: [ 1338]: <-- [10:AT+FTM=72\r] > Mar 26 17:32:29.66: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:29.66: [ 1338]: <-- data [1024] > Mar 26 17:32:29.66: [ 1338]: <-- data [326] > Mar 26 17:32:29.66: [ 1338]: <-- data [2] > Mar 26 17:32:31.45: [ 1338]: --> [2:OK] > Mar 26 17:32:31.45: [ 1338]: <-- [9:AT+FRH=3\r] > Mar 26 17:32:31.61: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:32.67: [ 1338]: --> [2:OK] > Mar 26 17:32:32.67: [ 1338]: TRAINING succeeded > Mar 26 17:32:32.67: [ 1338]: <-- [10:AT+FTM=72\r] > Mar 26 17:32:32.80: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:32.80: [ 1338]: SEND begin page > Mar 26 17:32:32.80: [ 1338]: <-- data [1028] > Mar 26 17:32:32.80: [ 1338]: <-- data [1026] > Mar 26 17:32:32.80: [ 1338]: <-- data [1028] > Mar 26 17:32:32.80: [ 1338]: <-- data [1025] > Mar 26 17:32:32.80: [ 1338]: <-- data [1028] > Mar 26 17:32:33.45: [ 1338]: <-- data [1029] > Mar 26 17:32:34.51: [ 1338]: <-- data [1025] > Mar 26 17:32:35.76: [ 1338]: <-- data [1024] > Mar 26 17:32:36.82: [ 1338]: <-- data [1024] > Mar 26 17:32:37.89: [ 1338]: <-- data [1024] > Mar 26 17:32:39.14: [ 1338]: <-- data [1024] > Mar 26 17:32:40.20: [ 1338]: <-- data [924] > Mar 26 17:32:41.27: [ 1338]: SENT 12186 bytes of data > Mar 26 17:32:41.27: [ 1338]: SEND 2D RTC > Mar 26 17:32:41.27: [ 1338]: <-- data [30] > Mar 26 17:32:41.27: [ 1338]: <-- data [2] > Mar 26 17:32:41.27: [ 1338]: SEND end page > Mar 26 17:32:46.66: [ 1338]: --> [2:OK] > Mar 26 17:32:46.66: [ 1338]: DELAY 95 ms > Mar 26 17:32:46.76: [ 1338]: SEND send EOP (no more pages or documents) > Mar 26 17:32:46.76: [ 1338]: <-- [9:AT+FTH=3\r] > Mar 26 17:32:46.89: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:46.89: [ 1338]: <-- data [3] > Mar 26 17:32:46.89: [ 1338]: <-- data [2] > Mar 26 17:32:47.63: [ 1338]: --> [2:OK] > Mar 26 17:32:47.63: [ 1338]: <-- [9:AT+FRH=3\r] > Mar 26 17:32:47.67: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:52.67: [ 1338]: <-- data [1] > Mar 26 17:32:52.87: [ 1338]: MODEM <Timeout> > Mar 26 17:32:52.87: [ 1338]: SEND send EOP (no more pages or documents) > Mar 26 17:32:52.87: [ 1338]: <-- [9:AT+FTH=3\r] > Mar 26 17:32:53.00: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:53.00: [ 1338]: <-- data [3] > Mar 26 17:32:53.00: [ 1338]: <-- data [2] > Mar 26 17:32:53.75: [ 1338]: --> [2:OK] > Mar 26 17:32:53.75: [ 1338]: <-- [9:AT+FRH=3\r] > Mar 26 17:32:53.85: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:58.85: [ 1338]: <-- data [1] > Mar 26 17:32:59.05: [ 1338]: MODEM <Timeout> > Mar 26 17:32:59.05: [ 1338]: SEND send EOP (no more pages or documents) > Mar 26 17:32:59.05: [ 1338]: <-- [9:AT+FTH=3\r] > Mar 26 17:32:59.18: [ 1338]: --> [7:CONNECT] > Mar 26 17:32:59.18: [ 1338]: <-- data [3] > Mar 26 17:32:59.18: [ 1338]: <-- data [2] > Mar 26 17:32:59.93: [ 1338]: --> [2:OK] > Mar 26 17:32:59.93: [ 1338]: <-- [9:AT+FRH=3\r] > Mar 26 17:33:00.10: [ 1338]: --> [7:CONNECT] > Mar 26 17:33:05.10: [ 1338]: <-- data [1] > Mar 26 17:33:05.30: [ 1338]: MODEM <Timeout> > Mar 26 17:33:05.30: [ 1338]: No response to MPS or EOP repeated 3 tries > Mar 26 17:33:05.30: [ 1338]: <-- [9:AT+FTH=3\r] > Mar 26 17:33:05.43: [ 1338]: --> [7:CONNECT] > Mar 26 17:33:05.43: [ 1338]: <-- data [3] > Mar 26 17:33:05.43: [ 1338]: <-- data [2] > Mar 26 17:33:06.18: [ 1338]: --> [2:OK] > Mar 26 17:33:06.18: [ 1338]: <-- [5:ATH0\r] > Mar 26 17:33:08.32: [ 1338]: --> [2:OK] > Mar 26 17:33:08.32: [ 1338]: SESSION END > > > ____________________ HylaFAX(tm) Users Mailing List _______________________ > To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null > ____________________ HylaFAX(tm) Users Mailing List _______________________ To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
- References:
- [hylafax-users] beta 3 and Cirrus chipset
- From: Paul van der Vlis <paul@vandervlis.nl>
- [hylafax-users] beta 3 and Cirrus chipset
- Prev by Date: [hylafax-users] AW: Local fax cannot send by HylaFax
- Next by Date: Re: [hylafax-users] doneq files question
- Prev by thread: Re: [hylafax-users] beta 3 and Cirrus chipset
- Next by thread: [hylafax-users] installing viewer for redhat
- Index(es):
Project hosted by iFAX Solutions