flexfax: Can not send fax.

[Ertan Kucukoglu <ertank@softhome.net>]

Hello,

(Sorry for this slightly big message)

I recently setup my HylaFAX 4.1beta2 on Slackware 4.0 linux. HylaFAX can
receive faxes without problem., but I can not send fax.

sendfax -n -d xxx <<EOF
test
EOF

Command puts the job in queue, dials xxx numbered phone, xxx gives fax
signal, but HylaFAX (or my modem or faxgetty or faxmodem) can not
understand it (or I make something wrong to make it behave like this)

faxgetty runs on ttyS0, 'faxmodem ttyS0' also running, hfaxd running.

I included a few configuration files. My modem is PROLINK 1436EM Ext. on
COM1.

I come over to that point and I will not give up. (With your helps of
course :-)

Thanks in advance.

-- 
Ertan Kucukoglu
ertank@softhome.net
Oct 27 14:52:40.94: [ 1022]: SESSION BEGIN 00000056 902124250459
Oct 27 14:52:40.95: [ 1022]: SEND FAX: JOB 5 DEST 4250459 COMMID 00000056
Oct 27 14:52:40.95: [ 1022]: DELAY 2600 ms
Oct 27 14:52:43.54: [ 1022]: <-- [15:ATE0V1Q0S0=0H0\r]
Oct 27 14:52:44.31: [ 1022]: --> [2:OK]
Oct 27 14:52:44.31: [ 1022]: <-- [21:ATS8=2S7=60&K4&D2&C1\r]
Oct 27 14:52:44.47: [ 1022]: --> [2:OK]
Oct 27 14:52:44.47: [ 1022]: <-- [12:AT+FCLASS=1\r]
Oct 27 14:52:44.62: [ 1022]: --> [2:OK]
Oct 27 14:52:44.62: [ 1022]: <-- [7:ATL2M1\r]
Oct 27 14:52:44.77: [ 1022]: --> [2:OK]
Oct 27 14:52:44.77: [ 1022]: <-- [12:AT+FCLASS=1\r]
Oct 27 14:52:45.02: [ 1022]: --> [2:OK]
Oct 27 14:52:45.02: [ 1022]: DIAL 4250459
Oct 27 14:52:45.02: [ 1022]: <-- [13:ATDT4250459@\r]
Oct 27 14:53:48.48: [ 1022]: --> [9:NO ANSWER]
Oct 27 14:53:48.48: [ 1022]: SEND FAILED: No answer from remote
Oct 27 14:53:48.48: [ 1022]: SEND FAILED: No answer from remote; too many attempts to dial
Oct 27 14:53:48.48: [ 1022]: <-- [5:ATH0\r]
Oct 27 14:53:49.34: [ 1022]: --> [2:OK]
Oct 27 14:53:49.34: [ 1022]: SESSION END
# $Id: class1,v 1.2 1999/01/10 09:09:37 robert Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		90
AreaCode:		212
FAXNumber:		+90.212.598.3951
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		medium
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"NothingSetup"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use this to supply a hint
ModemRate:		19200		# rate for DCE-DTE communication
ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed
#
ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD follows carrier
#GettyArgs:		"-h %l dx_%s"	# modem must auto-detect fax/data
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:		""		# stuff to do when modem is reset
ModemAnswerCmd:		AT+FCLASS=1;A	# default is to answer as fax 
ModemNoFlowCmd:		AT&K		# disable flow control cmd
ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
ModemSoftFlowCmd:	AT&K4		# software flow control cmd
#ModemNoAutoAnswerCmd:	ATS0=1		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:	ATE0		# disable command echo
ModemVerboseResultsCmd:	ATV1		# enable verbose command results
ModemResultCodesCmd:	ATQ0		# enable result codes
ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
ModemSoftResetCmd:	ATZ		# do soft reset of modem
ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds
ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
Class1Cmd:		AT+FCLASS=1	# command to enter class 1
Class1TCFResponseDelay:	75		# 75ms delay between recv TCF & response
Class1SendPPMDelay:	75		# 75ms delay before sending PPM
Class1SendTCFDelay:	75		# 75ms delay between sending DCS & TCF
Class1TrainingRecovery:	1500		# 1.5sec delay after training failure
Class1RecvAbortOK:	200		# wait 200ms for abort response
Class1FrameOverhead:	4		# 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:	40000		# 35+5secs waiting for ident frames
Class1TCFMaxNonZero:	10		# max 10% of data may be non-zero
Class1TCFMinRun:	1000		# min run is 2/3rds of TCF duration
#
# inittab	This file describes how the INIT process should set up
#		the system in a certain run-level.
#
# Version:	@(#)inittab		2.04	17/05/93	MvS
#                                       2.10    02/10/95        PV
#                                       3.00    02/06/1999      PV
#
# Author:	Miquel van Smoorenburg, <miquels@drinkel.nl.mugnet.org>
# Modified by:	Patrick J. Volkerding, <volkerdi@ftp.cdrom.com>
#

# These are the default runlevels in Slackware:
#   0 = halt
#   1 = single user mode
#   2 = unused (but configured the same as runlevel 3)
#   3 = multiuser mode (default Slackware runlevel)
#   4 = X11 with XDM
#   5 = unused (but configured the same as runlevel 3)
#   6 = reboot

# Default runlevel. (Do not set to 0 or 6)
id:3:initdefault:

# System initialization (runs when system boots).
si:S:sysinit:/etc/rc.d/rc.S

# Script to run when going single user (runlevel 1).
su:1S:wait:/etc/rc.d/rc.K

# Script to run when going multi user.
rc:2345:wait:/etc/rc.d/rc.M

# What to do at the "Three Finger Salute".
ca::ctrlaltdel:/sbin/shutdown -t5 -rf now

# Runlevel 0 halts the system.
l0:0:wait:/etc/rc.d/rc.0

# Runlevel 6 reboots the system.
l6:6:wait:/etc/rc.d/rc.6

# What to do when power fails (shutdown to single user).
pf::powerfail:/sbin/shutdown -f +5 "THE POWER IS FAILING"

# If power is back before shutdown, cancel the running shutdown.
pg:0123456:powerokwait:/sbin/shutdown -c "THE POWER IS BACK"

# If power comes back in single user mode, return to multi user mode.
ps:S:powerokwait:/sbin/init 3

# The getties in multi user mode on consoles an serial lines.
#
# NOTE NOTE NOTE adjust this to your getty or you will not be
#                able to login !!
#
# Note: for 'agetty' you use linespeed, line.
# for 'getty_ps' you use line, linespeed and also use 'gettydefs'
c1:1235:respawn:/sbin/agetty 38400 tty1 linux
c2:1235:respawn:/sbin/agetty 38400 tty2 linux
c3:1235:respawn:/sbin/agetty 38400 tty3 linux
c4:1235:respawn:/sbin/agetty 38400 tty4 linux
c5:1235:respawn:/sbin/agetty 38400 tty5 linux
c6:12345:respawn:/sbin/agetty 38400 tty6 linux

# Serial lines
#s1:12345:respawn:/sbin/agetty 19200 ttyS0 vt100
#s2:12345:respawn:/sbin/agetty 19200 ttyS1 vt100

# Dialup lines
#d1:12345:respawn:/sbin/agetty -mt60 38400,19200,9600,2400,1200 ttyS0 vt100
#d2:12345:respawn:/sbin/agetty -mt60 38400,19200,9600,2400,1200 ttyS1 vt100

# Runlevel 4 used to be for an X-window only system, until we discovered
# that it throws init into a loop that keeps your load avg at least 1 all 
# the time. Thus, there is now one getty opened on tty6. Hopefully no one
# will notice. ;^)
# It might not be bad to have one text console anyway, in case something 
# happens to X.
x1:4:wait:/etc/rc.d/rc.4

# Hylafax icin koyuldu
#mo:2345:respawn:/usr/local/sbin/faxgetty ttyS0

# End of /etc/inittab