flexfax: US Robotics Message (sportster Message plus) Firmware 12.1.25

[Bernd Bradenahl <bbrade@arco-online.de>]

Hey,

I've installed Hylafax 4.0pl2 on SuSE-Linux 6.1 with Kernel 2.2.5
My Modem US Robotics Message (sportster Message plus model 5668) with
Firmware 12.1.25
only receives the fist page of a fax and then stops the transmision
(with class2.0 as well as with class1).

The newest sm+ program from 3Com.messagecentral.de does not work neither
- but the messenger 0.0.3 does).

Did anyone manage to make this Firmware work with hylafax. I had to
flash the firmware from 12.1.24 to 12.1.25 to make the standalone
faxreceive work.

The USR "support" rejects support for Linux. So you can perhaps help me.

Ciao

Bernd Bradenahl


My actual config.modem is:

# Generic Class 2.0 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		49
AreaCode:		30
FAXNumber:		"+49 30 29000996"
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:          0x3ffff
SessionTracing:         0x3ffff
RecvFileMode:		0644
LogFileMode:		0600
DeviceMode:		0666
RingsBeforeAnswer:	1
SpeakerVolume:		quiet
GettyArgs:		"-r -b -s %s %l"
LocalIdentifier:	"Bernd Bradenahl"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
# QualifyTSI:		etc/tsi
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2.0	# use this to supply a hint
ModemRate:		38400		# rate for DCE-DTE communication
ModemFlowControl:       rtscts          # hardware flow control assumed
ModemSetupDTRCmd:	AT&D2	 	# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
ModemSetupAACmd:        AT+FAA=1
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#                                       Achtung: @ macht bei mir
Probleme !!!!!
ModemDialCmd:		ATDT%s		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:		AT&F1S19=2	# stuff to do when modem is reset
ModemAnswerCmd:		ATA		# use this to answer phone
ModemNoFlowCmd:		AT&H0&I0&R1	# setup modem for no flow control
ModemHardFlowCmd:	AT&H1&I0&R2	# setup modem for hardware flow control
ModemSoftFlowCmd:	AT&H2&I2&R1	# setup modem for software flow control
ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:	ATE0		# disable command echo
ModemVerboseResultsCmd:	ATV1		# enable verbose command results
ModemResultCodesCmd:	ATQ0X4		# enable result codes
ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
ModemSoftResetCmd:	ATZ		# do soft reset of modem
ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds
ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:		AT+FCLASS=2.0	# command to enter class 2.0
Class2BORCmd:		AT+FBO=0	# bit order for phase B/C/D (direct)
Class2CQCmd:		""		# commands to enable copy quality proc.
Class2AbortCmd:		AT+FKS		# abort session command
Class2CQQueryCmd:       !(0),(0)        # override modem response
#Class2CQQueryCmd:	AT+FCQ=?	# query for copy quality capabilities
Class2DCCQueryCmd:	AT+FCC=?	# query for modem capabilities
Class2TBCCmd:		AT+FPP=0	# setup stream mode
Class2CRCmd:		AT+FCR=1	# enable capability to receive
Class2PHCTOCmd:		AT+FCT=30	# set phase C timeout parameter
Class2BUGCmd:		AT+FBU=0	# disable HDLC frame tracing
Class2LIDCmd:		AT+FLI		# set local identifier command
Class2DCCCmd:		AT+FCC		# set modem capabilities command
Class2DISCmd:		AT+FIS		# set session parameters command
Class2DDISCmd:		""		# disable pre-dial DIS command hack
Class2CIGCmd:		AT+FPI		# set polling identifier command
Class2NRCmd:		AT+FNR=1,1,1,0	# setup status reporting command
Class2PIECmd:		AT+FIE=0	# disable interrupt-enable command
Class2PTSCmd:		AT+FPS		# set post-page status command
Class2SPLCmd:		AT+FSP		# set polling indicator command
Class2NFLOCmd:		AT+FLO=0	# set no flow control command
Class2SFLOCmd:		AT+FLO=1	# set software flow control command
Class2HFLOCmd:		AT+FLO=2	# set hardware flow control command