 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] No response to MPS again
- To: <hylafax-users@hylafax.org>, <hylafax-devel@hylafax.org>
- Subject: [hylafax-users] No response to MPS again
- From: "LAZAR Imre" <imre@transorg.hu>
- Date: Mon, 26 Mar 2001 09:14:39 +0200
Haho, I sent a fax to myself, with the newest CVS. The sender is a Class1 Rockwell. The receiver is a ZyXEL Omni288S Class2.0. It can be reproduce any time. Imre. The sender.conf: ModemType: Class1 # use this to supply a hint ModemRate: 38400 # rate for DCE-DTE communication ModemFlowControl: rtscts # default ModemNoFlowCmd: AT&K0 # setup no flow control ModemHardFlowCmd: AT&K3 # setup hardware flow control ModemSoftFlowCmd: AT&K4 # setup software flow control ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) ModemMfrQueryCmd: !Rockwell ModemModelQueryCmd: !RC288DPi ModemRevQueryCmd: ATI3 # product information ModemDialCmd: ATDT%s # T for tone dialing The sendlog: Mar 25 14:57:25.14: [11077]: SESSION BEGIN 00030921 36103472020 Mar 25 14:57:25.14: [11077]: SEND FAX: JOB 13738 DEST 03472020 COMMID 00030921 Mar 25 14:57:25.14: [11077]: MODEM set DTR OFF Mar 25 14:57:25.14: [11077]: DELAY 2600 ms Mar 25 14:57:27.74: [11077]: MODEM set DTR ON Mar 25 14:57:27.74: [11077]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS Mar 25 14:57:27.74: [11077]: MODEM flush i/o Mar 25 14:57:27.74: [11077]: <-- [4:ATZ\r] Mar 25 14:57:27.87: [11077]: --> [2:OK] Mar 25 14:57:27.87: [11077]: <-- [15:ATE0V1Q0S0=0H0\r] Mar 25 14:57:27.88: [11077]: --> [14:ATE0V1Q0S0=0H0] Mar 25 14:57:27.88: [11077]: --> [2:OK] Mar 25 14:57:27.88: [11077]: <-- [21:ATS8=2S7=60&K3&D2&C1\r] Mar 25 14:57:27.90: [11077]: --> [2:OK] Mar 25 14:57:27.90: [11077]: <-- [12:AT+FCLASS=1\r] Mar 25 14:57:27.91: [11077]: --> [2:OK] Mar 25 14:57:27.91: [11077]: <-- [5:ATM0\r] Mar 25 14:57:27.92: [11077]: --> [2:OK] Mar 25 14:57:27.92: [11077]: STATE CHANGE: RUNNING -> SENDING Mar 25 14:57:27.92: [11077]: MODEM input buffering enabled Mar 25 14:57:27.92: [11077]: Apply DialString rules to "03472020" Mar 25 14:57:27.92: [11077]: --> return result "03472020" Mar 25 14:57:27.92: [11077]: <-- [12:AT+FCLASS=1\r] Mar 25 14:57:28.03: [11077]: --> [2:OK] Mar 25 14:57:28.06: [11077]: DIAL 03472020 Mar 25 14:57:28.06: [11077]: <-- [13:ATDT03472020\r] Mar 25 14:57:45.66: [11077]: --> [7:CONNECT] Mar 25 14:57:45.66: [11077]: MODEM input buffering disabled Mar 25 14:57:47.02: [11077]: --> HDLC<25:FF C0 02 04 04 04 04 04 04 04 04 04 0C 4C 0C 4C EC 2C CC 8C 6C CC D4 43 F9> Mar 25 14:57:47.04: [11077]: --> [2:OK] Mar 25 14:57:47.04: [11077]: REMOTE CSI "+3613472020" Mar 25 14:57:47.04: [11077]: <-- [9:AT+FRH=3\r] Mar 25 14:57:47.05: [11077]: --> [7:CONNECT] Mar 25 14:57:47.29: [11077]: --> HDLC<9:FF C8 01 00 77 5F 00 F1 7A> Mar 25 14:57:47.30: [11077]: --> [2:OK] Mar 25 14:57:47.30: [11077]: REMOTE best rate 14400 bit/s Mar 25 14:57:47.30: [11077]: REMOTE max page width 2432 pixels in 303 mm Mar 25 14:57:47.30: [11077]: REMOTE max unlimited page length Mar 25 14:57:47.30: [11077]: REMOTE best vres 7.7 line/mm Mar 25 14:57:47.30: [11077]: REMOTE best format 2-D MR Mar 25 14:57:47.30: [11077]: REMOTE best 0 ms/scanline Mar 25 14:57:47.30: [11077]: USE 14400 bit/s Mar 25 14:57:47.30: [11077]: USE 0 ms/scanline Mar 25 14:57:47.30: [11077]: SEND file "docq/doc13740.ps;70" Mar 25 14:57:47.30: [11077]: USE page width 1728 pixels in 215 mm Mar 25 14:57:47.30: [11077]: USE unlimited page length Mar 25 14:57:47.30: [11077]: USE 3.85 line/mm Mar 25 14:57:47.30: [11077]: USE 2-D MR Mar 25 14:57:47.30: [11077]: SEND training at v.17 14400 bit/s Mar 25 14:57:47.30: [11077]: <-- [9:AT+FTH=3\r] Mar 25 14:57:47.35: [11077]: --> [7:CONNECT] Mar 25 14:57:47.35: [11077]: <-- HDLC<23:FF C0 C2 0C 4C 0C 4C EC 2C CC 8C 6C CC D4 04 04 04 04 04 04 04 04 04> Mar 25 14:57:47.35: [11077]: <-- data [23] Mar 25 14:57:47.35: [11077]: <-- data [2] Mar 25 14:57:49.14: [11077]: --> [7:CONNECT] Mar 25 14:57:49.14: [11077]: <-- HDLC<6:FF C8 C1 00 45 1E> Mar 25 14:57:49.14: [11077]: <-- data [6] Mar 25 14:57:49.14: [11077]: <-- data [2] Mar 25 14:57:49.57: [11077]: --> [2:OK] Mar 25 14:57:49.57: [11077]: DELAY 75 ms Mar 25 14:57:49.65: [11077]: <-- [11:AT+FTM=145\r] Mar 25 14:57:49.68: [11077]: --> [7:CONNECT] Mar 25 14:57:49.68: [11077]: <-- data [1024] Mar 25 14:57:49.68: [11077]: <-- data [1024] Mar 25 14:57:49.68: [11077]: <-- data [652] Mar 25 14:57:49.68: [11077]: <-- data [2] Mar 25 14:57:52.80: [11077]: --> [2:OK] Mar 25 14:57:52.80: [11077]: <-- [9:AT+FRH=3\r] Mar 25 14:57:54.22: [11077]: --> [7:CONNECT] Mar 25 14:57:55.11: [11077]: --> HDLC<5:FF C8 21 57 BE> Mar 25 14:57:55.12: [11077]: --> [2:OK] Mar 25 14:57:55.12: [11077]: TRAINING succeeded Mar 25 14:57:55.12: [11077]: <-- [11:AT+FTM=146\r] Mar 25 14:57:55.15: [11077]: --> [7:CONNECT] Mar 25 14:57:55.15: [11077]: SEND begin page Mar 25 14:57:55.15: [11077]: <-- data [953] Mar 25 14:57:55.15: [11077]: SENT 948 bytes of data Mar 25 14:57:55.15: [11077]: SEND 2D RTC Mar 25 14:57:55.15: [11077]: <-- data [30] Mar 25 14:57:55.16: [11077]: <-- data [2] Mar 25 14:57:55.16: [11077]: SEND end page Mar 25 14:57:56.06: [11077]: --> [2:OK] Mar 25 14:57:56.06: [11077]: DELAY 95 ms Mar 25 14:57:56.16: [11077]: SEND send EOP (no more pages or documents) Mar 25 14:57:56.16: [11077]: <-- [9:AT+FTH=3\r] Mar 25 14:57:56.21: [11077]: --> [7:CONNECT] Mar 25 14:57:56.21: [11077]: <-- HDLC<3:FF C8 F4> Mar 25 14:57:56.21: [11077]: <-- data [3] Mar 25 14:57:56.21: [11077]: <-- data [2] Mar 25 14:57:57.53: [11077]: --> [2:OK] Mar 25 14:57:57.53: [11077]: <-- [9:AT+FRH=3\r] Mar 25 14:58:00.63: [11077]: --> [0:] Mar 25 14:58:00.63: [11077]: MODEM <Empty line> Mar 25 14:58:00.63: [11077]: MODEM TIMEOUT: waiting for v.21 carrier Mar 25 14:58:00.63: [11077]: <-- data [1] Mar 25 14:58:00.69: [11077]: --> [2:OK] Mar 25 14:58:00.69: [11077]: SEND send EOP (no more pages or documents) Mar 25 14:58:00.69: [11077]: <-- [9:AT+FTH=3\r] Mar 25 14:58:00.74: [11077]: --> [7:CONNECT] Mar 25 14:58:00.74: [11077]: <-- HDLC<3:FF C8 F4> Mar 25 14:58:00.74: [11077]: <-- data [3] Mar 25 14:58:00.74: [11077]: <-- data [2] Mar 25 14:58:02.06: [11077]: --> [2:OK] Mar 25 14:58:02.06: [11077]: <-- [9:AT+FRH=3\r] Mar 25 14:58:05.16: [11077]: --> [0:] Mar 25 14:58:05.16: [11077]: MODEM <Empty line> Mar 25 14:58:05.16: [11077]: MODEM TIMEOUT: waiting for v.21 carrier Mar 25 14:58:05.16: [11077]: <-- data [1] Mar 25 14:58:05.22: [11077]: --> [2:OK] Mar 25 14:58:05.22: [11077]: SEND send EOP (no more pages or documents) Mar 25 14:58:05.22: [11077]: <-- [9:AT+FTH=3\r] Mar 25 14:58:05.27: [11077]: --> [7:CONNECT] Mar 25 14:58:05.27: [11077]: <-- HDLC<3:FF C8 F4> Mar 25 14:58:05.27: [11077]: <-- data [3] Mar 25 14:58:05.27: [11077]: <-- data [2] Mar 25 14:58:06.59: [11077]: --> [2:OK] Mar 25 14:58:06.59: [11077]: <-- [9:AT+FRH=3\r] Mar 25 14:58:09.69: [11077]: --> [0:] Mar 25 14:58:09.69: [11077]: MODEM <Empty line> Mar 25 14:58:09.69: [11077]: MODEM TIMEOUT: waiting for v.21 carrier Mar 25 14:58:09.69: [11077]: <-- data [1] Mar 25 14:58:09.75: [11077]: --> [2:OK] Mar 25 14:58:09.75: [11077]: No response to MPS or EOP repeated 3 tries Mar 25 14:58:09.75: [11077]: <-- [9:AT+FTH=3\r] Mar 25 14:58:09.80: [11077]: --> [7:CONNECT] Mar 25 14:58:09.80: [11077]: <-- HDLC<3:FF C8 DF> Mar 25 14:58:09.80: [11077]: <-- data [3] Mar 25 14:58:09.80: [11077]: <-- data [2] Mar 25 14:58:11.12: [11077]: --> [2:OK] Mar 25 14:58:11.12: [11077]: MODEM input buffering enabled Mar 25 14:58:11.12: [11077]: <-- [5:ATH0\r] Mar 25 14:58:13.05: [11077]: --> [2:OK] Mar 25 14:58:13.05: [11077]: MODEM set DTR OFF Mar 25 14:58:13.05: [11077]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5) Mar 25 14:58:13.05: [11077]: SESSION END The Receiver.conf: ModemType: Class2.0 # use class 2.0 interface ModemRate: 38400 # 38.4 works fine ModemFlowControl: rtscts # default ModemNoFlowCmd: AT&H0 # disable flow control ModemHardFlowCmd: AT&H3 # hardware flow control ModemSoftFlowCmd: AT&H4 # software flow control ModemSetupDTRCmd: AT&D2 # DTR off causes modem to hang up ModemSetupDCDCmd: AT&C1 # DCD tracks carrier ModemSetupAACmd: AT+FAA=1 # enable in current class # Additional reset commands: # &B1 DTE-DCE rate is fixed at DTE setting # &N0 Auto-negotiate highest possible DCE-DCE link rate # &S0 DSR always on # *F0 Deny remote configuration # (actually *F0 doesn't work in the firmware -- sigh) # S18=4 Receive at 38400 # S38.3=1 DCD on/off sequence follows UNIX standard; also # fix receiving baud rate at S18 value # ModemResetCmds: AT&B1&N0&S0S18=4S38.3=1 ModemDialCmd: ATDT%s # no '@' 'cuz then busy not recognized NoCarrierRetrys: 3 # retry 3 times on no carrier ModemSetVolumeCmd: "ATM0 ATM1L1 ATM1L3 ATM1L5 ATM1L7" # # Caller ID configuration setup. # #QualifyCID: etc/cid # CID access control list file #CIDNumber: "CALLER NUMBER: " # pattern string for phone number info #CIDName: "CALLER NAME: " # pattern string for identity info PagerSetupCmds: AT&K0&N15 # use V.22 at 1200 bps (PageNet) The Receive log: Mar 25 14:57:33.81: [10212]: SESSION BEGIN 00030922 3613472020 Mar 25 14:57:33.81: [10212]: <-- [4:ATA\r] Mar 25 14:57:49.63: [10212]: --> [4:+FCO] Mar 25 14:57:49.65: [10212]: ANSWER: FAX CONNECTION Mar 25 14:57:49.65: [10212]: STATE CHANGE: ANSWERING -> RECEIVING Mar 25 14:57:49.66: [10212]: MODEM input buffering enabled Mar 25 14:57:49.66: [10212]: RECV FAX: begin Mar 25 14:57:53.63: [10212]: --> [28:+FTI:" +3613472020" ] Mar 25 14:57:53.63: [10212]: REMOTE TSI "+3613472020" Mar 25 14:57:53.63: [10212]: --> [20:+FCS:0,5,0,2,1,0,0,0] Mar 25 14:57:53.63: [10212]: REMOTE wants 14400 bit/s Mar 25 14:57:53.63: [10212]: REMOTE wants page width 1728 pixels in 215 mm Mar 25 14:57:53.63: [10212]: REMOTE wants unlimited page length Mar 25 14:57:53.63: [10212]: REMOTE wants 3.85 line/mm Mar 25 14:57:53.63: [10212]: REMOTE wants 2-D MR Mar 25 14:57:53.63: [10212]: --> [2:OK] Mar 25 14:57:53.66: [10212]: <-- [7:AT+FDR\r] Mar 25 14:57:55.22: [10212]: --> [20:+FCS:0,5,0,2,1,0,0,0] Mar 25 14:57:55.22: [10212]: REMOTE wants 14400 bit/s Mar 25 14:57:55.22: [10212]: REMOTE wants page width 1728 pixels in 215 mm Mar 25 14:57:55.22: [10212]: REMOTE wants unlimited page length Mar 25 14:57:55.22: [10212]: REMOTE wants 3.85 line/mm Mar 25 14:57:55.22: [10212]: REMOTE wants 2-D MR Mar 25 14:57:55.62: [10212]: --> [7:CONNECT] Mar 25 14:57:55.62: [10212]: RECV: begin page Mar 25 14:57:55.62: [10212]: RECV: send trigger 022 Mar 25 14:57:55.62: [10212]: <-- data [1] Mar 25 14:57:55.79: [10212]: RECV/CQ: Bad 1D pixel count, row 10, got 1737, expected 1728 Mar 25 14:57:56.05: [10212]: RECV/CQ: Bad 1D pixel count, row 99, got 0, expected 1728 Mar 25 14:57:56.05: [10212]: RECV/CQ: Bad 1D pixel count, row 100, got 0, expected 1728 Mar 25 14:57:56.05: [10212]: RECV/CQ: Bad 1D pixel count, row 101, got 0, expected 1728 Mar 25 14:57:56.05: [10212]: RECV/CQ: Bad 1D pixel count, row 102, got 0, expected 1728 Mar 25 14:57:56.16: [10212]: RECV/CQ: Bad 1D pixel count, row 103, got 0, expected 1728 Mar 25 14:57:56.16: [10212]: RECV: 1039 bytes of data, 104 total lines Mar 25 14:57:56.16: [10212]: --> [15:+FPS:2,63,0,0,0] Mar 25 14:57:56.16: [10212]: --> [7:+FHS:91] Mar 25 14:57:56.18: [10212]: REMOTE HANGUP: Missing EOL after 5 seconds (section 3.2/T.4) (code 91) Mar 25 14:57:56.18: [10212]: --> [5:ERROR] Mar 25 14:57:56.19: [10212]: RECV FAX (00030922): recvq/fax09692.tif from +3613472020, route to <unspecified>, 0 pages in 0:07 Mar 25 14:57:56.19: [10212]: RECV FAX: Missing EOL after 5 seconds (section 3.2/T.4) Mar 25 14:57:56.19: [10212]: RECV FAX (00030922): session with +3613472020 terminated abnormally: Missing EOL after 5 seconds Mar 25 14:57:56.19: [10212]: RECV FAX: bin/faxrcvd "recvq/fax09692.tif" "ttyM2" "00030922" "Missing EOL after 5 seconds (secti Mar 25 14:57:56.62: [10212]: RECV FAX: end Mar 25 14:57:56.63: [10212]: SESSION END ____________________ HylaFAX(tm) Users Mailing List _______________________ To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
- Follow-Ups:
- Re: [hylafax-users] [hylafax-devel] No response to MPS again
- From: "Vyacheslav Frolov" <v.frolov@globalone.ru>
- Re: [hylafax-users] [hylafax-devel] No response to MPS again
- Prev by Date: Re: [hylafax-users] E-mail confirmation problem,
- Next by Date: [hylafax-users] Phase B code 70
- Prev by thread: Re: [hylafax-users] E-mail confirmation problem,
- Next by thread: Re: [hylafax-users] [hylafax-devel] No response to MPS again
- Index(es):
Project hosted by iFAX Solutions