flexfax: Fax not being sent

[Rich <almric@imap4.asu.edu>]

I'm new to HylaFAX so please be gentle.

I'm trying to use the beta RPM on a RH Linux 6.0 Intel P166 machine.
The modem I'm using is a USR28.8 on ttyS2.  The machine is also setup
for ip masquerading.  I think I've successfully configured most of the
software I need to although I do have a few questions in addition to my
problem.  If you need more info on the system let me know.

I say most of the software seems to be set up because I can use whfc to
send a fax and it does dial the number and seems to handshake with the
fax machine.  However, it never sends anything.  Included at the bottom
of the page is one of the logs from one of the attempts to send.  As you

can see it connects to the fax on the other end and then the session is
closed without anything being sent.  Any ideas?

Also, I keep getting the:
    /bin/stty: standard input: unable to perform all requested
operations
error when faxaddmodem is run.  The only suggestion I've found in the
archives is that the FIFO.ttyS2 might not exist, but it does.  Is this a

major problem or what?

All help and suggestions are greatly appreciated,
Richard

-----------------------------------Session
log-------------------------------------
Oct 27 12:06:44.27: [  638]: SESSION BEGIN 00000003 16028089552
Oct 27 12:06:44.28: [  638]: SEND FAX: JOB 4 DEST 8089552 COMMID
00000003
Oct 27 12:06:44.28: [  638]: DELAY 2600 ms
Oct 27 12:06:46.87: [  638]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Oct 27 12:06:47.04: [  638]: --> [16:ATE0V1Q0X4S0=0H0]
Oct 27 12:06:47.04: [  638]: --> [2:OK]
Oct 27 12:06:47.04: [  638]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
Oct 27 12:06:47.21: [  638]: --> [2:OK]
Oct 27 12:06:47.21: [  638]: <-- [14:AT+FCLASS=2.0\r]
Oct 27 12:06:47.25: [  638]: --> [2:OK]
Oct 27 12:06:47.25: [  638]: <-- [9:AT+FLO=2\r]
Oct 27 12:06:47.29: [  638]: --> [2:OK]
Oct 27 12:06:47.29: [  638]: <-- [9:AT+FPP=0\r]
Oct 27 12:06:47.33: [  638]: --> [2:OK]
Oct 27 12:06:47.33: [  638]: <-- [9:AT+FBO=0\r]
Oct 27 12:06:47.37: [  638]: --> [2:OK]
Oct 27 12:06:47.37: [  638]: <-- [10:AT+FCT=30\r]
Oct 27 12:06:47.41: [  638]: --> [2:OK]
Oct 27 12:06:47.41: [  638]: <-- [15:AT+FNR=1,1,1,0\r]
Oct 27 12:06:47.45: [  638]: --> [2:OK]
Oct 27 12:06:47.45: [  638]: <-- [9:AT+FIE=0\r]
Oct 27 12:06:47.49: [  638]: --> [2:OK]
Oct 27 12:06:47.49: [  638]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Oct 27 12:06:47.54: [  638]: --> [2:OK]
Oct 27 12:06:47.54: [  638]: <-- [5:ATM0\r]
Oct 27 12:06:47.71: [  638]: --> [2:OK]
Oct 27 12:06:47.71: [  638]: <-- [14:AT+FCLASS=2.0\r]
Oct 27 12:06:47.86: [  638]: --> [2:OK]
Oct 27 12:06:47.86: [  638]: <-- [9:AT+FLO=2\r]
Oct 27 12:06:48.00: [  638]: --> [2:OK]
Oct 27 12:06:48.00: [  638]: <-- [9:AT+FPP=0\r]
Oct 27 12:06:48.14: [  638]: --> [2:OK]
Oct 27 12:06:48.14: [  638]: <-- [9:AT+FBO=0\r]
Oct 27 12:06:48.28: [  638]: --> [2:OK]
Oct 27 12:06:48.28: [  638]: <-- [10:AT+FCT=30\r]
Oct 27 12:06:48.42: [  638]: --> [2:OK]
Oct 27 12:06:48.42: [  638]: <-- [15:AT+FNR=1,1,1,0\r]
Oct 27 12:06:48.56: [  638]: --> [2:OK]
Oct 27 12:06:48.56: [  638]: <-- [9:AT+FIE=0\r]
Oct 27 12:06:48.70: [  638]: --> [2:OK]
Oct 27 12:06:48.70: [  638]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Oct 27 12:06:48.85: [  638]: --> [2:OK]
Oct 27 12:06:48.85: [  638]: <-- [22:AT+FLI="+16028089552"\r]
Oct 27 12:06:49.00: [  638]: --> [2:OK]
Oct 27 12:06:49.01: [  638]: DIAL 8089552
Oct 27 12:06:49.01: [  638]: <-- [12:ATDT8089552\r]
Oct 27 12:07:18.19: [  638]: --> [4:+FCO]
Oct 27 12:07:19.88: [  638]: --> [27:+FCI:"AIM                 "]
Oct 27 12:07:19.88: [  638]: REMOTE CSI "AIM"
Oct 27 12:07:20.29: [  638]: --> [20:+FIS:1,5,0,2,0,0,0,0]
Oct 27 12:07:20.40: [  638]: --> [2:OK]
Oct 27 12:07:20.40: [  638]: REMOTE best rate 14400 bit/s
Oct 27 12:07:20.40: [  638]: REMOTE max page width 1728 pixels in 215 mm

Oct 27 12:07:20.40: [  638]: REMOTE max unlimited page length
Oct 27 12:07:20.40: [  638]: REMOTE best vres 7.7 line/mm
Oct 27 12:07:20.40: [  638]: REMOTE best format 1-D MR
Oct 27 12:07:20.40: [  638]: REMOTE best 0 ms/scanline
Oct 27 12:07:20.40: [  638]: USE 14400 bit/s
Oct 27 12:07:20.40: [  638]: USE 0 ms/scanline
Oct 27 12:07:20.40: [  638]: <-- [5:ATH0\r]
Oct 27 12:07:20.80: [  638]: --> [2:OK]
Oct 27 12:07:20.80: [  638]: SESSION END