flexfax: MT3334ZDX Fax Sending Problems

[Ken McCord <ken@themccords.com>]

Having problems receiving faxes via a MultiTech MT3334ZDX.  Faxes being
sent are fine, as well as faxes being sent and received via a MT2334ZDX,
attached to the same fax server.   I've tried modifying the config file
as mentioned in the archives, but no go.  I've attached a copy of a
sample fax that was received, as well as the config.ttyXX file I'm
using.  Any help would be appreciated.

Thanks,

Ken McCord
MIS Manager
A.C. Coin and Slot

fax00035.tif

# $Id: mt-1432,v 1.23 1996/06/24 02:58:36 sam Rel $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for a Multi-Tech MT1432, MT224BA, and MT1932ZDX modems.
#
# MT1432	firmware rev 0307 I or newer
# MT132BG	rev 0109A
# MT1932ZDX	rev 0109H
#
# Note that MT1432 modems come in several varieties:
#
# MT1432BA	uses Rockwell data pump
# MT1432BA/A	uses AT&T data pump
# MT1432BG	MT1432BA tweaked for German FCC
# MT1432MK	(for UK?)
#
# The modem has been tried with both XON/XOFF and RTS/CTS flow
# control; this configuration is for hardware flow control.
#
#
CountryCode:		1
AreaCode:		609
FAXNumber:		+1.609.641.1316
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	"etc/dialrules"
ServerTracing:		0x08F2F
SessionTracing:		0x08F2F
RecvFileMode:		0640
LogFileMode:		0640
DeviceMode:		0660
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-r -b -s %s %l"
LocalIdentifier:	"A. C. Coin and Slot"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use class 2 interface
ModemRate:		38400		# lock rate for DCE-DTE communication
ModemFlowControl:	rtscts		# default
#
#ModemHardFlowCmd:	AT&E4		# hardware flow control
#ModemSoftFlowCmd:	AT&E5		# software flow control
ModemHardFlowCmd:	AT&K3		# hardware flow control
ModemSoftFlowCmd:	AT&K4		# software flow control
ModemSetupDTRCmd:	AT&D3		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
ModemSetupAACmd:	AT+FAA=1	# enable adaptive-answer in class 2
#
# NB: some models get confused by the @
#
#ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
ModemDialCmd:		ATDT%s		# T for tone dialing, @ for silence
#
Class2RecvDataTrigger:	"\022"		# character sent to modem to start recv