flexfax: Modem fax�es thin strokes frequently

[Ekkard Gerlach <SPS_Gerlach@online.de>]

platform Linux (Suse 6.1), hylafax, faxgetty
============================================



Hello,

my external modem ("Arowana", 57,6 , 1/2 year old, 
Texas Instruments-chipset) faxes 
frequently thin strokes in confused order 
in then second part of some of my fax�es
thant I send.

Who can help?

Thanks in advance, Ekkard



Further data :

1. using Linux, Hylafax, faxgetty

2. The thin strokes that appear on serveral 
receiving stations. The fault is with the 
sending station (my modem).  The fault happens
with 9600 baud or with 14400 baud (tested with 
an old 9600baud-receiving station and with an 
newer one with 14400)

3. The thin strokes are dependant of the format of 
the fax. The errors I have detected so far always
occured with letters with standard letter format:
sender, receiver, place & Date on the top. 
When I delete the sender and receiver on my letter
the fax was sended without error (=fine strokes) !!!!

4. I can send the fax for serveral times. The error
occurs each time. The error is 100% reproduceable.

5. faxgetty doesn�t detect any fault. In 
/var/log/messages   there appears "... done ..."
as if all would be all right. 

6. My config.ttyS1  (same as config.modem)
produced by faxaddmodem :
#
# Generic Class 2.0 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:  49
AreaCode:  721
FAXNumber:  +49.721.88888888           (manipulated, Ekkard)
LongDistancePrefix: 0
InternationalPrefix: 0049
DialStringRules: etc/dialrules
ServerTracing:  527
SessionTracing:  527
RecvFileMode:  0644
LogFileMode:  0600
DeviceMode:  0666
RingsBeforeAnswer: 5
SpeakerVolume:  high
GettyArgs:  "-r -b -s %s %l"
LocalIdentifier: "Ekkard Gerlach"
TagLineFont:  etc/lutRS18.pcf
TagLineFormat:  "From %%l|%c|Page %%p of %%t"
MaxRecvPages:  25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:  Class2.0 # use this to supply a hint
#ModemRate:  19200  # max rate for DCE-DTE communication
#ModemFlowControl: xonxoff  # XON/XOFF flow control assumed
#ModemSetupDTRCmd: AT&D2  # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1  # setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:  ATDT%s@  # T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:  ""  # stuff to do when modem is reset
#ModemAnswerCmd:  ATA  # use this to answer phone
#ModemNoFlowCmd:  AT&K  # disable flow control cmd
#ModemHardFlowCmd: AT&K3  # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4  # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0  # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
# ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"

# speaker always "on" (ekkard):
ModemSetVolumeCmd: ATM2L3

#ModemEchoOffCmd: ATE0  # disable command echo
#ModemVerboseResultsCmd: ATV1  # enable verbose command results
#ModemResultCodesCmd: ATQ0  # enable result codes
#ModemOnHookCmd:  ATH0  # place phone on hook (hangup)
#ModemSoftResetCmd: ATZ  # do soft reset of modem
ModemWaitTimeCmd: ATS7=150    # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2  # comma pause time is 2 seconds
#ModemRecvFillOrder: LSB2MSB  # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB  # bit order modem expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:  AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd:  AT+FBO=0 # bit order for phase B/C/D (direct)
Class2CQCmd:  ""  # commands to enable copy quality proc.
Class2AbortCmd:  AT+FKS  # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd:  AT+FPP=0 # setup stream mode
Class2CRCmd:  AT+FCR=1 # enable capability to receive
Class2PHCTOCmd:  AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd:  AT+FBU=1 # enable HDLC frame tracing
Class2LIDCmd:  AT+FLI  # set local identifier command
Class2DCCCmd:  AT+FCC  # set modem capabilities command
Class2DISCmd:  AT+FIS  # set session parameters command
Class2DDISCmd:  ""  # disable pre-dial DIS command hack
Class2CIGCmd:  AT+FPI  # set polling identifier command
Class2NRCmd:  AT+FNR=1,1,1,1 # setup status reporting command
Class2PIECmd:  AT+FIE=0 # disable interrupt-enable command
Class2PTSCmd:  AT+FPS  # set post-page status command
Class2SPLCmd:  AT+FSP  # set polling indicator command
Class2NFLOCmd:  AT+FLO=0 # set no flow control command
Class2SFLOCmd:  AT+FLO=1 # set software flow control command
Class2HFLOCmd:  AT+FLO=2 # set hardware flow control command


has somebody an idea ? thank you
Ekkard