Re: [hylafax-users] Courier I-Modem ISDN/V.34 Problem

[Christoph Scheeder <christoph.scheeder@scheeder.de>]

Hm,
slowly i' getting out of ideas....
but another try:
when you type the commands in minicom, how long does your modem to 
respond with OK ? is it fast or does it take some seconds?
perhaps you have to store some of the settings in nvram to get
the modem respond fast enough on initialisation for hylafax.
Christoph

C�dric Bole-Richard schrieb:
> 
> My version of HylaFAX is 4.1beta2.
> My modem is new, i have received it wednesday.
> I have tested :
> ModemResetCmds: ATZ\nAT
> ModemResetCmds: ATZ
> ModemResetCmds: AT&F1
> ModemResetCmds: ""
> 
> In minicom, all command are OK. If i type the same sequence that faxgetty in
> minicom, it's OK !
> 
> Always the same problem ...
> I'm desperate :-(
> 
> My modem :
>     USRobotics Courier I-Modem with ISDN/V.34
>         Product type : France External
>         Options : HST,V32bis,Terbo,V.FC,V34+,x2
>         Fax Options : Class 1/Class 2.0
>         Clock Freq : 20.16Mhz
>         Eprom : 768k
>         Ram : 256k
>         Supervisor date : 10/10/97
>         DSP date : 09/29/97
>         Supervisor rev : 2.2.2
>         DSP rev : 2.2.2
> 
> My config:
> CountryCode:  33
> AreaCode:  04
> FAXNumber:  0381000000
> LongDistancePrefix: 0
> InternationalPrefix: 00
> DialStringRules: etc/dialrules
> ServerTracing:  0x0f
> SessionTracing:  11
> RecvFileMode:  0600
> LogFileMode:  0600
> DeviceMode:  0600
> RingsBeforeAnswer: 0
> SpeakerVolume:  off
> GettyArgs:  "-h %l dx_%s"
> LocalIdentifier: "XXX"
> TagLineFont:  etc/lutRS18.pcf
> TagLineFormat:  "From %%l|%c|Page %%p of %%t"
> PercentGoodLines: 85
> MaxRecvPages:  25
> #
> ModemType:  Class2.0
> ModemRate:  38400
> ModemFlowControl: rtscts
> ModemNoFlowCmd:  AT&H0&I0&R1
> ModemHardFlowCmd: AT&H1&I0&R2
> ModemSoftFlowCmd: AT&H2&I2&R1
> ModemSetupDTRCmd: ATS13=1&D2
> ModemSetupDCDCmd: AT&C1
> ModemSetupAACmd: AT+FAA=1
> ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
> Class2BUGCmd:  AT+FBU=0
> Class2CQQueryCmd: !(0),(0)
> Class2NRCmd:  AT+FNR=1,1,1,0
> 
> # Ajoute par CBR
> 
> #JobReqBusy:  180
> #JobNoanswer:  180
> #JobNoCarrier:  180
> #JobReqOther:  180
> #NoCarrierRetrys: 1
> #Use2D:   yes
> 
> ModemDialCmd:  ATDT%s
> ModemResetCmds:  ""
> ModemAnswerCmd:  ATA
> ModemNoAutoAnswerCmd: ATS0=0
> ModemEchoOffCmd: ATE0
> ModemVerboseResultsCmd: ATV1
> ModemResultCodesCmd: ATQ0X4
> ModemOnHookCmd:  ATH0
> ModemSoftResetCmd: ATZ
> ModemWaitTimeCmd: ATS7=60
> ModemCommaPauseTimeCmd: ATS8=2
> ModemRecvFillOrder: LSB2MSB
> ModemSendFillOrder: LSB2MSB
> 
> Class2Cmd:  AT+FCLASS=2.0
> Class2APQueryCmd: ""
> Class2BORCmd:  AT+FB0=0
> Class2CQCmd:  ""
> #Class2CQCmd:  AT+FCQ=0,0
> Class2AbortCmd:  AT+FKS
> Class2DCCQueryCmd: AT+FCC=?
> Class2TBCCmd:  AT+FPP=0
> Class2CRCmd:  AT+FCR=1
> Class2PHCTOCmd:  AT+FCT=60
> Class2LIDCmd:  AT+FLI
> Class2DCCCmd:  AT+FCC
> Class2DISCmd:  AT+FIS
> Class2DDISCmd:  ""
> Class2CIGCmd:  AT+FPI
> Class2PIECmd:  AT+FIE=0
> Class2PTSCmd:  AT+FPS
> Class2SPLCmd:  AT+FSP
> Class2NFLOCmd:  AT+FLO=0
> Class2SFLOCmd:  AT+FLO=1
> Class2HFLOCmd:  AT+FLO=2
> 
> My log :
> Oct 24 17:54:22 Srv_Fabi02 FaxGetty[13358]: OPEN /dev/ttyS0
> Oct 24 17:54:22 Srv_Fabi02 FaxGetty[13358]: MODEM set DTR OFF
> Oct 24 17:54:22 Srv_Fabi02 FaxGetty[13358]: DELAY 2600 ms
> Oct 24 17:54:25 Srv_Fabi02 FaxGetty[13358]: MODEM set DTR ON
> Oct 24 17:54:25 Srv_Fabi02 FaxGetty[13358]: MODEM set baud rate: 19200 baud,
> input flow RTS/CTS, output flow RTS/CTS
> Oct 24 17:54:25 Srv_Fabi02 FaxGetty[13358]: MODEM flush i/o
> Oct 24 17:54:25 Srv_Fabi02 FaxGetty[13358]: <-- [17:ATE0V1Q0X4S0=0H0\r]
> Oct 24 17:54:30 Srv_Fabi02 FaxGetty[13358]: MODEM TIMEOUT: reading line from
> modem
> Oct 24 17:54:30 Srv_Fabi02 FaxGetty[13358]: MODEM <Timeout>
> Oct 24 17:54:30 Srv_Fabi02 FaxGetty[13358]: MODEM set DTR OFF
> Oct 24 17:54:30 Srv_Fabi02 FaxGetty[13358]: DELAY 2600 ms
> Oct 24 17:54:32 Srv_Fabi02 FaxGetty[13358]: MODEM set DTR ON
> Oct 24 17:54:32 Srv_Fabi02 FaxGetty[13358]: MODEM set baud rate: 19200 baud,
> input flow RTS/CTS, output flow RTS/CTS
> Oct 24 17:54:32 Srv_Fabi02 FaxGetty[13358]: MODEM flush i/o
> Oct 24 17:54:32 Srv_Fabi02 FaxGetty[13358]: <-- [17:ATE0V1Q0X4S0=0H0\r]
> Oct 24 17:54:37 Srv_Fabi02 FaxGetty[13358]: MODEM TIMEOUT: reading line from
> modem
> Oct 24 17:54:37 Srv_Fabi02 FaxGetty[13358]: MODEM <Timeout>
> Oct 24 17:54:37 Srv_Fabi02 FaxGetty[13358]: MODEM set DTR OFF
> Oct 24 17:54:37 Srv_Fabi02 FaxGetty[13358]: /dev/ttyS0: Can not initialize
> modem.
> 
> My syslog:
> Oct 24 17:54:37 Srv_Fabi02 FaxGetty[13358]: MODEM /dev/ttyS0 appears to be
> wedged
> 
> ----- Original Message -----
> From: Dmitry Bely <dbely@mail.ru>
> To: <hylafax-users@hylafax.org>
> Sent: Tuesday, Oct 24, 2000 10:27 PM
> Subject: Re: [hylafax-users] Courier I-Modem ISDN/V.34 Problem
> 
> > Christoph Scheeder <christoph.scheeder@scheeder.de> writes:
> >
> > > Hi again,
> > > in this situation i would try two things in this order:
> > > 1.) look if i can find a firmware-update for the modem, often
> > > modems with old firmware get delivered.
> > > If this does not fix the problem I would guess it is damaged.
> > > 2.) go to your dealer and let him replace the modem.
> > > Either by transport or it is one of those devices dieing after
> > > a very short period of time due to bad components.
> > > This happens more often than many people imagine.
> >
> > No. The real pronlem is that older Hylafax version just do not propely
> > reset the modem :-)
> >
> > To C�dric:
> >
> > try to add the following to your config.modem:
> >
> > ModemResetCmds: "ATZ\nAT"
> >
> > That is not needed for newer Hylafax versions, because they issue ATZ
> > themselves (ModemSoftResetCmd).
> >
> > Hope to hear from you soon,
> > Dmitry
> >


____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null