HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

ACPD SA2 to 4805546454 requeued (fwd)



I have a 3COM USR 56k Faxmodem, model 5687-02. I keep getting the error
below when I try to send a fax using hylax fax ver 4.0pl2.

Thanks.

Your facsimile job to 4805546454 was not sent because:
    Unspecified Transmit Phase D error, including +FPHCTO timeout between
data and +FET command  

_______________________________________
Michael Alexander Green
http://www.reesie.digitalf.com/~magreen

---------- Forwarded message ----------
Date: Sun, 7 Nov 1999 14:12:55 -0700
From: Facsimile Agent <fax@reesie.digitalf.com>
To: magreen@reesie.digitalf.com
Subject: ACPD SA2 to 4805546454 requeued

Your facsimile job to 4805546454 was not sent because:
    Unspecified Transmit Phase D error, including +FPHCTO timeout between data and +FET command

The job will be retried at 14:17.

    ---- Transcript of session follows ----

Nov 07 14:08:44.20: [ 1460]: SESSION BEGIN 00000005 14804805546454
Nov 07 14:08:44.20: [ 1460]: SEND FAX: JOB 6 DEST 4805546454 COMMID 00000005
Nov 07 14:08:44.20: [ 1460]: DELAY 2600 ms
Nov 07 14:08:46.80: [ 1460]: <-- [15:ATE0V1Q0S0=0H0\r]
Nov 07 14:08:46.94: [ 1460]: --> [2:OK]
Nov 07 14:08:46.94: [ 1460]: <-- [12:ATS8=2S7=60\r]
Nov 07 14:08:47.08: [ 1460]: --> [2:OK]
Nov 07 14:08:47.08: [ 1460]: <-- [14:AT+FCLASS=2.0\r]
Nov 07 14:08:47.24: [ 1460]: --> [2:OK]
Nov 07 14:08:47.24: [ 1460]: <-- [9:AT+FLO=0\r]
Nov 07 14:08:47.38: [ 1460]: --> [2:OK]
Nov 07 14:08:47.38: [ 1460]: <-- [9:AT+FPP=0\r]
Nov 07 14:08:47.52: [ 1460]: --> [2:OK]
Nov 07 14:08:47.52: [ 1460]: <-- [9:AT+FBO=0\r]
Nov 07 14:08:47.66: [ 1460]: --> [2:OK]
Nov 07 14:08:47.66: [ 1460]: <-- [10:AT+FCT=30\r]
Nov 07 14:08:47.80: [ 1460]: --> [2:OK]
Nov 07 14:08:47.80: [ 1460]: <-- [15:AT+FNR=1,1,1,1\r]
Nov 07 14:08:47.94: [ 1460]: --> [2:OK]
Nov 07 14:08:47.94: [ 1460]: <-- [9:AT+FIE=0\r]
Nov 07 14:08:48.08: [ 1460]: --> [2:OK]
Nov 07 14:08:48.08: [ 1460]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Nov 07 14:08:48.22: [ 1460]: --> [2:OK]
Nov 07 14:08:48.22: [ 1460]: <-- [5:ATM0\r]
Nov 07 14:08:48.35: [ 1460]: --> [2:OK]
Nov 07 14:08:48.35: [ 1460]: <-- [14:AT+FCLASS=2.0\r]
Nov 07 14:08:48.59: [ 1460]: --> [2:OK]
Nov 07 14:08:48.59: [ 1460]: <-- [9:AT+FLO=0\r]
Nov 07 14:08:48.83: [ 1460]: --> [2:OK]
Nov 07 14:08:48.83: [ 1460]: <-- [9:AT+FPP=0\r]
Nov 07 14:08:49.07: [ 1460]: --> [2:OK]
Nov 07 14:08:49.07: [ 1460]: <-- [9:AT+FBO=0\r]
Nov 07 14:08:49.31: [ 1460]: --> [2:OK]
Nov 07 14:08:49.31: [ 1460]: <-- [10:AT+FCT=30\r]
Nov 07 14:08:49.55: [ 1460]: --> [2:OK]
Nov 07 14:08:49.55: [ 1460]: <-- [15:AT+FNR=1,1,1,1\r]
Nov 07 14:08:49.79: [ 1460]: --> [2:OK]
Nov 07 14:08:49.79: [ 1460]: <-- [9:AT+FIE=0\r]
Nov 07 14:08:50.03: [ 1460]: --> [2:OK]
Nov 07 14:08:50.03: [ 1460]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Nov 07 14:08:50.27: [ 1460]: --> [2:OK]
Nov 07 14:08:50.27: [ 1460]: <-- [22:AT+FLI="NothingSetup"\r]
Nov 07 14:08:50.51: [ 1460]: --> [2:OK]
Nov 07 14:08:50.51: [ 1460]: DIAL 4805546454
Nov 07 14:08:50.51: [ 1460]: <-- [15:ATDT4805546454\r]
Nov 07 14:09:02.91: [ 1460]: --> [4:+FCO]
Nov 07 14:09:06.13: [ 1460]: --> [38:+FNF:y�	��ЀIINTEL           ]
Nov 07 14:09:06.13: [ 1460]: REMOTE NSF "y�	��ЀIINTEL           "
Nov 07 14:09:06.13: [ 1460]: --> [27:+FCI:"        602 554 6454"]
Nov 07 14:09:06.13: [ 1460]: REMOTE CSI "602 554 6454"
Nov 07 14:09:06.13: [ 1460]: --> [20:+FIS:1,3,0,2,1,0,0,4]
Nov 07 14:09:06.13: [ 1460]: --> [2:OK]
Nov 07 14:09:06.13: [ 1460]: REMOTE best rate 9600 bit/s
Nov 07 14:09:06.13: [ 1460]: REMOTE max page width 1728 pixels in 215 mm
Nov 07 14:09:06.13: [ 1460]: REMOTE max unlimited page length 
Nov 07 14:09:06.13: [ 1460]: REMOTE best vres 7.7 line/mm
Nov 07 14:09:06.13: [ 1460]: REMOTE best format 2-D MR
Nov 07 14:09:06.13: [ 1460]: REMOTE best 20 ms, 10 ms/scanline
Nov 07 14:09:06.13: [ 1460]: USE 9600 bit/s
Nov 07 14:09:06.13: [ 1460]: USE 20 ms, 10 ms/scanline
Nov 07 14:09:06.13: [ 1460]: SEND file "docq/doc8.ps;00"
Nov 07 14:09:06.13: [ 1460]: USE page width 1728 pixels in 215 mm
Nov 07 14:09:06.13: [ 1460]: USE unlimited page length 
Nov 07 14:09:06.13: [ 1460]: USE 3.85 line/mm
Nov 07 14:09:06.13: [ 1460]: USE 1-D MR
Nov 07 14:09:06.13: [ 1460]: <-- [23:AT+FIS=0,3,0,2,0,0,0,4\r]
Nov 07 14:09:06.37: [ 1460]: --> [2:OK]
Nov 07 14:09:06.37: [ 1460]: <-- [7:AT+FDT\r]
Nov 07 14:09:06.65: [ 1460]: --> [20:+FCS:0,3,0,2,0,0,0,4]
Nov 07 14:09:12.53: [ 1460]: --> [7:CONNECT]
Nov 07 14:09:12.53: [ 1460]: SEND begin page
Nov 07 14:09:20.53: [ 1460]: SENT 16063 bytes of data
Nov 07 14:09:20.53: [ 1460]: SEND 1D RTC
Nov 07 14:09:20.53: [ 1460]: SEND end page
Nov 07 14:09:20.53: [ 1460]: SEND send EOP (no more pages or documents)
Nov 07 14:12:20.52: [ 1460]: REMOTE HANGUP: Unspecified Transmit Phase D error, including +FPHCTO timeout between data and +FET command (code 50)
Nov 07 14:12:20.52: [ 1460]: <-- [7:AT+FKS\r]
Nov 07 14:12:50.52: [ 1460]: MODEM <Timeout>
Nov 07 14:12:50.52: [ 1460]: <-- [5:ATH0\r]
Nov 07 14:12:55.52: [ 1460]: MODEM <Timeout>
Nov 07 14:12:55.52: [ 1460]: SESSION END




Project hosted by iFAX Solutions