flexfax: Missing EOL after 5 seconds. PLEASE HELP !!!!!!!! (with log)

[Levente Janovszki <levi@goliath.bmk.hu>]

Hello !

Please somebody help me !!!! I have been trying to set up Hyla for 3 days
!!
I use a Linux 2.0.36, E-tech Bullet E1414MX modem on cua1 and cannot get
faxes .

-------CONFIGURATION
My config:
# CONFIG: CLASS2: E-TECH*-RTSCTS
# CONFIG: CLASS2: E-TECH*-DEFAULT#
# Generic Class 2 modem configuration.#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:            36AreaCode:               1
FAXNumber:              "+36 1 349-7986"LongDistancePrefix:     06
InternationalPrefix:    011
DialStringRules:        etc/dialrules
#ServerTracing:         139
SessionTracing:         8191
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          Low
GettyArgs:              "-h %l %s"
LocalIdentifier:        "Incoming SZTAKI fax server"
LogFacility:            local0
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
MaxRecvPages:           25
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2          # use this to supply a hint
ModemRate:              19200           # max rate for DCE-DTE
communication
ModemFlowControl:       xonxoff         # default
#ModemFlowControl:      rtscts          # default

#
ModemSoftFlowCmd:       AT$F0           # software XON/XOFF local flow
control
ModemHardFlowCmd:       AT$F4           # hardware flow control
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
(or not)
ModemSetupAACmd:        AT+FAA=1
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:           ATDP%s          # T for tone dialing, @ for
silence
#
Class2DDISCmd:          AT+FDIS         # fix for resolution problems
Class2RecvDataTrigger:  "\022"          # DC2
Class2REVCmd:           ""
ModemOnHookCmd:         <waitfor:OK>
#ModemAnswerFaxBeginCmd:        "<9600><xon>"
ModemRecvFillOrder:     MSB2LSB



--------SESSION LOG
And my log:

Jun 24 21:07:46.63: [ 5743]: SESSION BEGIN 00000016 3613497986
Jun 24 21:07:46.63: [ 5743]: <-- [4:ATA\r]
Jun 24 21:07:56.74: [ 5743]: --> [5:+FCON]
Jun 24 21:07:56.74: [ 5743]: ANSWER: FAX CONNECTION
Jun 24 21:07:56.74: [ 5743]: STATE CHANGE: ANSWERING -> RECEIVING
Jun 24 21:07:56.74: [ 5743]: MODEM input buffering enabled
Jun 24 21:07:56.74: [ 5743]: RECV FAX: begin
Jun 24 21:08:01.43: [ 5743]: --> [29:+FTSI: "   SZTAKI fax server"]
Jun 24 21:08:01.43: [ 5743]: REMOTE TSI "SZTAKI fax server"
Jun 24 21:08:01.43: [ 5743]: --> [22:+FDCS: 1,5,0,0,0,0,0,0]
Jun 24 21:08:01.43: [ 5743]: REMOTE wants 14400 bit/s
Jun 24 21:08:01.43: [ 5743]: REMOTE wants page width 1728 pixels in 215 mm
Jun 24 21:08:01.43: [ 5743]: REMOTE wants A4 page length (297 mm)
Jun 24 21:08:01.43: [ 5743]: REMOTE wants 7.7 line/mm
Jun 24 21:08:01.43: [ 5743]: REMOTE wants 1-D MR
Jun 24 21:08:01.43: [ 5743]: --> [2:OK]
Jun 24 21:08:01.43: [ 5743]: <-- [7:AT+FDR\r]
Jun 24 21:08:01.92: [ 5743]: --> [5:+FCFR]
Jun 24 21:08:03.92: [ 5743]: --> [7:CONNECT]
Jun 24 21:08:03.92: [ 5743]: RECV: begin page
Jun 24 21:08:03.92: [ 5743]: MODEM set XON/XOFF/FLUSH: input ignored,
output generated
Jun 24 21:08:03.92: [ 5743]: RECV: send trigger 022
Jun 24 21:08:03.92: [ 5743]: <-- data [1]
Jun 24 21:09:10.56: [ 5743]: MODEM TIMEOUT: reading from modem
Jun 24 21:09:10.56: [ 5743]: <-- data [1]
Jun 24 21:09:10.56: [ 5743]: RECV: Missing EOL after 5 seconds
Jun 24 21:09:10.56: [ 5743]: MODEM set XON/XOFF/DRAIN: input interpreted,
output disabled
Jun 24 21:09:10.56: [ 5743]: REMOTE HANGUP: Missing EOL after 5 seconds
(section 3.2/T.4) (code 91)
Jun 24 21:09:10.56: [ 5743]: RECV FAX (00000016): recvq/fax00007.tif from
SZTAKI fax server, route to <unspecified>, 0 pages in 1:14
Jun 24 21:09:10.57: [ 5743]: RECV FAX: Missing EOL after 5 seconds
(section 3.2/T.4)
Jun 24 21:09:10.57: [ 5743]: <-- [6:AT+FK\r]
Jun 24 21:09:10.78: [ 5743]: --> [2:OK]
Jun 24 21:09:10.78: [ 5743]: RECV FAX (00000016): session with SZTAKI fax
server terminated abnormally: Missing EOL after 5 seconds (section
3.2/T.4)
Jun 24 21:09:10.78: [ 5743]: RECV FAX: bin/faxrcvd "recvq/fax00007.tif"
"cua1" "00000016" "Missing EOL after 5 seconds (section 3.2/T.4)"
Jun 24 21:09:11.14: [ 5743]: RECV FAX: end
Jun 24 21:09:11.14: [ 5743]: SESSION END



Thanx!!!!!!!!!!!!!!

Regards:
Levente
| Levente Janovszki  | Bekes County Library          JUST 4 lines 4 U |
| levi@athos.bmk.hu  | Bekescsaba, Derkovits sor 1. HUNGARY Zip: 5600 |
| Linux. Just use it |     *    The operating system collapsed    *   |  
| w/o fear of panic: |     *            OK    Cancel              *   |