[hylafax-users] No response to MPS repeated 3 times

["Work" <dmercer@stratcom.ca>]

I have also attached the modem configuration file ( the modem is a Netaccess
4 port card MPM-4).  Sending seems to mostly work but will always fail
sending to this machine with the same error...any ideas would be greatly
appreciated

I am running the new version on rh7




Your facsimile job to 6812025 failed because:
    No response to MPS repeated 3 times; Giving up after 3 attempts to send
same page

    ---- Transcript of session follows ----

Feb 27 19:04:45.61: [ 2095]: SESSION BEGIN 00000341 16046812025
Feb 27 19:04:45.61: [ 2095]: SEND FAX: JOB 176 DEST 6812025 COMMID 00000341
Feb 27 19:04:45.61: [ 2095]: DELAY 2600 ms
Feb 27 19:04:48.21: [ 2095]: <-- [4:ATZ\r]
Feb 27 19:04:48.34: [ 2095]: --> [2:OK]
Feb 27 19:04:48.34: [ 2095]: <-- [15:ATE0V1Q0S0=0H0\r]
Feb 27 19:04:48.87: [ 2095]: --> [14:ATE0V1Q0S0=0H0]
Feb 27 19:04:48.87: [ 2095]: --> [2:OK]
Feb 27 19:04:48.87: [ 2095]: <-- [12:ATS8=2S7=60\r]
Feb 27 19:04:49.03: [ 2095]: --> [2:OK]
Feb 27 19:04:49.03: [ 2095]: <-- [12:AT+FCLASS=2\r]
Feb 27 19:04:49.19: [ 2095]: --> [2:OK]
Feb 27 19:04:49.19: [ 2095]: <-- [10:AT+FTBC=0\r]
Feb 27 19:04:49.34: [ 2095]: --> [2:OK]
Feb 27 19:04:49.34: [ 2095]: <-- [10:AT+FBOR=0\r]
Feb 27 19:04:49.49: [ 2095]: --> [2:OK]
Feb 27 19:04:49.49: [ 2095]: <-- [13:AT+FPHCTO=30\r]
Feb 27 19:04:49.65: [ 2095]: --> [2:OK]
Feb 27 19:04:49.65: [ 2095]: <-- [24:AT+FDCC=1,5,2,2,3,0,0,0\r]
Feb 27 19:04:49.83: [ 2095]: --> [2:OK]
Feb 27 19:04:49.83: [ 2095]: <-- [5:ATM0\r]5616730646
Feb 27 19:04:49.98: [ 2095]: --> [2:OK]
Feb 27 19:04:49.99: [ 2095]: <-- [12:AT+FCLASS=2\r]
Feb 27 19:04:50.24: [ 2095]: --> [2:OK]
Feb 27 19:04:50.24: [ 2095]: <-- [10:AT+FTBC=0\r]
Feb 27 19:04:50.49: [ 2095]: --> [2:OK]
Feb 27 19:04:50.49: [ 2095]: <-- [10:AT+FBOR=0\r]
Feb 27 19:04:50.74: [ 2095]: --> [2:OK]
Feb 27 19:04:50.74: [ 2095]: <-- [13:AT+FPHCTO=30\r]
Feb 27 19:04:51.00: [ 2095]: --> [2:OK]
Feb 27 19:04:51.00: [ 2095]: <-- [24:AT+FDCC=1,5,2,2,3,0,0,0\r]
Feb 27 19:04:51.28: [ 2095]: --> [2:OK]
Feb 27 19:04:51.28: [ 2095]: <-- [31:AT+FLID="Strategic Communicat"\r]
Feb 27 19:04:51.57: [ 2095]: --> [2:OK]
Feb 27 19:04:51.58: [ 2095]: DIAL 9,6812025
Feb 27 19:04:51.58: [ 2095]: <-- [14:ATDT9,6812025\r]
Feb 27 19:05:13.86: [ 2095]: --> [5:+FCON]
Feb 27 19:05:16.15: [ 2095]: --> [128:+FNSF:00 00 11 90 00 85 4D 10 53 54 52
41 54 43 4F 4D 20 56 41 4E 43 20 20 20 01 0E 00 3E 00 86 04 39 39 39 39 80
D8 09 02 01 00]
Feb 27 19:05:16.15: [ 2095]: REMOTE NSF "00 00 11 90 00 85 4D 10 53 54 52 41
54 43 4F 4D 20 56 41 4E 43 20 20 20 01 0E 00 3E 00 86 04 39 39 39 39 80 D8
09 02 01 00"
Feb 27 19:05:16.16: [ 2095]: NSF remote fax equipment: Canon
Feb 27 19:05:16.16: [ 2095]: NSF remote station ID: "STRATCOM VANC   "
Feb 27 19:05:16.94: [ 2095]: --> [28:+FCSI:"         604 6812025"]
Feb 27 19:05:16.94: [ 2095]: REMOTE CSI "604 6812025"
Feb 27 19:05:17.23: [ 2095]: --> [21:+FDIS:1,5,0,2,3,1,0,0]
Feb 27 19:05:17.23: [ 2095]: --> [2:OK]
Feb 27 19:05:17.24: [ 2095]: REMOTE best rate 14400 bit/s
Feb 27 19:05:17.24: [ 2095]: REMOTE max page width 1728 pixels in 215 mm
Feb 27 19:05:17.24: [ 2095]: REMOTE max unlimited page length
Feb 27 19:05:17.24: [ 2095]: REMOTE best vres 7.7 line/mm
Feb 27 19:05:17.24: [ 2095]: REMOTE best format 2-D MMR
Feb 27 19:05:17.24: [ 2095]: REMOTE supports T.30 Annex A, ECM
Feb 27 19:05:17.24: [ 2095]: REMOTE best 0 ms/scanline
Feb 27 19:05:17.24: [ 2095]: USE 14400 bit/s
Feb 27 19:05:17.24: [ 2095]: USE 0 ms/scanline
Feb 27 19:05:17.24: [ 2095]: SEND file "docq/doc176.cover;71"
Feb 27 19:05:17.24: [ 2095]: USE page width 1728 pixels in 215 mm
Feb 27 19:05:17.24: [ 2095]: USE unlimited page length
Feb 27 19:05:17.24: [ 2095]: USE 7.7 line/mm
Feb 27 19:05:17.24: [ 2095]: USE 2-D MR
Feb 27 19:05:17.24: [ 2095]: <-- [24:AT+FDIS=1,5,0,2,1,0,0,0\r]
Feb 27 19:05:17.40: [ 2095]: --> [2:OK]
Feb 27 19:05:17.40: [ 2095]: <-- [7:AT+FDT\r]
Feb 27 19:05:24.33: [ 2095]: --> [21:+FDCS:1,5,0,2,1,0,0,0]
Feb 27 19:05:24.68: [ 2095]: --> [7:CONNECT]
Feb 27 19:05:24.68: [ 2095]: SEND wait for XON
Feb 27 19:05:24.68: [ 2095]: --> [1:]
Feb 27 19:05:24.69: [ 2095]: SEND begin page
Feb 27 19:05:34.29: [ 2095]: SENT 14466 bytes of data
Feb 27 19:05:34.36: [ 2095]: SEND end page
Feb 27 19:05:41.93: [ 2095]: --> [2:OK]
Feb 27 19:05:41.93: [ 2095]: SEND send MPS (more pages, same document)
Feb 27 19:05:41.93: [ 2095]: <-- [9:AT+FET=0\r]
Feb 27 19:05:57.24: [ 2095]: --> [8:+FHNG:52]
Feb 27 19:05:57.24: [ 2095]: REMOTE HANGUP: No response to MPS repeated 3
times (code 52)
Feb 27 19:05:57.25: [ 2095]: SEND: No response to MPS repeated 3 times;
Giving up after 3 attempts to send same page "docq/doc176.cover;71", dirnum
0
Feb 27 19:05:57.25: [ 2095]: <-- [5:ATH0\r]
Feb 27 19:05:57.60: [ 2095]: --> [2:OK]
Feb 27 19:05:57.61: [ 2095]: SESSION END



# $Id: class2,v 1.2 1999/01/10 09:09:37 robert Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names
of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# Generic Class 2 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		1
AreaCode:		604
FAXNumber:		604.681.2025
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0644
LogFileMode:		0644
DeviceMode:		0666







RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"Strategic Communications"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use this to supply a hint
#ModemRate:		19200		# max rate for DCE-DTE communication
ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed
#ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
#ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:		""		# stuff to do when modem is reset
#ModemAnswerCmd:		ATA		# use this to answer phone
#ModemNoFlowCmd:		AT&K		# disable flow control cmd
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
#ModemSoftFlowCmd:	AT&K4		# software flow control cmd
#ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:	ATE0		# disable command echo
#ModemVerboseResultsCmd:	ATV1		# enable verbose command results
#ModemResultCodesCmd:	ATQ0		# enable result codes
#ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
#ModemSoftResetCmd:	ATZ		# do soft reset of modem
#ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds
ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
#ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
# Configuration parameters for Class 2 modems.
#
Class2Cmd:		AT+FCLASS=2	# command to enter class 2
Class2BORCmd:		AT+FBOR=0	# bit order for phase B/C/D (direct)
Class2RELCmd:		AT+FREL=0	# byte-align EOL codes on recv
Class2CQCmd:		""		# commands to enable copy quality proc.
Class2AbortCmd:		AT+FK		# abort session command
Class2CQQueryCmd:	AT+FCQ=?	# query for copy quality capabilities
Class2DCCQueryCmd:	AT+FDCC=?	# query for modem capabilities
Class2TBCCmd:		AT+FTBC=0	# setup stream mode
Class2CRCmd:		AT+FCR=1	# enable capability to receive
Class2PHCTOCmd:		AT+FPHCTO=30	# set phase C timeout parameter
Class2BUGCmd:		AT+FBUG=1	# enable HDLC frame tracing
Class2LIDCmd:		AT+FLID		# set local identifier command
Class2DCCCmd:		AT+FDCC		# set modem capabilities command
Class2DISCmd:		AT+FDIS		# set session parameters command
Class2DDISCmd:		""		# disable pre-dial DIS command hack
Class2CIGCmd:		AT+FCIG		# set polling identifier command
Class2PTSCmd:		AT+FPTS		# set post-page status command
Class2SPLCmd:		AT+FSPL		# set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger:	"\022"		# character sent to modem to start recv
Class2XmitWaitForXON:	yes		# if true, wait for XON before send



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null