flexfax: ACEEX DM 1414VH - Config Problem

["Klaus J. Sch�fer" <klaus@pcxpark.de>]

HELP!! 

Does anybody use the ACEEX DM 1414VH with HylaFAX? Any help is greatly 
appreciated!
I�ve attached my config.modem-file, but with this file I can only 
recieve faxes and cannot send faxes!

May anybody send me the right config.modem-file or help me with my 
file? 

Please help a poor man with a small computer.....

Many thanks in advance!!

Klaus 



# pcXpark 1999.08.28 Configuration-File
#
#
# Copyright (c) 1997-1999 Klaus J. Sch�fer / pcXpark
#
#
#
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL KLAUS J. SCH�FER OR PCXPARK BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#
#
#
#
#
# Class 2 modem configuration (Rockwell based).
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		49
AreaCode:		941
FAXNumber:		+49.941.9455543
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		527
SessionTracing:		527
RecvFileMode:		0644
LogFileMode:		0600
DeviceMode:		0666
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-r -b -s %s %l"
LocalIdentifier:	"Klaus J. Schaefer"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		25
#
#  AT&FE0V1W1S0=0S95=47S36=7S48=7
#
#
#
# CONFIG: CLASS2: 
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use class 2 interface
ModemRate:		19200		# locked for fax sending&receiving
ModemFlowControl:	xonxoff		# default
#
ModemNoFlowCmd:		AT&K0		# disable flow control cmd
ModemSoftFlowCmd:	AT&K4		# software flow control cmd
ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
ModemSetupDTRCmd:	AT&D3		# DTR off causes modem to reset
ModemSetupDCDCmd:	AT&C1		# DCD follows carrier
ModemSetupAACmd:	AT+FAA=1	# enable adaptive-answer in Class 2
#
ModemRecvFillOrder:	MSB2LSB		# bit order of received facsimile
ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
ModemResetCmds:		AT&FE0V1W1S0=0S95=47S36=7S48=7
#
ModemDialCmd:		ATDT%s		# T for tone dialing
#
# Chip locks the line rate and switches to xon/xoff flow
# control when receiving facsimile--we must follow suit.
#
# ModemAnswerFaxBeginCmd:	"<19200><xon>"	# lock line rate & switch flow control
#
Class2RecvDataTrigger:	"\022"		# character sent to modem to start recv
Class2DDISCmd:		AT+FDIS