[hylafax-users] Re: Remote sends 2 pages I get only one

[Dmitry Bely <dbely@mail.ru>]

Alvaro Rosales <alvaro@procacao.wintersperu.com.pe> writes:

>  Hi fellows Im using Hylafax in a send and receive environment  it works
> ok , but when  someone sendme a fax  with two or more pages ,(the sender
> doesnt get any error) I only get the first page , this is the log , I
> hope you can help me

Help you to do what? Change the remote fax machine settings? Hylafax just
was asked to interrupt transmission for the operator intervention (PRI-EOP
meaning according to T.30) -- and followed this directive. BTW, you logs is
almost useless at this tracing level: it's absolutely unclear which HDLC
frames were sent/received. So use in future SessionTracing=0x7ff,
if you are going to ask a fax protocol-related question.

> Jun 06 14:41:14.89: [  656]: SESSION BEGIN 00000481 11260
> Jun 06 14:41:14.89: [  656]: <-- [4:ATA\r]
> Jun 06 14:41:20.41: [  656]: --> [7:CONNECT]
> Jun 06 14:41:20.41: [  656]: ANSWER: FAX CONNECTION
> Jun 06 14:41:20.41: [  656]: RECV FAX: begin
> Jun 06 14:41:20.41: [  656]: <-- data [23]
> Jun 06 14:41:20.42: [  656]: <-- data [2]
> Jun 06 14:41:22.10: [  656]: --> [7:CONNECT]
> Jun 06 14:41:22.10: [  656]: <-- data [10]
> Jun 06 14:41:22.10: [  656]: <-- data [2]
> Jun 06 14:41:22.64: [  656]: --> [2:OK]
> Jun 06 14:41:22.64: [  656]: <-- [9:AT+FRH=3\r]
> Jun 06 14:41:23.04: [  656]: --> [7:CONNECT]
> Jun 06 14:41:24.51: [  656]: --> [2:OK]
> Jun 06 14:41:24.51: [  656]: REMOTE TSI "5114700651"
> Jun 06 14:41:24.51: [  656]: <-- [9:AT+FRH=3\r]
> Jun 06 14:41:24.53: [  656]: --> [7:CONNECT]
> Jun 06 14:41:24.80: [  656]: --> [2:OK]
> Jun 06 14:41:24.80: [  656]: REMOTE wants 9600 bit/s
> Jun 06 14:41:24.80: [  656]: REMOTE wants page width 1728 pixels in 215
> mm
> Jun 06 14:41:24.80: [  656]: REMOTE wants unlimited page length
> Jun 06 14:41:24.80: [  656]: REMOTE wants 3.85 line/mm
> Jun 06 14:41:24.80: [  656]: REMOTE wants 1-D MR
> Jun 06 14:41:24.80: [  656]: RECV training at v.29 9600 bit/s
> Jun 06 14:41:24.80: [  656]: <-- [10:AT+FRM=96\r]
> Jun 06 14:41:25.16: [  656]: --> [7:CONNECT]
> Jun 06 14:41:26.69: [  656]: RECV: TCF 1820 bytes, 1% non-zero, 1781
> zero-run
> Jun 06 14:41:26.70: [  656]: --> [10:NO CARRIER]
> Jun 06 14:41:26.70: [  656]: DELAY 75 ms
> Jun 06 14:41:26.78: [  656]: <-- [9:AT+FTH=3\r]
> Jun 06 14:41:26.83: [  656]: --> [7:CONNECT]
> Jun 06 14:41:26.83: [  656]: <-- data [3]
> Jun 06 14:41:26.83: [  656]: <-- data [2]
> Jun 06 14:41:28.14: [  656]: --> [2:OK]
> Jun 06 14:41:28.14: [  656]: TRAINING succeeded
> Jun 06 14:41:28.14: [  656]: <-- [10:AT+FRM=96\r]
> Jun 06 14:41:29.46: [  656]: --> [7:CONNECT]
> Jun 06 14:41:29.46: [  656]: RECV: begin page
> Jun 06 14:42:04.48: [  656]: RECV: 1163 total lines, 0 bad lines, 0
> consecutive bad lines
> Jun 06 14:42:04.49: [  656]: RECV: end page
> Jun 06 14:42:04.49: [  656]: --> [10:NO CARRIER]
> Jun 06 14:42:04.49: [  656]: <-- [9:AT+FRH=3\r]
> Jun 06 14:42:07.89: [  656]: --> [7:CONNECT]
> Jun 06 14:42:08.85: [  656]: --> [2:OK]
> Jun 06 14:42:08.85: [  656]: RECV recv MPS (more pages, same document)
> Jun 06 14:42:08.85: [  656]: <-- [9:AT+FTH=3\r]
> Jun 06 14:42:08.90: [  656]: --> [7:CONNECT]
> Jun 06 14:42:08.90: [  656]: <-- data [3]
> Jun 06 14:42:08.90: [  656]: <-- data [2]
> Jun 06 14:42:10.22: [  656]: --> [2:OK]
> Jun 06 14:42:10.22: [  656]: RECV send MCF (message confirmation)
> Jun 06 14:42:10.22: [  656]: RECV FAX (00000481): from 5114700651, page
> 1 in 0:42, INF, 3.85 line/mm, 1-D M
> R
> Jun 06 14:42:10.22: [  656]: <-- [10:AT+FRM=96\r]
> Jun 06 14:42:11.54: [  656]: --> [7:CONNECT]
> Jun 06 14:42:11.54: [  656]: RECV: begin page
> Jun 06 14:42:44.36: [  656]: RECV: 1165 total lines, 0 bad lines, 0
> consecutive bad lines
> Jun 06 14:42:44.37: [  656]: RECV: end page
> Jun 06 14:42:44.37: [  656]: --> [10:NO CARRIER]
> Jun 06 14:42:44.37: [  656]: <-- [9:AT+FRH=3\r]
> Jun 06 14:42:44.76: [  656]: --> [7:CONNECT]
> Jun 06 14:42:45.57: [  656]: --> [2:OK]
> Jun 06 14:42:45.57: [  656]: RECV recv PRI-EOP (no more pages after
> interrupt)
> Jun 06 14:42:45.57: [  656]: <-- [9:AT+FTH=3\r]
> Jun 06 14:42:45.62: [  656]: --> [7:CONNECT]
> Jun 06 14:42:45.62: [  656]: <-- data [3]
> Jun 06 14:42:45.62: [  656]: <-- data [2]
> Jun 06 14:42:46.94: [  656]: --> [2:OK]
> Jun 06 14:42:46.94: [  656]: RECV send MCF (message confirmation)
> Jun 06 14:42:46.94: [  656]: RECV FAX (00000481): from 5114700651, page
> 2 in 0:36, INF, 3.85 line/mm, 1-D M
> R
> Jun 06 14:42:46.94: [  656]: RECV FAX (00000481): recvq/fax00167.tif
> from 5114700651, route to <unspecified
> >, 2 pages in 1:26
> Jun 06 14:42:46.94: [  656]: <-- [9:AT+FRH=3\r]
> Jun 06 14:42:47.34: [  656]: --> [7:CONNECT]
> Jun 06 14:42:48.26: [  656]: --> [2:OK]
> Jun 06 14:42:48.26: [  656]: RECV FAX: bin/faxrcvd "recvq/fax00167.tif"
> "ttyS3" "00000481" ""
> Jun 06 14:42:48.87: [  656]: RECV FAX: end
> Jun 06 14:42:48.87: [  656]: SESSION END

Hope to hear from you soon,
Dmitry




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null