HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: help!!



Dear expert:

I attach the config.ttyS0 and the log of one of the failed faxes.

PS: When I use " tail -f /var/log/messages "  to monitor the status, it says

    HylaFAX[582]: Filesystem has sysV-style file creation semantics
FaxQueuer[518]: SUBMIT JOB 5
    FaxGetty[560]: Answer : Can not lock modem device
    FaxSend[583]: MODEM ROCKWELL AC/K56/V2.200-V90_2M_DLS
    FaxSend[583]: SEND FAX : JOB 5 DEST 87654321 COMMID 00000007
FaxQueuer[518]:  Notify : bin/notify "doneq/q5" "done" "0:22"
FaxQueuer[518]:  Bad exit status 041400 for "bin/notify "doneq/q5" "done"
"0:22""
    FaxGetty[560]:  MODEM ROCKWELL AC/K56/V2.200-V90_2M_DLS


# $Id: rockwell,v 1.1.1.1 1998/10/12 20:47:48 root Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for a Rockwell-based modem not otherwise handled by
# another prototype configuration file.  This file assumes the modem
# is compatible with the Rc144AC, RC96AC or RC144DP.
#
# This configuration file sets up the modem to run at 38.4 with
# RTS/CTS flow control used by default.  XON/XOFF is automatically
# enabled for fax recv.  Beware of modems that also lock sending
# to 19.2; add ModemSendBeginCmd: "<19200>" if this is required.
# Also beware that the adaptive-answer facility, when supported,
# is often unreliable.
#
#
CountryCode:		86
AreaCode:		20
FAXNumber:		"+86 20 81234567"
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		high
GettyArgs:		"-h %l dx_%s"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		50
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use class 2 interface
ModemRate:		38400
ModemFlowControl:	rtscts		# default
#
#ModemResetCmds:	AT&F2		# what you want for a Supra
ModemNoFlowCmd:		AT&K		# disable flow control cmd
ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
ModemSoftFlowCmd:	AT&K4		# software flow control cmd
ModemSetupDTRCmd:	AT&D3		# DTR off causes modem to reset
#ModemSetupDTRCmd:	AT&D2S25=1S38=0	# Dynalink 1414VE needs this
ModemSetupDCDCmd:	AT&C1		# DCD follows carrier
ModemSetupAACmd:	AT+FAA=1+FCLASS=0 # enable in current class
#
ModemSendFillOrder:	LSB2MSB		# as expected
ModemRecvFillOrder:	MSB2LSB		# opposite of what makes sense
#
ModemAnswerFaxBeginCmd:	"<19200><xon>"	# modem switches on fax receive
#
# Caller ID configuration setup for Supra.
#
#QualifyCID:		etc/cid		# CID access control list file
#CIDNumber:		"NMBR = "	# pattern string for phone number info
#CIDName:		"NAME = "	# pattern string for identity info
Feb 24 09:26:31.06: [  583]: SESSION BEGIN 00000007 862081234567
Feb 24 09:26:31.06: [  583]: SEND FAX: JOB 5 DEST 87654321 COMMID 00000007
Feb 24 09:26:31.06: [  583]: DELAY 2600 ms
Feb 24 09:26:33.65: [  583]: <-- [15:ATE0V1Q0S0=0H0\r]
Feb 24 09:26:33.66: [  583]: --> [2:OK]
Feb 24 09:26:33.66: [  583]: <-- [21:ATS8=2S7=60&K3&D3&C1\r]
Feb 24 09:26:33.68: [  583]: --> [2:OK]
Feb 24 09:26:33.68: [  583]: <-- [12:AT+FCLASS=2\r]
Feb 24 09:26:33.69: [  583]: --> [2:OK]
Feb 24 09:26:33.69: [  583]: <-- [10:AT+FTBC=0\r]
Feb 24 09:26:33.70: [  583]: --> [2:OK]
Feb 24 09:26:33.70: [  583]: <-- [10:AT+FBOR=0\r]
Feb 24 09:26:33.71: [  583]: --> [2:OK]
Feb 24 09:26:33.71: [  583]: <-- [13:AT+FPHCTO=30\r]
Feb 24 09:26:33.72: [  583]: --> [2:OK]
Feb 24 09:26:33.72: [  583]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Feb 24 09:26:33.73: [  583]: --> [2:OK]
Feb 24 09:26:33.73: [  583]: <-- [7:ATL3M1\r]
Feb 24 09:26:33.74: [  583]: --> [2:OK]
Feb 24 09:26:33.74: [  583]: <-- [12:AT+FCLASS=2\r]
Feb 24 09:26:33.85: [  583]: --> [2:OK]
Feb 24 09:26:33.85: [  583]: <-- [10:AT+FTBC=0\r]
Feb 24 09:26:33.96: [  583]: --> [2:OK]
Feb 24 09:26:33.96: [  583]: <-- [10:AT+FBOR=0\r]
Feb 24 09:26:34.07: [  583]: --> [2:OK]
Feb 24 09:26:34.07: [  583]: <-- [13:AT+FPHCTO=30\r]
Feb 24 09:26:34.18: [  583]: --> [2:OK]
Feb 24 09:26:34.18: [  583]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Feb 24 09:26:34.29: [  583]: --> [2:OK]
Feb 24 09:26:34.29: [  583]: <-- [24:AT+FLID="+862081234567"\r]
Feb 24 09:26:34.40: [  583]: --> [2:OK]
Feb 24 09:26:34.42: [  583]: DIAL 87654321
Feb 24 09:26:34.42: [  583]: <-- [13:ATDT87654321\r]
Feb 24 09:26:45.09: [  583]: --> [5:+FCON]
Feb 24 09:26:46.76: [  583]: --> [22:+FDIS: 1,3,0,2,1,0,0,3]
Feb 24 09:26:46.87: [  583]: --> [2:OK]
Feb 24 09:26:46.87: [  583]: REMOTE best rate 9600 bit/s
Feb 24 09:26:46.87: [  583]: REMOTE max page width 1728 pixels in 215 mm
Feb 24 09:26:46.87: [  583]: REMOTE max unlimited page length 
Feb 24 09:26:46.87: [  583]: REMOTE best vres 7.7 line/mm
Feb 24 09:26:46.87: [  583]: REMOTE best format 2-D MR
Feb 24 09:26:46.87: [  583]: REMOTE best 10 ms/scanline
Feb 24 09:26:46.87: [  583]: USE 9600 bit/s
Feb 24 09:26:46.87: [  583]: USE 10 ms/scanline
Feb 24 09:26:46.87: [  583]: <-- [5:ATH0\r]
Feb 24 09:26:47.13: [  583]: --> [9:+FHNG: 20]
Feb 24 09:26:47.13: [  583]: REMOTE HANGUP: Unspecified Transmit Phase B error (code 20)
Feb 24 09:26:48.94: [  583]: --> [2:OK]
Feb 24 09:26:48.94: [  583]: SESSION END



Project hosted by iFAX Solutions