[hylafax-users] The first page is missing

[Hakan Koc <hkoc@tng.de>]

Hi,

I've installed Hylafax 4.1b2(patched) on a Suse 6.4 and libtiff 3.5.4,
tiff 3.5.4 with 2 modems (Elsa 28.8 and TKR 33.6). I took the original
Elsa-config (elsa.de).
Also, my tiff2ps doesn't work fine (bottom) orientated, the patch and
new compiling didn't do any change

and sometimes, a page is missing

/var/log/messages:
#these were 3 pages, the first is missing
Aug 17 14:02:52 alluminas FaxGetty[4851]: ANSWER: FAX CONNECTION
Aug 17 14:04:41 alluminas FaxGetty[4851]: RECV FAX (00000294): from
091114195782, page 1 in 1:44, INF, 7.7 line/mm, 1-D MR
Aug 17 14:05:21 alluminas FaxGetty[4851]: RECV FAX (00000294): from
091114195782, page 2 in 0:40, INF, 7.7 line/mm, 1-D MR
Aug 17 14:05:21 alluminas FaxGetty[4851]: RECV FAX (00000294):
recvq/fax00120.tif from 091114195782, route to <unspecified>, 2 
Aug 17 14:05:24 alluminas FaxGetty[4851]: RECV FAX: bin/faxrcvd
"recvq/fax00120.tif" "ttyS1" "00000294" ""
Aug 17 14:05:30 alluminas FaxGetty[4851]: MODEM "" "TKR TriStar"/"Ver.
1.09 vom 30.06.95"

var/spool/fax/log:

Aug 17 14:02:43.04: [ 4851]: SESSION BEGIN 00000294 494317097555
Aug 17 14:02:43.04: [ 4851]: <-- [4:ATA\r]
Aug 17 14:02:52.45: [ 4851]: --> [4:+FCO]
Aug 17 14:02:52.45: [ 4851]: ANSWER: FAX CONNECTION
Aug 17 14:02:52.45: [ 4851]: RECV FAX: begin
Aug 17 14:02:57.51: [ 4851]: --> [27:+FTI:"        091114195782"]
Aug 17 14:02:57.51: [ 4851]: REMOTE TSI "091114195782"
Aug 17 14:02:57.51: [ 4851]: --> [20:+FCS:1,5,0,2,0,0,0,1]
Aug 17 14:02:57.51: [ 4851]: REMOTE wants 14400 bit/s
Aug 17 14:02:57.51: [ 4851]: REMOTE wants page width 1728 pixels in 215
mm
Aug 17 14:02:57.51: [ 4851]: REMOTE wants unlimited page length 
Aug 17 14:02:57.51: [ 4851]: REMOTE wants 7.7 line/mm
Aug 17 14:02:57.51: [ 4851]: REMOTE wants 1-D MR
Aug 17 14:02:57.51: [ 4851]: --> [2:OK]
Aug 17 14:02:57.51: [ 4851]: <-- [7:AT+FDR\r]
Aug 17 14:03:00.20: [ 4851]: --> [7:CONNECT]
Aug 17 14:03:00.20: [ 4851]: RECV: begin page
Aug 17 14:03:00.20: [ 4851]: RECV: send trigger 022
Aug 17 14:03:00.20: [ 4851]: <-- data [1]
Aug 17 14:03:45.43: [ 4851]: RECV: 6745 bytes of data, 269 total lines
Aug 17 14:03:45.43: [ 4851]: --> [17:+FPS:2,209,F9,0,0]
Aug 17 14:03:46.69: [ 4851]: --> [6:+FET:0]
Aug 17 14:03:46.69: [ 4851]: RECV recv MPS (more pages, same document)
Aug 17 14:03:46.69: [ 4851]: --> [5:ERROR]
Aug 17 14:03:46.69: [ 4851]: MODEM Command error
Aug 17 14:03:46.69: [ 4851]: RECV send RTN (retrain negative)
Aug 17 14:03:46.69: [ 4851]: <-- [7:AT+FDR\r]
Aug 17 14:03:53.98: [ 4851]: --> [27:+FTI:"        091114195782"]
Aug 17 14:03:53.98: [ 4851]: REMOTE TSI "091114195782"
Aug 17 14:03:53.98: [ 4851]: --> [20:+FCS:1,4,0,2,0,0,0,1]
Aug 17 14:03:53.98: [ 4851]: REMOTE wants 12000 bit/s
Aug 17 14:03:53.98: [ 4851]: REMOTE wants page width 1728 pixels in 215
mm
Aug 17 14:03:53.98: [ 4851]: REMOTE wants unlimited page length 
Aug 17 14:03:53.98: [ 4851]: REMOTE wants 7.7 line/mm
Aug 17 14:03:53.98: [ 4851]: REMOTE wants 1-D MR
Aug 17 14:03:56.53: [ 4851]: --> [7:CONNECT]
Aug 17 14:03:56.53: [ 4851]: RECV: begin page
Aug 17 14:03:56.53: [ 4851]: RECV: send trigger 022
Aug 17 14:03:56.53: [ 4851]: <-- data [1]
Aug 17 14:04:21.91: [ 4851]: RECV: 32723 bytes of data, 1349 total lines
Aug 17 14:04:40.62: [ 4851]: RECV: 25403 bytes of data, 2264 total lines
Aug 17 14:04:40.70: [ 4851]: --> [16:+FPS:1,8D9,0,0,0]
Aug 17 14:04:41.87: [ 4851]: --> [6:+FET:0]
Aug 17 14:04:41.87: [ 4851]: RECV recv MPS (more pages, same document)
Aug 17 14:04:41.87: [ 4851]: --> [2:OK]
Aug 17 14:04:41.87: [ 4851]: RECV send MCF (message confirmation)
Aug 17 14:04:41.87: [ 4851]: RECV FAX (00000294): from 091114195782,
page 1 in 1:44, INF, 7.7 line/mm, 1-D MR
Aug 17 14:04:41.87: [ 4851]: <-- [7:AT+FDR\r]
Aug 17 14:04:44.75: [ 4851]: --> [7:CONNECT]
Aug 17 14:04:44.75: [ 4851]: RECV: begin page
Aug 17 14:04:44.75: [ 4851]: RECV: send trigger 022
Aug 17 14:04:44.75: [ 4851]: <-- data [1]
Aug 17 14:05:11.35: [ 4851]: RECV: 32740 bytes of data, 1794 total lines
Aug 17 14:05:20.29: [ 4851]: RECV: 11937 bytes of data, 2270 total lines
Aug 17 14:05:20.29: [ 4851]: --> [16:+FPS:1,8DF,0,0,0]
Aug 17 14:05:21.53: [ 4851]: --> [6:+FET:2]
Aug 17 14:05:21.53: [ 4851]: RECV recv EOP (no more pages or documents)
Aug 17 14:05:21.53: [ 4851]: --> [2:OK]
Aug 17 14:05:21.53: [ 4851]: RECV send MCF (message confirmation)
Aug 17 14:05:21.53: [ 4851]: RECV FAX (00000294): from 091114195782,
page 2 in 0:40, INF, 7.7 line/mm, 1-D MR
Aug 17 14:05:21.53: [ 4851]: RECV FAX (00000294): recvq/fax00120.tif
from 091114195782, route to <unspecified>, 2 pages in 2:29
Aug 17 14:05:21.53: [ 4851]: <-- [7:AT+FDR\r]
Aug 17 14:05:24.67: [ 4851]: --> [7:+FHS:00]
Aug 17 14:05:24.67: [ 4851]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Aug 17 14:05:24.67: [ 4851]: RECV FAX: bin/faxrcvd "recvq/fax00120.tif"
"ttyS1" "00000294" ""
Aug 17 14:05:25.37: [ 4851]: RECV FAX: end
Aug 17 14:05:25.37: [ 4851]: SESSION END

config:

ModemType:              Class2.0        # use this to supply a hint
ModemRate:              115200          # max rate for DCE-DTE
communication
ModemFlowControl:       rtscts          # XON/XOFF flow control assumed
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
(or not)

ModemDialCmd:           ATDT%s

ModemResetCmds:         ATX3            # stuff to do when modem is
reset
ModemAnswerCmd:         ATA             # use this to answer phone
ModemNoFlowCmd:         AT\Q0
ModemHardFlowCmd:       AT\Q3
ModemSoftFlowCmd:       AT\Q1
ModemNoAutoAnswerCmd:   ATS0=0          # disable auto-answer

ModemSetVolumeCmd:      "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:        ATE0            # disable command echo
ModemVerboseResultsCmd: ATV1            # enable verbose command results
ModemResultCodesCmd:    ATQ0            # enable result codes
ModemOnHookCmd:         ATH             # place phone on hook (hangup)
ModemSoftResetCmd:      ATZ             # do soft reset of modem
ModemWaitTimeCmd:       ATS7=60         # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2          # comma pause time is 2 seconds
ModemRecvFillOrder:     LSB2MSB         #bit order of received facsimile
ModemSendFillOrder:     LSB2MSB         #bit order modem expects for
transmit

Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0
Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D
(direct)
Class2CQCmd:            ""              # commands to enable copy
quality proc.
Class2AbortCmd:         AT+FKS          # abort session command
Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality
capabilities
Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities
Class2TBCCmd:           AT+FPP=0        # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter
Class2BUGCmd:           AT+FBU=1        # enable HDLC frame tracing
Class2LIDCmd:           AT+FLI          # set local identifier command
Class2DCCCmd:           AT+FCC          # set modem capabilities command
Class2DISCmd:           AT+FIS          # set session parameters command
Class2DDISCmd:          ""              # disable pre-dial DIS command
hack
Class2CIGCmd:           AT+FPI          # set polling identifier command
Class2NRCmd:            AT+FNR=1,1,1,1  # setup status reporting command
Class2PIECmd:           AT+FIE=0        # disable interrupt-enable
command
Class2PTSCmd:           AT+FPS          # set post-page status command
Class2SPLCmd:           AT+FSP          # set polling indicator command
Class2NFLOCmd:          AT+FLO=0        # set no flow control command
Class2SFLOCmd:          AT+FLO=1        # set software flow control
command
Class2HFLOCmd:          AT+FLO=2        # set hardware flow control
command


Thank you for any help.

Hakan Koc
from Germany


____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null