HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] Re: Wanted ALL Config files for USR/3com 56K in Class 1,2,2.0



Brendin, there is no such thing as a USR/3Com Class 2.  They only use Class
1 & 2.0 that I know of.  Here's an untested Class 1 config file.

# Modem-related stuff: should reflect modem command interface
# and
hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		#
use this to supply a hint
ModemRate:		38400			# rate for DCE-DTE
communication
ModemFlowControl:	rtscts		# RTSCTS flow control assumed
#
ModemSetupDTRCmd:		ATS13=1&D2	# setup so DTR drop resets
modem
ModemSetupDCDCmd:		AT&C1		# setup so DCD follows carrier
#
# We
normally append the "@" symbol to the dial string so that
# the modem will
wait 5 seconds before attempting to connect
# and return result codes that
distinguish between no carrier
# and no answer.  This makes it possible to
avoid problems with
# repeatedly dialing a number that doesn't have a fax
machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to
prefix phone numbers to get through a PBX,
#     put it in the
ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:		ATDT%s@		# T for tone
dialing, @ for silence
#
# Other possible configuration stuff.  The default
strings are
# shown below.  Only those that are different from the
defaults
# need to be included in the configuration file.
#
ModemResetCmds:
	""		# stuff to do when modem is reset
ModemAnswerCmd:		ATA		# use this to
answer phone
ModemNoFlowCmd:		AT&H0&I0&R1		# disable flow control
cmd
ModemHardFlowCmd:		AT&H1&I0&R2		# hardware flow control
cmd
ModemSoftFlowCmd:		AT&H2&I2&R1		# software flow control
cmd
ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem
speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both
turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:	"ATM0 ATL0M1
ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:		ATE0		# disable command
echo
ModemVerboseResultsCmd:	ATV1		# enable verbose command
results
ModemResultCodesCmd:	ATQ0X4	# enable result codes
ModemOnHookCmd:
ATH0		# place phone on hook (hangup)
ModemSoftResetCmd:	ATZ		# do soft
reset of modem
ModemWaitTimeCmd:		ATS7=60	# wait 60 seconds for
carrier
ModemCommaPauseTimeCmd:	ATS8=2	# comma pause time is 2
seconds
ModemRecvFillOrder:	LSB2MSB	# bit order of received
facsimile
ModemSendFillOrder:	LSB2MSB	# bit order modem expects for
transmit
ModemSetupAACmd:		AT+FAA=1	# setup adaptive answer
#
Class1Cmd:			AT+FCLASS=1	# command to enter class
1
Class1TCFResponseDelay:	75		# 75ms delay between recv TCF &
response
Class1SendPPMDelay:	75		# 75ms delay before sending
PPM
Class1SendTCFDelay:	75		# 75ms delay between sending DCS &
TCF
Class1TrainingRecovery:	1500		# 1.5sec delay after training
failure
Class1RecvAbortOK:	200		# wait 200ms for abort
response
Class1FrameOverhead:	4		# 4 byte overhead in recvd HDLC
frames
Class1RecvIdentTimer:	40000		# 35+5secs waiting for ident
frames
Class1TCFMaxNonZero:	10		# max 10% of data may be
non-zero
Class1TCFMinRun:		1000		# min run is 2/3rds of TCF duration

At 07:04 PM 7/10/00 -0700, Brendin Emslie wrote:
>I am testing 3COM/USR modems, specifically external 56K faxmodem, and would
>like to try other config files.  I send out 1300+ faxes a day so I will be
>able to put them through their paces.
>
>I will try each config file for one days worth of faxes and I will post the
>results here.
>
>
>
>
>____________________ HylaFAX(tm) Users Mailing List _______________________
> To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
>



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null




Project hosted by iFAX Solutions