flexfax: Strange problem receiving fax in US-robotics

["Evandro Humberto Rodrigues" <evandro.dnapl@smar.com.br>]

Hi All,

 

    I'm using hylafax to receive and print faxes.

    Something strange is happening, when I send a fax to my computer with hylafax without use the handset of the fax machine to listen the inicial fax sound, the transmission is completly susseful.

    But when I get the handset of the fax machine and wait a fax sound (of hylafax station) before press the START key, the transmission doesn't occours.

    I will attach the config.ttyS1 and a log with the problem, if someone can help me I will be very greatful.

 

--------------------- Start of config.ttyS1 ----------------------------------

# $Id: usr-2.0,v 1.7 1996/06/24 02:58:42 sam Rel $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

 

#
# Configuration for using the Class 2.0 command interface
# with a USR v.34 Courier or Sporster modem.
#
# RTS/CTS flow control is used default.
#
#
CountryCode:  55
AreaCode:  2116
FAXNumber:  "16-645-3599 R.583"
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing:  1
SessionTracing:  4095
RecvFileMode:  0600
LogFileMode:  0600
DeviceMode:  0600
RingsBeforeAnswer: 1
SpeakerVolume:  off
GettyArgs:  "-r -b -s %s %l"
LocalIdentifier: "Smar - Administracao de Contratos"
TagLineFont:  etc/lutRS18.pcf
TagLineFormat:  "From %%l|%c|Page %%p of %%t"
MaxRecvPages:  150

#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:  Class2.0 # use class 2.0 interface
ModemRate:  38400  # DCE-DTE communication rate
ModemFlowControl: rtscts   # XON/XOFF flow control assumed
#ModemSetupDTRCmd: ATS13=1&D2
#ModemSetupDCDCmd: AT&C1

 

ModemAnswerFaxBeginCmd: "<19200><xon>"

 

#                       rtscts / xonxoff
#
ModemNoFlowCmd:  AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
ModemSetupDTRCmd: ATS13=0&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1  # setup so DCD reflects carrier
ModemResultCodesCmd: ATQ0X3
#
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#
ModemSetupAACmd: AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd:  AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
# response so that the server will do copy quality checking.
#
Class2CQQueryCmd: !(0),(0) # override modem response
-------------------------------- End of config.ttyS1 --------------------------

 

 

--------------------------------- Start of a log with the problem ---------------------

Dec 06 13:33:07.14: [ 1605]: SESSION BEGIN 00000132 5521161664535997583
Dec 06 13:33:07.14: [ 1605]: <-- [4:ATA\r]
Dec 06 13:33:22.57: [ 1605]: --> [4:+FDM]
Dec 06 13:33:22.57: [ 1605]: ANSWER: DATA CONNECTION
Dec 06 13:33:22.59: [ 1605]: GETTY: START "/sbin/getty -r -b -s 38400 ttyS1", pid 1631
Dec 06 13:33:22.59: [ 1605]: STATE CHANGE: ANSWERING -> GETTYWAIT
Dec 06 13:33:22.71: [ 1605]: GETTY: exit status 077400
Dec 06 13:33:22.72: [ 1605]: SESSION END
--------------------------------End of a log -------------------------------------

 

____________________________

Evandro Humberto Rodrigues

email: evandro.dnapl@smar.com.br