[hylafax-users] ISIHP 4S modem config

[Axel Christiansen <a.christiansen@webseek.de>]

Hello,

im am locking for a modem-config
file for the MultiTech ISIHP 4S. can
someone tell what kind of modems they use
on such cards? a european config file
would just be fine. i used the faxaddmodem
script but it does not work in all cases.


thanks a lot

Axel

 CountryCode:            49
AreaCode:               40
FAXNumber:              +xxxxxxxxxxxxxx
LongDistancePrefix:     00
InternationalPrefix:    000
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "XXXXXXXXXXXXXXXX"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2          # use this to supply a hint
ModemRate:              19200           # max rate for DCE-DTE
communication
#ModemFlowControl:      xonxoff         # XON/XOFF flow control assumed
#ModemSetupDTRCmd:      AT&D2           # setup so DTR drop resets modem
#ModemSetupDCDCmd:      AT&C1           # setup so DCD reflects carrier
(or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:          ATDT%s@         # T for tone dialing, @ for
silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:                ""              # stuff to do when modem
is reset
#ModemAnswerCmd:                ATA             # use this to answer
phone
#ModemNoFlowCmd:                AT&K            # disable flow control
cmd
#ModemHardFlowCmd:      AT&K3           # hardware flow control cmd
#ModemSoftFlowCmd:      AT&K4           # software flow control cmd
#ModemNoAutoAnswerCmd:  ATS0=0          # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:     "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:       ATE0            # disable command echo
#ModemVerboseResultsCmd:        ATV1            # enable verbose command
results
#ModemResultCodesCmd:   ATQ0            # enable result codes
#ModemOnHookCmd:                ATH0            # place phone on hook
(hangup)
#ModemSoftResetCmd:     ATZ             # do soft reset of modem
#ModemWaitTimeCmd:      ATS7=60         # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:        ATS8=2          # comma pause time is 2
seconds
#ModemRecvFillOrder:    LSB2MSB         # bit order of received
facsimile
#ModemSendFillOrder:    LSB2MSB         # bit order modem expects for
transmit
ModemSendFillOrder:     LSB2MSB                 # as expected
ModemRecvFillOrder:     MSB2LSB                 # opposite of what makes
sense
# Configuration parameters for Class 2
modems.                                               
#
Class2Cmd:              AT+FCLASS=2     # command to enter class 2
Class2BORCmd:           AT+FBOR=0       # bit order for phase B/C/D
(direct)
Class2RELCmd:           AT+FREL=1       # byte-align EOL codes on recv
Class2CQCmd:            ""              # commands to enable copy
quality proc.
Class2AbortCmd:         AT+FK           # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality
capabilities
Class2DCCQueryCmd:      AT+FDCC=?       # query for modem capabilities
Class2TBCCmd:           AT+FTBC=0       # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FPHCTO=30    # set phase C timeout parameter
Class2BUGCmd:           AT+FBUG=1       # enable HDLC frame tracing
Class2LIDCmd:           AT+FLID         # set local identifier command
Class2DCCCmd:           AT+FDCC         # set modem capabilities command
Class2DISCmd:           AT+FDIS         # set session parameters command
Class2DDISCmd:          ""              # disable pre-dial DIS command
hack
Class2CIGCmd:           AT+FCIG         # set polling identifier command
Class2PTSCmd:           AT+FPTS         # set post-page status command
Class2SPLCmd:           AT+FSPL         # set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger:  ""              # character sent to modem to
start recv
Class2XmitWaitForXON:   yes             # if true, wait for XON before
send


**********************************************************************



Nov 03 15:49:14.60: [  593]: SESSION BEGIN 00000044 494030069391
Nov 03 15:49:14.60: [  593]: <-- [4:ATA\r]
Nov 03 15:49:28.39: [  593]: --> [5:+FCON]
Nov 03 15:49:28.39: [  593]: ANSWER: FAX CONNECTION
Nov 03 15:49:28.39: [  593]: RECV FAX: begin
Nov 03 15:49:28.39: [  593]: --> [28:+FTSI:"    +xxx"]
Nov 03 15:49:28.39: [  593]: REMOTE TSI "+xxx"
Nov 03 15:49:28.39: [  593]: --> [21:+FDCS:0,5,0,2,0,0,0,1]
Nov 03 15:49:28.39: [  593]: REMOTE wants 14400 bit/s
Nov 03 15:49:28.39: [  593]: REMOTE wants page width 1728 pixels in 215
mm
Nov 03 15:49:28.39: [  593]: REMOTE wants unlimited page length 
Nov 03 15:49:28.39: [  593]: REMOTE wants 3.85 line/mm
Nov 03 15:49:28.39: [  593]: REMOTE wants 1-D MR
Nov 03 15:49:28.39: [  593]: --> [2:OK]
Nov 03 15:49:28.39: [  593]: <-- [7:AT+FDR\r]
Nov 03 15:49:28.39: [  593]: --> [8:+FHNG:72]
Nov 03 15:49:28.39: [  593]: REMOTE HANGUP: COMREC error (code 72)
Nov 03 15:49:28.39: [  593]: RECV FAX (00000044): recvq/fax00036.tif
from +49 40 30069 199, route to <unspecified>, 0 pages in 0:00
Nov 03 15:49:28.39: [  593]: RECV FAX: COMREC error
Nov 03 15:49:28.39: [  593]: RECV FAX (00000044): session with +49 40
30069 199 terminated abnormally: COMREC error
Nov 03 15:49:28.39: [  593]: RECV FAX: bin/faxrcvd "recvq/fax00036.tif"
"ttyM1i" "00000044" "COMREC error"

                                                                                    
-- 
http://www.infoseek.de
Axel Christiansen - Technik/Tech Department - Netzwerk Administration
e-Mail: a.christiansen@webseek.de
WSI Webseek Infoservice GmbH & Co. KG
Tel./Phone +49-40-300 69 321 Fax +49-40-300 69 199
Buero/Office: Herrengraben 3, D- 20459 Hamburg
Post/mail: Brieffach 8250, D- 20350 Hamburg


____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null